Constitutive Modeling for Tensile Behaviors of Ultra-high-strength-steel BR1500HS at Different Temperatures and Strain Rates

2015 ◽  
Vol 34 (5) ◽  
Author(s):  
Guo-Zheng Quan ◽  
Dong-sen Wu ◽  
An Mao ◽  
Yan-dong Zhang ◽  
Yu-feng Xia ◽  
...  
Keyword(s):  
Constitutive Modeling ◽  
High Strength Steel ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
High Strength ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Tensile Deformation Behavior ◽  
Ultra High Strength Steel ◽  
Different Temperatures

AbstractIn order to investigate the tensile deformation behavior of ultra-high-strength-steel BR1500HS, a series of isothermal tensile experiments were carried out in a temperature range of 1023˜1123 K and a strain rate range of 0.01˜10 s

The effect of strain rates on tensile deformation of ultrafine-grained copper

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744014
Author(s):  
M. Li ◽  
Q. W. Jiang
Keyword(s):  
Strain Rate ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Tensile Deformation ◽  
Strain Rates ◽  
Roll Bonding ◽  
Fracture Elongation ◽  
Tensile Deformation Behavior ◽  
Ultrafine Grained ◽  
Flow Stress Level

Tensile deformation behavior of ultrafine-grained (UFG) copper processed by accumulative roll-bonding (ARB) was studied under different strain rates at room temperature. It was found that the UFG copper under the strain rate of 10[Formula: see text] s[Formula: see text] led to a higher strength (higher flow stress level), flow stability (higher stress hardening rate) and fracture elongation. In the fracture surface of the sample appeared a large number of cleavage steps under the strain rate of 10[Formula: see text] s[Formula: see text], indicating a typical brittle fracture mode. When the strain rate is 10[Formula: see text] or 10[Formula: see text] s[Formula: see text], a great amount of dimples with few cleavage steps were observed, showing a transition from brittle to plastic deformation with increasing strain rate.

Hot deformation behavior of low carbon advanced high strength steel (AHSS) microalloyed with boron

2009 ◽  
Vol 1243 ◽  
Author(s):  
I. Mejía ◽  
S. González-Sala ◽  
J.M. Cabrera
Keyword(s):  
High Temperature ◽  
Deformation Behavior ◽  
True Strain ◽  
High Strength ◽  
Tensile Tests ◽  
Strain Rates ◽  
Low Carbon ◽  
Compression Tests ◽  
Advanced High Strength Steel ◽  
Different Temperatures

ABSTRACTThis research work deals the influence of boron content on the high temperature deformation behavior of a low carbon advanced high strength steel (AHSS). For this purpose high temperature tensile and compression tests are carried out at different temperatures and constant true strain rates by using an Instron testing machine equipped with a radiant cylindrical furnace. Tensile tests are carried out at different temperatures (650, 750, 800, 900 and 1000°C) at a constant true strain rate of 0.001 s-1. Uniaxial hot compression tests are also performed over a wide range of temperatures (950, 1000, 1050 and 1100°C) and constant true strain rates (10-3, 10-2 and 10-1 s-1). In general, experimental results of hot tensile tests show an improvement of the hot ductility of the AHSS microalloyed with boron, although poor ductility at low temperatures (650 and 750°C). The fracture surfaces of the AHSS tested at temperatures showing the higher ductility (800, 900 and 1000°C) indicate that the fracture mode is a result of ductile failure, whereas in the region of poor ductility the fracture mode is of the ductile-brittle type failure. On the other hand, experimental results of hot compression tests show that both peak stress and peak strain tend to decrease in the AHSS microalloyed with boron, which indicates that boron generates a sort of solid solution softening effect in similar a way to other interstitial alloying elements in steel. Likewise, hot flow curves of the AHSS microalloyed with boron show an acceleration of the onset of dynamic recrystallization (DRX) and a delay of the recrystallization kinetics. Results are discussed in terms of boron segregation towards austenitic grain boundaries and second phase particles precipitation during plastic deformation and cooling.

A Study on Tensile Deformation Behavior in Fe-Based Shape Memory Alloy by Rate Sensitive Transformation Kinetics Model

2016 ◽  
Vol 725 ◽  
pp. 77-81
Author(s):  
Anthony Budiaman ◽  
Kazuki Fujita ◽  
Takeshi Iwamoto
Keyword(s):  
Numerical Simulation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Rate Sensitivity ◽  
Kinetics Model ◽  
Strain Rates ◽  
Transformation Kinetics ◽  
Tensile Deformation Behavior

Fe-based shape memory alloy (Fe-SMA) shows a shape memory effect (SME) governed by forward and reverse stress-induced martensitic transformation (SIMT). Fe-SMA has been applied to joints and dampers utilized at various strain rates. To utilize Fe-SMA better, it is necessary to understand the mechanical properties in a wide range of strain rate. In previous study, the results of a tensile test at various strain rates show a rate-sensitivity, however, the mechanism of rate-sensitive tensile deformation behavior is still unclear. Thus, a numerical simulation using a transformation kinetics model is needed to clarify the mechanism. Some transformation kinetics models have been proposed, however, the rate sensitivity cannot be included. In this study, the rate sensitivity of volume fraction martensite is considered into the transformation kinetics model as an improvement of the past-proposed model. The numerical simulation of the uniaxial tensile test at various strain rates is performed to reproduce transformation behavior of the martensite phase. Then, the model is validated by comparing to the experimental results. Afterwards, the mechanism of rate-sensitive tensile deformation behavior of Fe-SMA is discussed.

Sign in / Sign up

Export Citation Format

Share Document