Strain Rate Sensitivity Effect Measured in 316 Steel by the Small Punch Testing Method

2018 ◽  
Vol 7 (1) ◽  
pp. 20180068
Author(s):  
F. Lowrie ◽  
M. Gorley ◽  
E. Surrey ◽  
B. Wynne ◽  
D. Wilkes
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Small Punch ◽  
Testing Method

scholarly journals Negative Strain Rate Sensitivity Induced by Structure Heterogeneity in Zr64.13Cu15.75Ni10.12Al10 Bulk Metallic Glass

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 339
Author(s):  
Xiang Wang ◽  
Zhi Qiang Ren ◽  
Wei Xiong ◽  
Si Nan Liu ◽  
Ying Liu ◽  
...  
Keyword(s):  
Metallic Glass ◽  
Strain Rate ◽  
Bulk Metallic Glass ◽  
Strain Rate Sensitivity ◽  
Critical Role ◽  
Rate Sensitivity ◽  
Confined Compression ◽  
Negative Strain Rate Sensitivity ◽  
Cast Specimen ◽  
Structure Heterogeneity

The negative strain rate sensitivity (SRS) of metallic glasses is frequently observed. However, the physical essence involved is still not well understood. In the present work, small-angle X-ray scattering (SAXS) and high-resolution transmission electron microscopy (HRTEM) reveal the strong structure heterogeneity at nanometer and tens of nanometer scales, respectively, in bulk metallic glass (BMG) Zr64.13Cu15.75Ni10.12Al10 subjected to fully confined compression processing. A transition of SRS of stress, from 0.012 in the as-cast specimen to −0.005 in compression processed specimen, was observed through nanoindentation. A qualitative formulation clarifies the critical role of internal stress induced by structural heterogeneity in this transition. It reveals the physical origin of this negative SRS frequently reported in structurally heterogeneous BMG alloys and its composites.

Strain rate sensitivity of a 1.5 GPa nanotwinned steel

2021 ◽  
Author(s):  
R.D. Liu ◽  
Y.Z. Li ◽  
L. Lin ◽  
C.P. Huang ◽  
Z.H. Cao ◽  
...  
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity

scholarly journals The Strain Rate Sensitivity and Creep Behavior for the Tripler Plane of Potassium Dihydrogen Phosphate Crystal by Nanoindentation

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 369
Author(s):  
Jianhui Mao ◽  
Wenjun Liu ◽  
Dongfang Li ◽  
Chenkai Zhang ◽  
Yi Ma
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Creep Deformation ◽  
Potassium Dihydrogen Phosphate ◽  
Rate Sensitivity ◽  
Dislocation Nucleation ◽  
Machining Process ◽  
Dihydrogen Phosphate ◽  
Potassium Dihydrogen ◽  
Kdp Crystals

As an excellent multifunctional single crystal, potassium dihydrogen phosphate (KDP) is a well-known, difficult-to-process material for its soft-brittle and deliquescent nature. The surface mechanical properties are critical to the machining process; however, the characteristics of deformation behavior for KDP crystals have not been well studied. In this work, the strain rate effect on hardness was investigated on the mechanically polished tripler plane of a KDP crystal relying on nanoindentation technology. By increasing the strain rate from 0.001 to 0.1 s−1, hardness increased from 1.67 to 2.07 GPa. Hence, the strain rate sensitivity was determined as 0.053, and the activation volume of dislocation nucleation was 169 Å3. Based on the constant load-holding method, creep deformation was studied at various holding depths at room temperature. Under the spherical tip, creep deformation could be greatly enhanced with increasing holding depth, which was mainly due to the enlarged holding strain. Under the self-similar Berkovich indenter, creep strain could be reduced at a deeper location. Such an indentation size effect on creep deformation was firstly reported for KDP crystals. The strain rate sensitivity of the steady-state creep flow was estimated, and the creep mechanism was qualitatively discussed.

Nanoindentation strain rate sensitivity of thermo-oxidized PMR-15 polyimide

2009 ◽  
Vol 44 (8) ◽  
pp. 2119-2127 ◽  
Author(s):  
Y. C. Lu ◽  
G. P. Tandon ◽  
S. Putthanarat ◽  
G. A. Schoeppner
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

Sign in / Sign up

Export Citation Format

Share Document