scholarly journals Experimental and numerical evaluations of composite concrete-to-concrete interfacial shear strength under horizontal and normal stresses

PLoS ONE ◽  
2021 ◽  
Vol 16 (5) ◽  
pp. e0252050
Author(s):  
M. Yahya Al-Fasih ◽  
M. E. Mohamad ◽  
I. S. Ibrahim ◽  
Y. Ahmad ◽  
M. A. Mohd Ariffin ◽  
...  
Keyword(s):  
Shear Strength ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Zone Model ◽  
Normal Stresses ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Surface Textures ◽  
Roughened Surface

Effects of different surface textures on the interface shear strength, interface slip, and failure modes of the concrete-to-concrete bond are examined through finite element numerical model and experimental methods in the presence of the horizontal load with ‘push-off’ technique under different normal stresses. Three different surface textures are considered; smooth, indented, and transversely roughened to finish the top surfaces of the concrete bases. In the three-dimensional modeling via the ABAQUS solver, the Cohesive Zone Model (CZM) is used to simulate the interface shear failure. It is observed that the interface shear strength increases with the applied normal stress. The transversely roughened surface achieves the highest interface shear strength compared with those finished with the indented and smooth approaches. The smooth and indented surfaces are controlled by the adhesive failure mode while the transversely roughened surface is dominated by the cohesive failure mode. Also, it is observed that the CZM approach can accurately model the interface shear failure with 3–29% differences between the modeled and the experimental test findings.

Some Observations on Soil-Pipe Interface Shear Strength in Direct Shear Under Low Effective Normal Stresses and Large Displacements

2016 ◽  
Author(s):  
Ruslan S. Amarasinghe ◽  
Dharma Wijewickreme ◽  
Hisham T. Eid
Keyword(s):  
Shear Strength ◽  
Accurate Determination ◽  
Direct Shear ◽  
Normal Stresses ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Fine Grained ◽  
Direct Shear Tests ◽  
Macro Scale ◽  
Soil Pipe

Experimental work is undertaken at the University of British Columbia (UBC) to study the soil-pipe interface shear strength at levels of shear displacements and effective normal stresses typically encountered in offshore soil-pipe interaction problems. A macro-scale interface direct shear apparatus having a test specimen footprint of 1.72 m × 1.75 m was designed and built for this purpose. The apparatus is capable of testing various soil-pipe interfaces under effective normal stresses in the range of 3 kPa to 6 kPa. A maximum shear displacement of 1.2 m is achievable at rates ranging from 0.1 μm/s to 1 mm/s. Sensors mounted at the interface enable the accurate determination of the effective normal stress at the interface when fully saturated fine-grained soils are tested. This paper presents some observations arising from a series of interface direct shear tests involving fine-grained soils of different plasticity against bare and epoxy coated steel surfaces.

INTERFACE SHEAR STRENGTH OF CONCRETE-TO-CONCRETE BOND WITH AND WITHOUT PROJECTING STEEL REINFORCEMENT

2015 ◽  
Vol 75 (1) ◽  
Author(s):  
Mazizah Ezdiani Mohamad ◽  
Izni Syahrizal Ibrahim
Keyword(s):  
Shear Strength ◽  
Steel Reinforcement ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Surface Textures ◽  
Concrete Base ◽  
Dowel Action ◽  
Eurocode 2 ◽  
Wire Brushing ◽  
The One

Composite concrete consists of two elements cast at different times which are the concrete base and concrete topping. To achieve composite action, interface shear strength must be sufficient to resist the sliding motion between the two concrete surfaces in contact. The interface shear strength is mainly depended on concrete cohesion, friction and dowel action. A total of 36 “push-off” tests were performed to study the interface shear strength and to assess the influence of surface texture and steel reinforcement crossing the interface. Three different concrete base surfaces are prepared which include smooth or “left as-cast”, roughened by wire-brushing in the transverse direction and steel reinforcement projecting from the concrete base. Eurocode 2 provides design equations for determining the interface shear strength with different surface textures and also the one where projecting steel reinforcement crosses the interface. The experimental results show that the transverse roughened surface produced the highest interface shear strength of 1.89 N/mm2 (σn = 0 N/mm2), 4.69 N/mm2 (σn = 0.5 N/mm2), 5.97 N/mm2 (σn = 1.0 N/mm2) and 6.42 N/mm2 (σn = 1.5 N/mm2) compared with the other surface textures. This proves that the increase in the degree of roughness contributes to higher concrete cohesion and friction coefficient. However, for the surface with projecting steel reinforcement, the failure is not sudden as experienced by the surface without one. This is due to the contribution of the clamping stress from the dowel action of the steel reinforcements. Meanwhile, for specimens without any projecting steel reinforcements, the interface shear strength depended solely on friction and concrete cohesion of the surface textures. The interface shear strength of surface with and without the projecting steel reinforcement can be predicted using the Mohr-Coulomb failure envelope. This paper also proposed design expressions for concrete-to-concrete bond on surfaces provided with and without projecting steel reinforcement that can be adopted in Eurocode 2.

scholarly journals Influence of Bond Behaviour of Flexural GFRP Reinforcement on Failure Mechanisms in Beams Without Stirrups

2018 ◽  
Vol 64 (4) ◽  
pp. 269-283
Author(s):  
M. Kaszubska ◽  
R. Kotynia
Keyword(s):  
Shear Strength ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Shear Crack ◽  
Failure Mechanisms ◽  
Crack Pattern ◽  
Critical Crack ◽  
Bond Behaviour ◽  
Gfrp Bars

AbstractThe aim of the paper is to investigate the shear failure mechanisms in T-shape, single span and simply supported beams exclusively reinforced with longitudinal glass fiber reinforced polymer (GFRP) bars. Usually the critical shear crack in RC beams without stirrups develops through the theoretical compression strut reducing the shear strength following the shear failure. The main parameter affecting the crack pattern and the shear strength of the beams is the shear slenderness. However, the test results presented in the paper indicated the new arching effect due to the bond losing between the GFRP flexural reinforcement and concrete. This failure mode revealed unexpected critical crack pattern and failure mode. The research of concrete beams flexurally reinforced with GFRP bars without stirrups indicated two failure modes: typical shear-compression and a new one leading by the bond losing between the ordinary reinforcement and concrete.

Influence of revision arthroplasty on bone/cement interface shear strength

1987 ◽  
Vol 20 (8) ◽  
pp. 824
Author(s):  
J.E. Bechtold ◽  
Y. Dohmae ◽  
R.E. Sherman ◽  
R.B. Gustilo
Keyword(s):  
Shear Strength ◽  
Bone Cement ◽  
Revision Arthroplasty ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Cement Interface

scholarly journals Skewness and Kurtosis: Important Parameters in the Characterization of Dental Implant Surface Roughness—A Computer Simulation

2011 ◽  
Vol 2011 ◽  
pp. 1-6 ◽  
Author(s):  
Karl Niklas Hansson ◽  
Stig Hansson
Keyword(s):  
Surface Roughness ◽  
Shear Strength ◽  
Roughness Parameter ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Implant Surface ◽  
Bone Response ◽  
Dental Implant Surface ◽  
Skewness And Kurtosis

The surface roughness affects the bone response to dental implants. A primary aim of the roughness is to increase the bone-implant interface shear strength. Surface roughness is generally characterized by means of surface roughness parameters. It was demonstrated that the normally used parameters cannot discriminate between surfaces expected to give a high interface shear strength from surfaces expected to give a low interface shear strength. It was further demonstrated that the skewness parameter can do this discrimination. A problem with this parameter is that it is sensitive to isolated peaks and valleys. Another roughness parameter which on theoretical grounds can be supposed to give valuable information on the quality of a rough surface is kurtosis. This parameter is also sensitive to isolated peaks and valleys. An implant surface was assumed to have a fairly well-defined and homogenous “semiperiodic” surface roughness upon which isolated peaks were superimposed. In a computerized simulation, it was demonstrated that by using small sampling lengths during measurement, it should be possible to get accurate values of the skewness and kurtosis parameters.

Residual shear strength of fine-grained soils and soil–solid interfaces at low effective normal stresses

2015 ◽  
Vol 52 (2) ◽  
pp. 198-210 ◽  
Author(s):  
Hisham T. Eid ◽  
Ruslan S. Amarasinghe ◽  
Khaled H. Rabie ◽  
Dharma Wijewickreme
Keyword(s):  
Shear Strength ◽  
Large Strain ◽  
Laboratory Research ◽  
Normal Stresses ◽  
Interface Shear ◽  
Residual Shear Strength ◽  
Fine Grained ◽  
Solid Interface ◽  
Wide Range ◽  
Shear Area

A laboratory research program was undertaken to study the large-strain shear strength characteristics of fine-grained soils under low effective normal stresses (∼3–7 kPa). Soils that cover a wide range of plasticity and composition were utilized in the program. The interface shear strength of these soils against a number of solid surfaces having different roughness was also investigated at similar low effective normal stress levels. The findings contribute to advancing the knowledge of the parameters needed for the design of pipelines placed on sea beds and the stability analysis of shallow soil slopes. A Bromhead-type torsional ring-shear apparatus was modified to suit measuring soil–soil and soil–solid interface residual shear strengths at the low effective normal stresses. In consideration of increasing the accuracy of assessment and depicting the full-scale field behavior, the interface residual shear strengths were also measured using a macroscale interface direct shear device with a plan interface shear area of ∼3.0 m2. Correlations are developed to estimate the soil–soil and soil–solid interface residual shear strengths at low effective normal stresses. The correlations are compared with soil–soil and soil–solid interface drained residual shear strengths and correlations presented in the literature.

Machine learning-based failure mode identification of RCSPSW

2021 ◽  
Author(s):  
Dongqi Jiang ◽  
Shanquan Liu ◽  
Tao Chen ◽  
Gang Bi
Keyword(s):  
Machine Learning ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Tall Buildings ◽  
Shear Walls ◽  
Superior Performance ◽  
Ann Model ◽  
Mode Recognition ◽  
Wide Range

<p>Reinforced concrete – steel plate composite shear walls (RCSPSW) have attracted great interests in the construction of tall buildings. From the perspective of life-cycle maintenance, the failure mode recognition is critical in determining the post-earthquake recovery strategies. This paper presents a comprehensive study on a wide range of existing experimental tests and develops a unique library of 17 parameters that affects RCSPSW’s failure modes. A total of 127 specimens are compiled and three types of failure modes are considered: flexure, shear and flexure-shear failure modes. Various machine learning (ML) techniques such as decision trees, random forests (RF), <i>K</i>-nearest neighbours and artificial neural network (ANN) are adopted to identify the failure mode of RCSPSW. RF and ANN algorithm show superior performance as compared to other ML approaches. In Particular, ANN model with one hidden layer and 10 neurons is sufficient for failure mode recognition of RCSPSW.</p>

scholarly journals An Experimental Study on Mechanical Behavior of Parallel Joint Specimens under Compression Shear

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Fei Wang ◽  
Ping Cao ◽  
Yu Chen ◽  
Qing-peng Gao ◽  
Zhu Wang
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Failure Mode ◽  
Shear Failure ◽  
Strain Curve ◽  
Shear Loading ◽  
Plane Shear ◽  
Joint Spacing ◽  
Dip Angle ◽  
Joint Inclination

In order to investigate the influence of the joint on the failure mode, peak shear strength, and shear stress-strain curve of rock mass, the compression shear test loading on the parallel jointed specimens was carried out, and the acoustic emission system was used to monitor the loading process. The joint spacing and joint overlap were varied to alter the relative positions of parallel joints in geometry. Under compression-shear loading, the failure mode of the joint specimen can be classified into four types: coplanar shear failure, shear failure along the joint plane, shear failure along the shear stress plane, and similar integrity shear failure. The joint dip angle has a decisive effect on the failure mode of the specimen. The joint overlap affects the crack development of the specimen but does not change the failure mode of the specimen. The joint spacing can change the failure mode of the specimen. The shear strength of the specimen firstly increases and then decreases with the increase of the dip angle and reaches the maximum at 45°. The shear strength decreases with the increase of the joint overlap and increases with the increase of the joint spacing. The shear stress-displacement curves of different joint inclination samples have differences which mainly reflect in the postrupture stage. From monitoring results of the AE system, the variation regular of the AE count corresponds to the failure mode, and the peak value of the AE count decreases with the increase of joint overlap and increases with the increase of joint spacing.

Sign in / Sign up

Export Citation Format

Share Document