scholarly journals Low-solidity cascade diffuser for transonic centrifugal compressor.

1989 ◽  
Vol 55 (511) ◽  
pp. 758-763 ◽  
Author(s):  
Hiroshi HAYAMI ◽  
Yasutoshi SENOO ◽  
Koji UTSUNOMlYA ◽  
Hiroshi HASEGAWA ◽  
Nobumasa KAWAGUCHI
Keyword(s):  
Centrifugal Compressor ◽  
Transonic Centrifugal Compressor ◽  
Low Solidity Cascade Diffuser

Flow With Shock Waves in a Transonic Centrifugal Compressor With a Low-Solidity Cascade Diffuser Using PIV

2004 ◽  
Author(s):  
Hiroshi Hayami ◽  
Masahiro Hojo ◽  
Norifumi Hirata ◽  
Shinichiro Aramaki
Keyword(s):  
Shock Wave ◽  
Shock Waves ◽  
Centrifugal Compressor ◽  
Gas Flow ◽  
Pressure Ratio ◽  
Transonic Centrifugal Compressor ◽  
Image Velocimetry ◽  
Rotor Stator Interaction ◽  
Rotating Impeller ◽  
Low Solidity Cascade Diffuser

A single-stage transonic centrifugal compressor with a pressure ratio greater than six was tested in a closed loop with HFC134a gas. Flow at the inducer of a rotating impeller as well as flow in a stationary low-solidity cascade diffuser was measured using a double-pulse and double-frame particle image velocimetry (PIV). Shock waves in both flows were clearly observed. The effect of flow rate on a 3D configuration of shock wave at the inducer and a so-called rotor-stator interaction between a rotating impeller and a stationary cascade were discussed based on a phase-averaged measurement technique. Furthermore, the unsteadiness of inducer shock wave and the flow in a cascade diffuser during surge were discussed based on instantaneous velocity vector maps.

Application of a Low-Solidity Cascade Diffuser to Transonic Centrifugal Compressor

1990 ◽  
Vol 112 (1) ◽  
pp. 25-29 ◽  
Author(s):  
H. Hayami ◽  
Y. Senoo ◽  
K. Utsunomiya
Keyword(s):  
Centrifugal Compressor ◽  
Performance Test ◽  
Pressure Ratio ◽  
Test Results ◽  
Vaneless Diffuser ◽  
Circular Arc ◽  
Transonic Centrifugal Compressor ◽  
Wide Range ◽  
Compressor Performance ◽  
Low Solidity Cascade Diffuser

Low-solidity circular cascades, conformally transformed from high-stagger linear cascades of double-circular-arc vanes with solidity 0.69, were used as a part of the diffuser system of a transonic centrifugal compressor. Performance test results were compared with data of the same compressor with a vaneless diffuser. Good compressor performance and a wider flow range as well as a higher pressure ratio and a higher efficiency, superior to those with a vaneless diffuser, where the flow range was limited by choke of the impeller, were demonstrated. The test circular cascade diffusers demonstrated a good pressure recovery over a wide range of flow angles, even when the inflow Mach number to the cascade was over unity.

510 Analysis of Flow Behavior in a Transonic Centrifugal Compressor with Low Solidity Cascade Diffuser

2010 ◽  
Vol 2010.63 (0) ◽  
pp. 177-178
Author(s):  
Yohei SASAKI ◽  
Daisaku SAKAGUCHI ◽  
Masahiro ISHIDA ◽  
Hironobu UEKI ◽  
Hiroshi HAYAMI
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Transonic Centrifugal Compressor ◽  
Low Solidity Cascade Diffuser

Improvement of the Flow Range of Transonic Centrifugal Compressors With a Low-Solidity Cascade Diffuser

2000 ◽  
Author(s):  
Hiroshi Hayami
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Input Power ◽  
Velocity Of Sound ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Transonic Centrifugal Compressor ◽  
Series Of Experiments ◽  
Low Solidity Cascade Diffuser

If the pressure ratio of a typical single-stage centrifugal compressor is larger than four, the velocity relative to the impeller and to the diffuser exceeds the velocity of sound. The flow range of transonic centrifugal compressors with a vaned diffuser is usually very narrow. Low-solidity cascade diffusers with solidity 0.69 have been successfully applied as a part of the diffuser system of a transonic centrifugal compressor. On the basis of this type of diffuser, a series of experiments to broaden the operating range are discussed focusing on the control of the geometry of impeller and/or diffuser; one was to reduce the inducer blade turning upstream of the throat, and the other was to reduce the inlet passage width of diffuser. The milder inducer blade camber realized the improvement in flow range by 1.5 times to the original one. Regarding the diffuser inlet passage width contraction, the flow range was not broadened so much owing to the change in impeller characteristics, but the input power was reduced and then the high speed efficiency was much improved.

Application of Low-Solidity Cascade Diffuser to Transonic Centrifugal Compressor

1989 ◽  
Author(s):  
H. Hayami ◽  
Y. Senoo ◽  
K. Utsunomiya
Keyword(s):  
Centrifugal Compressor ◽  
Performance Test ◽  
Pressure Ratio ◽  
Test Results ◽  
Vaneless Diffuser ◽  
Circular Arc ◽  
Transonic Centrifugal Compressor ◽  
Wide Range ◽  
Compressor Performance ◽  
Low Solidity Cascade Diffuser

Low-solidity circular cascades, conformally transformed from high-stagger linear cascades of double-circular-arc vanes with solidity 0.69, were used as a part of the diffuser system of a transonic centrifugal compressor. Performance test results were compared with data of the same compressor with a vaneless diffuser. Good compressor performance, a wider flow range as well as a higher pressure ratio and a higher efficiency, superior to those with a vaneless diffuser, where the flow range was limited by choke of the impeller, were demonstrated. The test circular cascade diffusers demonstrated a good pressure recovery over a wide range of flow angles, even when the inflow Mach number to the cascade was over unity.

scholarly journals Comparison of Two Diffusers in a Transonic Centrifugal Compressor

2003 ◽  
Vol 9 (4) ◽  
pp. 279-284 ◽  
Author(s):  
Koji Nakagawa ◽  
Hiroshi Hayami ◽  
Yuichi Keimi
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Compressor ◽  
Flow Separation ◽  
Pressure Ratio ◽  
Maximum Pressure ◽  
Vaned Diffuser ◽  
Transonic Centrifugal Compressor ◽  
Flow Mechanisms ◽  
Series Of Experiments ◽  
Low Solidity Cascade Diffuser

Flow mechanisms suppressing the flow separation in two diffusers, a low-solidity cascade diffuser and a vaned diffuser with additional small vanes near the inlet, were compared mainly by numerical simulation. As the superiority of the low-solidity cascade diffuser was expected, a series of experiments was conducted using a transonic centrifugal compressor with a maximum pressure ratio of 7. The performance of the compressor with the vaned diffuser was comparable to that of the low-solidity cascade diffuser only between the surge point and the design flowrate at a pressure ratio of 3.5. The maximum flowrate of the vaned diffuser was lower than that of the low-solidity cascade diffuser. At higher rotational speeds, the pressure ratio at the surge point, the efficiency, and the flow range of the low-solidity cascade diffuser exceded those of a vaned diffuser at a pressure ratio of 3.5.

Experimental Investigation of Surge Phenomena in a Transonic Centrifugal Compressor With Inlet Distortion

2020 ◽  
Author(s):  
Sasuga Ito ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Takafumi Ota ◽  
Kazuhito Konishi ◽  
...  
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Flow Instability ◽  
Pressure Sensors ◽  
Low Flow ◽  
Inlet Distortion ◽  
Transonic Centrifugal Compressor ◽  
Response Pressure ◽  
Surge Phenomena ◽  
Low Flow Rate

Abstract Inlet distortion has influence on the aerodynamic performance of turbomachinery such as compressors, turbines and fans. On turbochargers, bent pipes are installed around the compressor due to the spatial limitations in the engine room of the vehicle. As the result, the compressor is operated with the distorted inflow. In the low flow rate operation, the distorted inflow also affects the flow instability like stall and surge. Especially, the operation range on the low flow rate side is defined based on the flow rate where surge occurs, so it is important to investigate the effect of the distorted inflow on surge. In this study, the effect of the inlet distortion to surge phenomena has been investigated by the experiments with a transonic centrifugal compressor. A bent pipe has been installed at the upstream of the compressor to generate a distorted flow. Experiments have been also conducted under the condition that a straight pipe was installed upstream of the compressor, and unsteady measurements with high response pressure sensors and an I-type hot wire probe have been carried out to each experiments. In addition, Fast Fourier transform (FFT) and Wavelet transform have been applied to the unsteady measurement results obtained from each experiment.

Influences of Tip Leakage Flows Discharged From Main and Splitter Blades on Flow Field in Transonic Centrifugal Compressor Stage

2018 ◽  
Author(s):  
Masanao Kaneko ◽  
Hoshio Tsujita
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Blade Loading ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Leakage Flows ◽  
Transonic Centrifugal Compressor ◽  
Tip Leakage Flows

A transonic centrifugal compressor impeller is generally composed of the main and the splitter blades which are different in chord length. As a result, the tip leakage flows from the main and the splitter blades interact with each other and then complicate the flow field in the compressor. In this study, in order to clarify the individual influences of these leakage flows on the flow field in the transonic centrifugal compressor stage at near-choke to near-stall condition, the flows in the compressor at four conditions prescribed by the presence and the absence of the tip clearances were analyzed numerically. The computed results clarified the following noticeable phenomena. The tip clearance of the main blade induces the tip leakage vortex from the leading edge of the main blade. This vortex decreases the blade loading of the main blade to the negative value by the increase of the flow acceleration along the suction surface of the splitter blade, and consequently induces the tip leakage vortex caused by the negative blade loading of the main blade at any operating points. These phenomena decline the impeller efficiency. On the other hand, the tip clearance of the splitter blade decreases the afore mentioned acceleration by the formation of the tip leakage vortex from the leading edge of the splitter blade and the decrease of the incidence angle for the splitter blade caused by the suction of the flow into the tip clearance. These phenomena reduce the loss generated by the negative blade loading of the main blade and consequently reduce the decline of the impeller efficiency. Moreover, the tip clearances enlarge the flow separation around the diffuser inlet and then decline the diffuser performance independently of the operating points.

Sign in / Sign up

Export Citation Format

Share Document