scholarly journals Hydrodynamic Lubrication of Journal Bearings by Pseudo-Plastic Lubricants : Part 2, Experimental Studies

1970 ◽  
Vol 36 (287) ◽  
pp. 1194-1201
Author(s):  
Sanae WADA ◽  
Hirotsugu HAYASHI
Keyword(s):  
Hydrodynamic Lubrication ◽  
Experimental Studies ◽  
Journal Bearings ◽  
Plastic Lubricants

Static Characteristics of Journal Bearings With Square Dimples

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Hiroo Taura ◽  
Satoru Kaneko
Keyword(s):  
Hydrodynamic Lubrication ◽  
Numerical Models ◽  
Experimental Studies ◽  
Surface Texturing ◽  
Hydrodynamic Pressure ◽  
Journal Bearings ◽  
Friction Torque ◽  
Operating Conditions ◽  
Static Characteristics ◽  
Lubrication Performance

Surface texturing is a technique for improving frictional and hydrodynamic performances of journal bearings because microtextures can serve as reservoirs for oil or traps for debris and may also generate hydrodynamic pressure. Over the past two decades, many researchers have experimentally demonstrated that texturing of various tribological elements can reduce friction force and wear, contributing to improvement of lubrication performance. Some numerical studies have examined the hydrodynamic lubrication conditions and reported that surface texturing affects the static characteristics of journal bearings, such as their load carrying capacity and friction torque. However, the validity of these numerical models has not been confirmed because of a lack of experimental studies. This study proposes a numerical model that includes both inertial effects and energy loss at the edges of dimples on the surface of a journal bearing in order to investigate the bearing's static characteristics. Experimental verification of journal bearings is also conducted with a uniform square-dimple pattern on their full-bearing surface. The results obtained by the model agree well with those of experiment, confirming the model's validity. These results show that under the same operating conditions, textured bearings yield a higher eccentricity ratio and lower attitude angle than the conventional ones with a smooth surface. This tendency becomes more marked for high Reynolds number operating conditions and for textured bearings with a large number of dimples.

Performance of Stern Tube Bearings under Different Lubrication and Operating Conditions

2009 ◽  
Author(s):  
Jan H. Andersen ◽  
Hiroyuki Sada ◽  
Seiji Yamajo
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Water Soluble ◽  
Analysis Tool ◽  
Test Rig ◽  
Experimental Performance ◽  
Shaft Alignment ◽  
Alignment Analysis

This paper presents the results of an investigation into the theoretical and experimental performance of oil lubricated journal bearings. DNV has developed a new calculation tool for the analysis of journal bearing performance as part of shaft alignment analysis. The results of the calculation tool have been compared to other research and analysis methods under static and dynamic conditions. In addition, white metal bearings were tested with decreasing Sommerfeld number until loss of hydrodynamic lubrication. The experiments were carried out in a bearing test rig and with three different lubricants, normal mineral oil, emulsifying oil, and water-soluble oil. The tests were done with increasing water content in the lubricant. Results from the test were compared with calculation using the DNV analysis tool.

scholarly journals Theoretical and Experimental Investigations on Transient Run-Up Procedures of Journal Bearings Including Mixed Friction Conditions

Lubricants ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 105 ◽  
Author(s):  
Maximilian Prölß ◽  
Hubert Schwarze ◽  
Thomas Hagemann ◽  
Philipp Zemella ◽  
Philipp Winking
Keyword(s):  
Experimental Data ◽  
Energy Equation ◽  
Hydrodynamic Lubrication ◽  
Frictional Coefficient ◽  
Journal Bearings ◽  
Numerical Code ◽  
Experimental Investigations ◽  
Lubrication Regime ◽  
Mixed Friction ◽  
Run Up

This paper focuses on the operating behavior of journal bearings for industrial machinery application during run-ups. For this purpose, a numerical simulation code that is based on a two-dimensional extended and generalized Reynolds equation and a full three-dimensional energy equation, was advanced by a theoretical model considering the effects of mixed friction and warming of journal components during start-up. The mixed friction routine contained the elastic half-spaces model proposed by Boussinesq, which considers the influence of rough surfaces by implementing flow factors and calculates additional stiffness and dissipation in areas with solid interactions. Furthermore, a transient term was added in the energy equation to consider the thermal inertia of journal, and bearing to ensure a realistic heating during run-ups. Results of the prediction were compared to experimental data taken from a special test rig built up for validation procedures. Besides the conventional sensors for temperature, oil flow, and relative motion between shaft and stator, a contact voltage measurement was installed to determine the intensity of mixed friction. The evaluation of experimental data by Stribeck curves, based on a shaft torsion measurement, indicated a significant influence of run-up time on frictional moment. The friction coefficient of the rotor bearing system was strongly influenced by the run-up time. A short run-up time reduced the frictional coefficient in the mixed lubrication regime while the opposite behavior was observed in the hydrodynamic lubrication regime. The numerical code predicted these tendencies in good agreement with experimental data, however, only if the transient energy model was applied.

A Contact-Wear Model for the EHL Analysis of Engine Journal Bearings

2005 ◽  
Author(s):  
Ducai Wang
Keyword(s):  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Surface Profile ◽  
Journal Bearings ◽  
Bearing Surface ◽  
Wear Model ◽  
Contact Wear ◽  
Analysis Technique ◽  
Elastic Distortion ◽  
Account Interaction

Engine journal bearings are now routinely analysed using elasto-hydrodynamic lubrication (EHL) methods [1,2]. This analysis technique takes into account interaction of the hydrodynamic film with the elastic distortion produced in both the bearing and the journal. It has proved a robust analytic tool for designers in predicting the value and location of such parameters as minimum oil film thickness and maximum film pressure. However, for some very heavily loaded cases, the normal EHL analysis technique may fail to produce realistic solutions. Due to ‘cusping’ of the bearing surface under extreme pressures the edges of bearing may be predicted to penetrate the journal surface leading to a ‘negative’ film thickness. In reality, the surfaces will interact and a ‘running-in’ process will result in subtle changes to the bearing surface profile such that a hydrodynamic film can be maintained across the whole bearing surface. This study introduces a contact-wear model which attempts to model this situation.

Sign in / Sign up

Export Citation Format

Share Document