scholarly journals DIFFUSIVE AND DISPLACIVE PHASE TRANSFORMATIONS UNDER HIGH PRESSURE TORSION

2019 ◽  
Vol 25 (4) ◽  
pp. 230 ◽  
Author(s):  
Boris Straumal ◽  
Askar Kilmametov ◽  
Andrey Mazilkin ◽  
Olga Kogtenkova ◽  
Brigitte Baretzky ◽  
...  
Keyword(s):  
Mass Transfer ◽  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
Phase Composition ◽  
Steady State ◽  
Phase Transformations ◽  
High Pressure Torsion ◽  
Dynamic Equilibrium ◽  
Initial State

<p class="AMSmaintext"><span lang="EN-GB">Severe plastic deformation (SPD) can induce various phase transformations. After a certain strain, the dynamic equilibrium establishes between defects production by an external force and their relaxation (annihilation). The grain size, hardness, phase composition etc. in this steady-state does not depend on the initial state of a material and is, therefore, equifinal. In this review we discuss the competition between precipitation and dissolution of precipitates, amorphization and (nano)crystallization, SPD-induced accelerated mass-transfer, allotropic and martensitic transitions and formation of grain boundary phases.</span></p>

The Processing of Ultrafine-Grained Materials Using High-Pressure Torsion

2007 ◽  
Vol 558-559 ◽  
pp. 1283-1294 ◽  
Author(s):  
Cheng Xu ◽  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
High Pressure Torsion ◽  
Metallic Materials ◽  
Grain Sizes ◽  
Ultrafine Grained ◽  
Wide Range ◽  
Ultrafine Grained Materials ◽  
Thin Disks

It is now well-established that processing through the application of severe plastic deformation (SPD) leads to a significant reduction in the grain size of a wide range of metallic materials. This paper examines the fabrication of ultrafine-grained materials using high-pressure torsion (HPT) where this process is attractive because it leads to exceptional grain refinement with grain sizes that often lie in the nanometer or submicrometer ranges. Two aspects of HPT are examined. First, processing by HPT is usually confined to samples in the form of very thin disks but recent experiments demonstrate the potential for extending HPT also to bulk samples. Second, since the strains imposed in HPT vary with the distance from the center of the disk, it is important to examine the development of inhomogeneities in disk samples processed by HPT.

scholarly journals Plastic Deformation of BaTiO3Ceramics by High-pressure Torsion and Changes in Phase Transformations, Optical and Dielectric Properties

2015 ◽  
Vol 3 (4) ◽  
pp. 216-221 ◽  
Author(s):  
Kaveh Edalati ◽  
Masashi Arimura ◽  
Yoshifumi Ikoma ◽  
Takeshi Daio ◽  
Moriji Miyata ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Dielectric Properties ◽  
Phase Transformations ◽  
High Pressure Torsion

Structure and Properties of Grain Boundaries in Submicrocrystalline W Obtained by Severe Plastic Deformation

2009 ◽  
Vol 283-286 ◽  
pp. 629-638 ◽  
Author(s):  
Vladimir V. Popov ◽  
Ruslan Valiev ◽  
E.N. Popova ◽  
A.V. Sergeev ◽  
A.V. Stolbovsky ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Boundaries ◽  
High Pressure Torsion ◽  
Submicrocrystalline Structure ◽  
Emission Mössbauer Spectroscopy ◽  
Structure And Properties ◽  
Initial State

Submicrocrystalline structure of W obtained by severe plastic deformation (SPD) by high pressure torsion (5 revolutions of anvils at 4000C) and its thermal stability have been examined by TEM. Grain boundaries of submicrocrystalline W have been studied by the method of the emission Mössbauer spectroscopy in the initial state and after annealing at 400-6000С.

Phase Transformations in Pearlitic Steels Induced by Severe Plastic Deformation

2006 ◽  
Vol 114 ◽  
pp. 133-144 ◽  
Author(s):  
Julia Ivanisenko ◽  
Ian MacLaren ◽  
Xavier Sauvage ◽  
Ruslan Valiev ◽  
Hans Jorg Fecht
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Phase Transformations ◽  
High Pressure Torsion ◽  
Pearlitic Steel ◽  
Carbon Steels ◽  
Coarse Grained ◽  
Cold Plastic Deformation ◽  
The Stability ◽  
Nanocrystalline Ferrite

The paper presents an overview of a number of unusual phase transformations which take place in pearlitic steels in conditions of the severe deformation, i.e. combination of high pressure and strong shear strain. Strain-induced cementite dissolution is a well-documented phenomenon, which occurs during cold plastic deformation of pearlitic steels. Recently new results which can shed additional light on the mechanisms of this process were obtained thanks to 3DAP and HRTEM investigations of pearlitic steel deformed by high pressure torsion (HPT). It was shown that the process of cementite decomposition starts by carbon depletion from the carbides, which indicates that the deviation of cementite’s chemical composition from the stoichiometric is the main reason for thermodynamic destabilisation of cementite during plastic deformation. Important results were obtained regarding the distribution of released carbon atoms in ferrite. It was experimentally confirmed that carbon segregates to the dislocations and grain boundaries of nanocrystalline ferrite. Another unusual phase transformation taking place in nanocrystalline pearlitic steel during room temperature HPT is a stress induced α→γ transformation, which never occurs during conventional deformation of coarse grained iron and carbon steels. It was concluded that this occurred due to a reverse martensitic transformation. The atomistic mechanism and the thermodynamics of the transformation, as well as issues related to the stability of the reverted austenite will be discussed.

Thermo- and Deformation Induced Martensitic Transformations in Binary TiNi-Based Alloys Subjected to Severe Plastic Deformation

2013 ◽  
Vol 738-739 ◽  
pp. 530-534 ◽  
Author(s):  
Natalia N. Kuranova ◽  
Vladimir V. Makarov ◽  
Vladimir G. Pushin ◽  
Alexey N. Uksusnikov
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
High Pressure Torsion ◽  
Amorphous State ◽  
Cold Drawing ◽  
Martensitic Transformations ◽  
Subsequent Annealing ◽  
Structure And Phase Transformations

Results of investigations of structure and phase transformations and properties of the TiNi-based alloys with a shape memory effect (SME) after severe plastic deformation (SPD) by cold rolling, cold drawing, high pressure torsion and subsequent annealing are reported. It is found that the baroelastic effects related to the highly reversible martensitic transformations can occur in alloys, subjected to high pressure. The evolution of fine structure of the alloys into nanocrystalline and then amorphous state during SPD and after subsequent annealing have been studied. The effect of grain size on the martensitic transformations and properties of the alloys is discussed.

Comparison between FEM and Experimental Results in the Upsetting of Nano-Structured Materials

2012 ◽  
Vol 713 ◽  
pp. 31-36 ◽  
Author(s):  
C.J. Luis-Pérez ◽  
Ignacio Puertas ◽  
Daniel Salcedo ◽  
Javier León ◽  
Ivan Pérez
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Equal Channel Angular Extrusion ◽  
High Pressure Torsion ◽  
Experimental Results ◽  
Structured Materials ◽  
Angular Extrusion ◽  
Deformation Processes

Over recent years, some severe plastic deformation processes have been developed with the aim of obtaining a material with sub-micrometric or even nanometric grain size, such as: ECAE (Equal channel angular extrusion) and HPT (High pressure torsion) among many others. The main aim of this present study is to analyse the upsetting of the 5083 Al-Mg-Mn alloy, which had been previously deformed by ECAE. Different processing temperatures will be used and the final properties of the resulting material will be determined.

Severe Plastic Deformation under High Pressure for Production of Superplastic Materials

2016 ◽  
Vol 838-839 ◽  
pp. 287-293 ◽  
Author(s):  
Zenji Horita
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Refinement ◽  
High Pressure Torsion ◽  
High Strength ◽  
Al Alloys ◽  
Strain Rates ◽  
Ti Alloys

Grain refinement is an important prerequisite for advent of superplasticity. In particular, as the grain size is smaller, the superplasticity appears at higher strain rates and lower temperatures. Severe plastic deformation (SPD) is a useful process for achieving significant grain refinement. This presentation shows that applicability of the SPD process is enhanced when it is operated under high pressure through high-pressure torsion (HPT) and high-pressure sliding (HPS). It is demonstrated that commercially available conventional alloys but less ductile alloys such as Mg alloys, age-hardenable high-strength Al alloys (A2024, A7075) and Ti alloys become superplastic after processing by HPT or HPS.

Sign in / Sign up

Export Citation Format

Share Document