Estimating Entropy Generation Rate for Ballistic-Diffusive Phonon Transport Using Effective Thermal Conductivity

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Saad Bin Mansoor ◽  
Bekir S. Yilbas
Keyword(s):  
Thermal Conductivity ◽  
Effective Thermal Conductivity ◽  
Entropy Generation ◽  
Mathematical Formulation ◽  
Phonon Transport ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Film Material ◽  
Diffusive Regime ◽  
Low Dimensional

Abstract The entropy generation rate in a low dimensional film is formulated incorporating the heat flux and effective thermal conductivity of the film material. In the analysis, the mathematical formulation employed is kept the same as that used in the diffusive regime. However, the entropy generation rate is corrected by replacing the bulk thermal conductivity with an effective thermal conductivity evaluated from the Boltzmann equation. The entropy generation rate using the phonon distribution from the equation of phonon radiative transport in the film material is employed. The results show that both formulations result in a very close match for the entropy generation rates.

Thermal and Entropy generation analysis of magnetohydrodynamic tangent hyperbolic slip flow towards a stretching sheet

2021 ◽  
pp. 095440892110411
Author(s):  
Shafiq Ahmad ◽  
Zafar H Khan ◽  
Salman Zeb ◽  
Muhammad Hamid
Keyword(s):  
Thermal Conductivity ◽  
Entropy Generation ◽  
Slip Flow ◽  
Variable Thermal Conductivity ◽  
Weissenberg Number ◽  
Temperature Fields ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Bejan Number ◽  
Generation Model

This article examined the effects of boundary layer flow and heat transport of a two-dimensional incompressible magnetohydrodynamic tangent hyperbolic fluid under slip boundary conditions and variable thermal conductivity. The entropy generation model is also analysed for the said fluid. Non-similarity transformations transformed the governing equations of the fluid and entropy generation model into dimensionless form. Maple software is used to solve the transformed equations numerically. Effects of different dimensionless parameters on entropy generation rate, Bejan number, velocity and temperature fields are studied thoroughly through graphs. It is observed that for higher values of velocity slip parameter and power-law index, the entropy generation rate decreases while the Bejan number increases. Also, for the Hartmann number, Weissenberg number and Brinkman number, we found an increase in the entropy generation rate, and reverse behaviour is observed for the Bejan number. Nusselt number, temperature profile and Bejan’s number increase with an increase in variable thermal conductivity.

Analysis of the Effects of Joule Heating and Viscous Dissipation on Combined Pressure-Driven and Electrokinetic Flows in a Two-Parallel Plate Channel with Unequal Constant Temperatures

2018 ◽  
Vol 233 (4) ◽  
pp. 871-879 ◽  
Author(s):  
Harshad Sanjay Gaikwad ◽  
Pranab Kumar Mondal ◽  
Dipankar Narayan Basu ◽  
Nares Chimres ◽  
Somchai Wongwises
Keyword(s):  
Viscous Dissipation ◽  
Entropy Generation ◽  
Joule Heating ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Local Entropy ◽  
Temperature Dependent ◽  
Temperature Dependent Viscosity ◽  
Dependent Viscosity ◽  
Local Entropy Generation

In this article, we perform an entropy generation analysis for the micro channel heat sink applications where the flow of fluid is actuated by combined influences of applied pressure gradient and electric field under electrical double layer phenomenon. The upper and lower walls of the channels are kept at different constant temperatures. The temperature-dependent viscosity of the fluid is considered and hence the momentum equation and energy equations are coupled in this study. Also, a hydrodynamic slip condition is employed on the viscous dissipation. For complete analysis of the entropy generation, we use a perturbation approach with lubrication approximation. In this study, we discuss the results depicting variations in the velocity and temperature distributions and their effect on local entropy generation rate and Bejan number in the system. It can be summarized from this analysis that the enhanced velocity gradients in the flow field due to combined effect of temperature-dependent viscosity and Joule heating and viscous dissipative effects, leads to an enhancement in the local entropy generation rate in the system.

Aerodynamic Optimization Design of Airfoil Shape Using Entropy Generation as an Objective

2018 ◽  
Vol 11 (2) ◽  
Author(s):  
Wei Wang ◽  
Jun Wang ◽  
Xiao-Pei Yang ◽  
Yan-Yan Ding
Keyword(s):  
Entropy Generation ◽  
Energy Cost ◽  
Optimization Design ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Aerodynamic Optimization ◽  
Analysis And Design ◽  
Constraint Model ◽  
The Impact ◽  
Drag Ratio

Abstract An entropy analysis and design optimization methodology is combined with airfoil shape optimization to demonstrate the impact of entropy generation on aerodynamics designs. In the work herein, the entropy generation rate is presented as an extra design objective along with lift-drag ratio, while the lift coefficient is the constraint. Model equation, which calculates the local entropy generation rate in turbulent flows, is derived by extending the Reynolds-averaging of entropy balance equation. The class-shape function transform (CST) parametric method is used to model the airfoil configuration and combine the radial basis functions (RBFs) based mesh deformation technique with flow solver to compute the quantities such as lift-drag ratio and entropy generation at the design condition. From the multi-objective solutions which represent the best trade-offs between the design objectives, one can select a set of airfoil shapes with a low relative energy cost and with improved aerodynamic performance. It can be concluded that the methodology of entropy generation analysis is an effective tool in the aerodynamic optimization design of airfoil shape with the capability of determining the amount of energy cost.

The Role of Fin Geometry in Heat Sink Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 324-330 ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Generation Rate ◽  
Heat Transfer Fluid ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Axis Ratio

The following study will examine the effect on overall thermal/fluid performance associated with different fin geometries, including, rectangular plate fins as well as square, circular, and elliptical pin fins. The use of entropy generation minimization, EGM, allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including base plate and applying the conservations equations for mass and energy with the entropy balance. The formulation for the dimensionless entropy generation rate is developed in terms of dimensionless variables, including the aspect ratio, Reynolds number, Nusselt number, and the drag coefficient. Selected fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and Reynolds number. The results clearly indicate that the preferred fin profile is very dependent on these parameters.

Second-Law Analysis on Wavy Plate Fin-and-Tube Heat Exchangers

1998 ◽  
Vol 120 (3) ◽  
pp. 797-800 ◽  
Author(s):  
W. W. Lin ◽  
D. J. Lee
Keyword(s):  
Entropy Generation ◽  
Operating Conditions ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Second Law ◽  
Spanwise Direction ◽  
Minimum Entropy ◽  
Tube Heat Exchanger ◽  
Second Law Analysis ◽  
Minimum Entropy Generation

Second-law analysis on the herringbone wavy plate fin-and-tube heat exchanger was conducted on the basis of correlations of Nusselt number and friction factor proposed by Kim et al. (1997), from which the entropy generation rate was evaluated. Optimum Reynolds number and minimum entropy generation rate were found over different operating conditions. At a fixed heat duty, the in-line layout with a large tube spacing along streamwise direction was recommended. Furthermore, within the valid range of Kim et al.’s correlation, effects of the fin spacing and the tube spacing along spanwise direction on the second-law performance are insignificant.

scholarly journals Entropy Generation Rates in Two-Dimensional Rayleigh–Taylor Turbulence Mixing

Entropy ◽  
2018 ◽  
Vol 20 (10) ◽  
pp. 738 ◽  
Author(s):  
Xinyu Yang ◽  
Haijiang He ◽  
Jun Xu ◽  
Yikun Wei ◽  
Hua Zhang
Keyword(s):  
Time Evolution ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Two Dimensional ◽  
Spatial Averaging ◽  
Mixing Process ◽  
Thermal Entropy ◽  
Large Gradient ◽  
Turbulence Mixing

Entropy generation rates in two-dimensional Rayleigh–Taylor (RT) turbulence mixing are investigated by numerical calculation. We mainly focus on the behavior of thermal entropy generation and viscous entropy generation of global quantities with time evolution in Rayleigh–Taylor turbulence mixing. Our results mainly indicate that, with time evolution, the intense viscous entropy generation rate s u and the intense thermal entropy generation rate S θ occur in the large gradient of velocity and interfaces between hot and cold fluids in the RT mixing process. Furthermore, it is also noted that the mixed changing gradient of two quantities from the center of the region to both sides decrease as time evolves, and that the viscous entropy generation rate ⟨ S u ⟩ V and thermal entropy generation rate ⟨ S θ ⟩ V constantly increase with time evolution; the thermal entropy generation rate ⟨ S θ ⟩ V with time evolution always dominates in the entropy generation of the RT mixing region. It is further found that a “smooth” function ⟨ S u ⟩ V ∼ t 1 / 2 and a linear function ⟨ S θ ⟩ V ∼ t are achieved in the spatial averaging entropy generation of RT mixing process, respectively.

Entropy Analysis of the Nonlinear Convective Flow of a Jeffrey Fluid over an Inclined Sheet with Variable Electrical Conductivity and Thermal Conductivity

2021 ◽  
Vol 52 ◽  
pp. 73-91
Author(s):  
Jacob A. Gbadeyan ◽  
Joseph O. Akinremi
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Boundary Conditions ◽  
Entropy Generation ◽  
Convective Flow ◽  
Transverse Magnetic ◽  
Entropy Generation Rate ◽  
Jeffrey Fluid ◽  
Convective Boundary ◽  
Fourth Order Method

A steady two-dimensional nonlinear convective flow of a viscous, incompressible, electrically conducting, and non-Newtonian Jeffrey fluid over an inclined stretching sheet with convective boundary conditions and entropy generation is studied under the influence of transverse magnetic field, electrical conductivity and thermal conductivity. The thermal conductivity and electrical conductivity are temperature dependent functions. The governing continuity, momentum and energy equations are transformed to ordinary differential equations (ODEs) using appropriate similarity variables. The resulting coupled ODEs and the corresponding boundary conditions, are solved numerically using Runge-Kutta fourth order method and shooting technique. The velocity, entropy generation rate, temperature and Bejan distributions are presented graphically and discussed. The numerical values of the skin-friction and Nusselt number are obtained and also discussed for various thermophysical parameters through a Table. Furthermore, a comparison with earlier work done with limiting case was carried out and found to be in excellent agreement.

Thermodynamical Comparisons of Four Types of Regenerators in Cryocoolers

2012 ◽  
Vol 433-440 ◽  
pp. 1359-1365
Author(s):  
Yong Fei Guo ◽  
Hua Zhang ◽  
Xi Chen ◽  
Qiang Wang
Keyword(s):  
Entropy Generation ◽  
Process Model ◽  
Gas Flow ◽  
Irreversible Process ◽  
Unit Length ◽  
Generation Rate ◽  
Irreversible Processes ◽  
Entropy Generation Rate ◽  
Mesh Screen ◽  
The Matrix

Comparisons between the mesh screen, parallel wire, etched foil and sphere beds regenerators have been made base on the calculation of entropy generation rate per unit length in the four irreversible processes. The irreversible process model of heat conduction of gas and matrix, gas flow resistance and heat exchange between gas and matrix are respectively analyzed. Based on the software Regen3.3 user manual, the entropy generation rate per unit length are calculated and compared between the four regenerators. It is indicated that the irreversible processes loss in the cold end plays the key role in the whole regenerator, and it is an important way to improve the regeneration efficient by optimizing the matrix geometries and the material properties at the cold end.

Sign in / Sign up

Export Citation Format

Share Document