EFFECT OF CFRP STRIPS BONDING LOCATION ON FLEXURAL CAPACITY AND DUCTILITY OF REINFORCED CONCRETE BEAMS

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Mina Iskander ◽  
Mina Melad ◽  
Mourad Yasser ◽  
Waleed Abdel Rahim ◽  
Amr Mosa ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Cross Sections ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Traditional Methods ◽  
Flexural Strengthening ◽  
Advanced Composite ◽  
Advanced Composite Materials ◽  
The Impact ◽  
Strength And Ductility

Strengthening reinforced concrete beams using laminate of advanced composite materials has gained ground recently due to its lower cost and simplicity compared to traditional methods. These traditional methods are usually done by either increasing the reinforcement or the beam’s dimensions, which naturally requires formwork, and hinder the structural usage. One of the most impediments of using bonded laminate in strengthening beams is debonding. In flexural strengthening of beams, this debonding occurs via mid-span debonding or end-delamination of the laminate. Herein, ten RC beams were experimentally tested in flexure under three-point loading. The reinforced concrete beams have rectangular cross sections and were strengthened by bonded CFRP strips. Flexural strength and ductility were investigated in order to reveal the impact of changing the CFRP strips’ locations with respect to the beams’ cross section. The CFRP strips were attached to the reinforced concrete beams sides of bottoms. The first configuration is thought to reduce the effect of flexure cracks in the mid-span of the beams, which may delay the deboning of these laminates. In order to anchor the strips, close to the support and eliminate end delamination, CFRP sheets were wrapped at these locations. Based on the proposed configurations, the flexure strength of the beams increased by an average of 40%.

scholarly journals Initial crack effect on the strength of oblique cross sections of reinforced concrete beams strengthened with carbon fiber

2019 ◽  
Vol 110 ◽  
pp. 01053
Author(s):  
Alexandr Shilov ◽  
Petr Polskoy ◽  
Dmitriy Mailyan ◽  
Petr Shilov
Keyword(s):  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Cross Sections ◽  
Structural Damage ◽  
Concrete Beams ◽  
Experimental Studies ◽  
Reinforced Concrete Beams ◽  
Shear Span ◽  
The Impact ◽  
Initial Cracks

In the theory of reinforced concrete, the issue on strength of the oblique beam sections is more complicated than that on the standard sections, since it depends on many factors. The change of at least one of them leads to a significant change in the carrying capacity and in the structural damage pattern. This is due to the fact that at the operating level of the load, all conventional reinforced concrete structures work with cracks, which must be considered in the calculation. However, in the existing regulatory documents and public sources, this issue is not specified. This paper considers the effect of initial cracks on the strength of oblique cross sections of the reinforced concrete beams strengthened with carbon fiber. The experimental studies results obtained through the transverse force testing of forty-two prototypes made of heavy concrete of B30 design grade are presented. The test samples had initial oblique cracks of 0.6-0.9 mm width and were reinforced with three composite U stirrups from the fabric based on unidirectional carbon fibers in the shear span. Initial cracks in the beams were formed at three values of the shear span – 1.5h0, 2h0 and 2.5h0. The test data show the impact of initial cracks on the efficiency of composite reinforcement of oblique cross sections of the prototypes at various values of shear spans.

scholarly journals RETROFITTING AND DACTILITY OF REINFORCED CONCRETE BEAMS USING AN EXTERNAL REINFORCEMENT METHOD

2019 ◽  
Vol 3 (2) ◽  
pp. 135
Author(s):  
Novita Ike Triyuliani ◽  
Sri Murni Dewi ◽  
Lilya Susanti
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Concrete Block ◽  
Steel Reinforcement ◽  
Reinforced Concrete Beams ◽  
Building Structures ◽  
Average Increase ◽  
External Reinforcement ◽  
Strength And Ductility

The innovations strengthening building structures are important topics. Failure in structures such as beams and columns due to time, re-functions of a building, even initial design errors that are weak or lack the safety factor of a building structure. External reinforced concrete beams are one of the beams currently being developed. It is a concrete block with reinforcement of steel reinforcement on the outer (external) of the beam. This study aims to determine the index of increasing beam strength and ductility after retrofitting external steel reinforcement, which has the dimension of beams 15 x 15 x 100 cm, repeating 12 pcs, with external reinforcement each 6 pcs 2Ø6 and 3Ø6. The results from this study are an increasing the index of beam flexural strength after retrofit with external steel reinforcement. Meanwhile, beams after retrofit with 2Ø6 external steel have an average increase index of 1.25 and 1.21 while for external steel 3Ø6 are 1.29 and 1.60 respectively. The ductility depends on the value of ultimate load and maximum deflection that occurs, where the ductility value for the comparison of each specimen experiences a reduction in the average ductility value with 2Ø6 external steel which is 37.74% and 70.95% while with 3Ø6 external steel is 61,65% and 60.62%. Berbagai inovasi upaya peningkatan kekuatan struktur bangunan telah menjadi bahasan yang penting. Kegagalan pada struktur seperti balok dan kolom karena umur, alih fungsi suatu bangunan, bahkan kesalahan desain awal yang lemah atau kurang memenuhi faktor keamanan suatu struktur bangunan. Balok beton bertulangan eksternal adalah salah satu balok yang sedang dikembangkan pada saat ini, yaitu balok beton dengan perkuatan tulangan baja di sisi terluar (eksternal). Penelitian ini bertujuan untuk mengetahui indeks peningkatan kekuatan balok dan daktilitas setelah dilakukan perbaikan menggunakan tulangan baja eksternal, dengan dimensi balok 15 × 15 × 100 cm berulang 12 buah, penambahan tulangan baja eksternal masingmasing 6 buah 2Ø6 dan 3Ø6. Hasil yang didapat dari penelitian ini adalah indeks peningkatan kekuatan lentur balok setelah dilakukan perbaikan menggunakan tulangan baja eksternal. Dimana balok setelah dilakukan perbaikan dengan baja eksternal 2Ø6 memiliki indeks peningkatan rata-rata 1,25 dan 1,21 sedangkan untuk baja eksternal 3Ø6 masing-masing 1,29 dan 1,60. Daktilitas tergantung dari nilai beban ultimit dan lendutan maksimum yang terjadi, dimana nilai daktilitas untuk perbandingan tiap benda uji mengalami reduksi nilai daktilitas rata-rata dengan baja eksternal 2Ø6 yaitu sebesar 37,74% dan 70,95% sedangkan dengan baja eksternal 3Ø6 sebesar 61,65% dan 60,62%.

scholarly journals DUCTILITY RESPONSE OF HYBRID FIBRE REINFORCED CONCRETE BEAMS

2018 ◽  
pp. 174-179 ◽  
Author(s):  
Eswari Natarajan
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Volume Fraction ◽  
Fibre Volume ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforced Concrete ◽  
Hybrid Fibre ◽  
Service Load ◽  
Strength And Ductility

Abstract: The effect of fibre content on the Strength and ductility behaviour of hybrid fibre reinforced concrete (HFRC) beams having different fibre volume fractions was investigated. The parameters of this investigation included service load, ultimate load, service load deflection, ultimate load deflection, crack width, deflection ductility and energy ductility. The fibre volume fraction (Vf) ranged from 0.0 to 2.0 percent. Steel and polyolefin fibres were combined in different proportions and their impact on the above parameters was studied. The ductile response of hybrid fibre reinforced concrete beams was compared with that of control beam. The test results show that addition of 2.0 percent by volume of hybrid fibres improve the strength and ductility appreciably. Empirical expressions for predicting the strength and ductility of hybrid fibre reinforced concrete (HFRC) are proposed based on regression analysis. A close agreement has been obtained between the predicted and experimental results.

Effect of cracking localization on the structural ductility of normal strength and high strength reinforced concrete beams with steel fibers

2019 ◽  
Vol 10 (4) ◽  
pp. 457-469 ◽  
Author(s):  
Avraham N Dancygier ◽  
Yuri S Karinski
Keyword(s):  
Reinforced Concrete ◽  
Transition Point ◽  
Concrete Beams ◽  
High Strength ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Flexural Ductility ◽  
Ductility Ratio ◽  
The Impact

This article presents a study of cracking localization in normal and high strength concrete beams that include steel fibers and the influence of this localization on their structural ductility. It is shown that for a given fiber type and content, as the reinforcement ratio ρ decreases, the cracking localization level increases. The effect of ρ on the level of cracking localization is more pronounced for low amounts of conventional reinforcement. This range of conventional reinforcement ratio is typical of slabs and especially for the commonly thicker protective slabs. Examination of the effect of the reinforcement ratio on the flexural ductility shows that there exists a transition point below which the ductility ratio decreases with  ρ. This transition point is well above the minimum reinforcement ratio, which is required in design codes for plain reinforced concrete elements. Empirical analysis of the relation between cracking localization and ductility ratio shows that up to the same transition point, as cracking localization increases, the flexural ductility decreases. Findings of this study show that the positive effect of adding fibers on enhancing the impact resistance of slabs and beams is conflicted by their negative influence on reducing the structural ductility for low reinforcement ratios, which are typical of protective slabs.

Sign in / Sign up

Export Citation Format

Share Document