scholarly journals Heat loss and heat release on premixture combustion in a stratified charge spark ignition engine with an auxiliary combustion chamber.

1985 ◽  
Vol 51 (467) ◽  
pp. 2243-2248 ◽  
Author(s):  
Hidenori TASAKA ◽  
Hiroyuki YAMAMOTO ◽  
Shin MATSUOKA
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Stratified Charge

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

Study on Different Flame Jet Ignition Variants in a Stratified Charge Spark Ignition Engine

2002 ◽  
Author(s):  
Edward Rakosi ◽  
Radu Rosca
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Output Power ◽  
Cylinder Head ◽  
Fuel Injection ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Working Process ◽  
Stratified Charge ◽  
Direct Fuel Injection

The paper presents some experimental results regarding a stratified charge spark ignition engine. We have applied the divided combustion chamber concept, using a flame jet in order to ignite the fuel-air mixture. The fueling system was a combined one: the cylinder head combustion chamber (secondary, auxiliary) was fueled by direct fuel injection, while the main combustion chamber was fueled with lean mixture by the means of a carburetor. During the tests we have used two types of main combustion chamber and three types of secondary combustion chamber. Thus, we had the possibility to use different compression ratios, starting with the lower ones, imposed by the less volatile fuels and ending with the higher ones, that led to the highest output power and a steady working process. In the meantime, three types of spark plugs were tested. We have also studied the HC and CO emissions, as well as the fuel consumption.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

2021 ◽  
pp. 146808742110346
Author(s):  
Sanguk Lee ◽  
Gyeonggon Kim ◽  
Choongsik Bae
Keyword(s):  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Transport Sector ◽  
Injection Timing ◽  
Ignition Timing ◽  
Particulate Emission ◽  
Stratified Charge ◽  
Lean Limit

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

Comparison Between Measured Radiance and a Radiation Model in a Spark-Ignition Engine

1990 ◽  
Vol 112 (3) ◽  
pp. 331-334 ◽  
Author(s):  
J. Yang ◽  
S. L. Plee ◽  
D. J. Remboski ◽  
J. K. Martin
Keyword(s):  
Heat Release ◽  
Release Rate ◽  
Maximum Rate ◽  
Spark Ignition ◽  
Rate Of Change ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Maximum Heat ◽  
Radiant Intensity ◽  
Maximum Heat Release

Measurements of the radiant emission in the near infrared have been obtained in a spark-ignition engine over a wide range of operating conditions. The system includes an in-cylinder optical sensor and associated detector. Prior work has shown correlations between the measured radiance and pressure quantities such as maximum cylinder pressure, crank angle of maximum pressure, and Indicated Mean Effective Pressure. Here are presented comparisons between the radiant intensity and a simplified model of the radiation emission, which demonstrate that the measured intensity is a function of the mass-burn fraction, mean burned-gas temperature, and the exposed combustion-chamber surface area. Further simplification leads to the conclusion that the time of the maximum rate of change of radiant intensity is the same as for the maximum heat-release rate, leading to the possibility of feedback control of spark timing. In addition, the magnitudes of the maximum rate of change of radiant emission and maximum heat-release rate have a linear relationship over a range of different operating conditions.

Numerical Investigation of Fuel Property Effects on Mixed-Mode Combustion in a Spark-Ignition Engine

2019 ◽  
Author(s):  
Chao Xu ◽  
Pinaki Pal ◽  
Xiao Ren ◽  
Sibendu Som ◽  
Magnus Sjöberg ◽  
...  
Keyword(s):  
Heat Release ◽  
Flame Propagation ◽  
Heat Release Rate ◽  
Release Rate ◽  
Octane Number ◽  
Mixed Mode ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Chemical Effect ◽  
Auto Ignition

Abstract In the present study, mixed-mode combustion of an E30 fuel in a direct-injection spark-ignition engine is numerically investigated at a fuel-lean operating condition using multidimensional computational fluid dynamics (CFD). A fuel surrogate matching Research Octane Number (RON) and Motor Octane Number (MON) of E30 is first developed using neural network based non-linear regression model. To enable efficient 3D engine simulations, a 164-species skeletal reaction mechanism incorporating NOx chemistry is reduced from a detailed chemical kinetic model. A hybrid approach that incorporates the G-equation model for tracking turbulent flame front, and the multi-zone well-stirred reactor model for predicting auto-ignition in the end gas, is employed to account for turbulent combustion interactions in the engine cylinder. Predicted in-cylinder pressure and heat release rate traces agree well with experimental measurements. The proposed modelling approach also captures moderated cyclic variability. Two different types of combustion cycles, corresponding to purely deflagrative and mixed-mode combustion, are observed. In contrast to the purely deflagrative cycles, mixed-mode combustion cycles feature early flame propagation followed by end-gas auto-ignition, leading to two distinctive peaks in heat release rate traces. The positive correlation between mixed-mode combustion cycles and early flame propagation is well captured by simulations. With the validated numerical setup, effects of NOx chemistry on mixed-mode combustion predictions are investigated. NOx chemistry is found to promote auto-ignition through residual gas recirculation, while the deflagrative flame propagation phase remains largely unaffected. Local sensitivity analysis is then performed to understand effects of physical and chemical properties of the fuel, i.e., heat of evaporation (HoV) and laminar flame speed (SL). An increased HoV tends to suppress end-gas auto-ignition due to increased vaporization cooling, while the impact of HoV on flame propagation is insignificant. In contrast, an increased SL is found to significantly promote both flame propagation and auto-ignition. The promoting effect of SL on auto-ignition is not a direct chemical effect; it is rather caused by an advancement of the combustion phasing, which increases compression heating of the end gas.

Sign in / Sign up

Export Citation Format

Share Document