812 Effect on martensite phase of low-carbon steel with Si and P

2010 ◽  
Vol 2010.46 (0) ◽  
pp. 249-250
Author(s):  
Jun OKITA ◽  
Mitsuo NOTOMI ◽  
Tetsunori HADA
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Martensite Phase ◽  
Low Carbon

scholarly journals Pengaruh Media Arang Kayu Bakau Mangrove Dan Arang Kayu Asam Pada Proses Perlakuan Carburizing Terhadap Sifat Mekanik Baja Karbon ST-37

2021 ◽  
Vol 12 (2) ◽  
pp. 30-37
Author(s):  
Rico Arifandi ◽  
Gerald Adityo Pohan
Keyword(s):  
Carbon Steel ◽  
Heating Temperature ◽  
Surface Hardness ◽  
Low Carbon Steel ◽  
Martensite Phase ◽  
Wood Charcoal ◽  
Holding Time ◽  
Low Carbon ◽  
Solid Media ◽  
The Impact

In the military field, tank is armored fighting vehicles that move using chain-shaped wheels. The tread of the tank chain is a component to tread and move so that it requires tougher properties on the surface and has ductile and tough properties on the inside and is more resistant to wear on the surface. The development of tank chain production materials is necessary for the independence of national defense and security as well as reducing dependence on imports. Imported tank chain hardness value 28 HRC or 286 HV. In this research, the objective of this research is to increase the surface hardness of the steel by carburizing the initial material, especially the low carbon steel ST-37. The carburizing treatment process is a method of adding carbon content in steel using solid media. The carbon media used were mangrove charcoal and tamarind wood charcoal using calcium carbonate (CaCO3) catalyst at a constant heating temperature of 900ºC, variations in holding time of 30 minutes, 60 minutes and 90 minutes, cooled rapidly with water media. Then performed an analysis of the effect of the type of wood charcoal on the mechanical properties of carbon steel ST-37. The results obtained will be applied to the tank chain tread production process. The results of the micro structure of martensite and the highest hardness value were found in the holding time of 60 minutes of mangrove charcoal media with the microstructure results of 63.8% martensite, 36.2% bainite and a hardness value of 453.1 HV. The highest toughness value is found in the holding time of 60 minutes of tamarind wood charcoal media with an impact price (HI) of 0.4345 J/mm2. The difference between the impact test results of tamarind charcoal media with mangroves is not too significant. The higher the martensite phase, the higher the hardness value. However, there is also a bainite phase which can increase the toughness of the steel which will be used as a tread chain production material.

scholarly journals Nanoindentation-Based Micro-Mechanical and Electrochemical Properties of Quench-Hardened, Tempered Low-Carbon Steel

Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 508 ◽  
Author(s):  
Muhammad ArslanHafeez ◽  
Muhammad Usman ◽  
Muhammad Adnan Arshad ◽  
Malik AdeelUmer
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Electrochemical Properties ◽  
Lath Martensite ◽  
Low Carbon Steel ◽  
Martensite Phase ◽  
Indentation Hardness ◽  
Low Carbon ◽  
Hno3 Solution ◽  
Quench Hardening

The nanoindentation technique is widely used to measure the micro-scale mechanical properties of various materials. Herein, the nanoindentation-based micro-mechanical and electrochemical properties of low-carbon steel were investigated after quench hardening and tempering processes. The steel was produced on a laboratory scale and subjected to quench hardening separately in two different media-water and brine (10 wt% NaCl)-and subsequent moderate temperature tempering. Microstructure analysis revealed that the lath martensite phase formed after all heat treatments, having different carbon percentages ranging from 0.26% to 0.58%. A ferrite phase was also observed in the microstructure in three different morphologies, i.e., allotriomorphic ferrite, idiomorphic ferrite, and Widmanstätten ferrite. Nanoindentation analysis showed that the brine quench hardening process provided a maximum twofold improvement in indentation hardness and a 51% improvement in stiffness with a 30% reduction in reduced elastic modulus compared with as-received steel. Electrochemical performance was also evaluated in a 1% HNO3 solution. The water quench-hardened and tempered sample exhibited the highest corrosion resistance, whereas the brine quench-hardened sample exhibited the lowest corrosion resistance among all heat-treated samples.

Development of trimming technology for hot rolled ultra-low carbon steel

1993 ◽  
Vol 90 (7-8) ◽  
pp. 917-922
Author(s):  
Y. Matsuda ◽  
M. Nishino ◽  
J. Ikeda
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Ultra Low Carbon Steel ◽  
Hot Rolled

The Effect of Small Defects on Fatigue Life of a Low Carbon Steel

2019 ◽  
Author(s):  
Natalia Gonçalves Torres ◽  
Vinícius Rodrigues ◽  
Edgar Mamiya
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon

Estimation of Some Mechanical Properties for Similar & Dissimilar Welded Joints

2014 ◽  
Vol 2 (1) ◽  
pp. 59-76
Author(s):  
Abdullah Daie'e Assi
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Austenitic Stainless Steel ◽  
Base Metal ◽  
Welded Joints ◽  
Plate Thickness ◽  
Low Carbon Steel ◽  
Dissimilar Metals ◽  
Low Carbon ◽  
Steel Type

This research deals with the choice of the suitable filler metal to weld the similar and dissimilar metals (Low carbon steel type A516 & Austenitic stainless steel type 316L) under constant conditions such as, plate thickness (6 mm), voltage (78 v), current (120 A), straight polarity. This research deals with three major parts. The first parts Four types of electrodes were used for welding of dissimilar metals (C.St A516 And St.St 316L) two from mild steel (E7018, E6013) and other two from austenitic stainless steel (E309L, E308L) various inspection were carried out include (Visual T., X-ray T., δ- Ferrite phase T., and Microstructures T.) and mechanical testing include (tensile T., bending T. and micro hardness T.) The second parts done by used the same parameters to welding similar metals from (C.St A516) Or (St.St 316L). The third parts deals with welding of dissimilar weldments (C.St And St.St) by two processes, gas tungsten are welding (GTAW) and shielded metal are welding (SMAW).        The results indicated that the spread of carbon from low carbon steel to the welding zone in the case of welding stainless steel elect pole (E309L) led to Configuration Carbides and then high hardness the link to high values ​​compared with the base metal. In most similar weldments showed hardness of the welding area is  higher than the hardness of the base metal. The electrode (E309L) is the most suitable to welding dissimilar metals from (C.St A516 With St.St 316L). The results also showed that the method of welding (GTAW) were better than the method of welding (SMAW) in dissimilar welded joints (St.St 316L with C.St A516) in terms of irregular shape and integrity of the welding defects, as well as characterized this weldments the high-lift and resistance ductility good when using the welding conditions are similar.

Sign in / Sign up

Export Citation Format

Share Document