Effects of Heat Treatment on Mechanical Properties of Stainless Steel Wire

2017 ◽  
Vol 13 (4) ◽  
pp. 197-202
Author(s):  
Gyu-Sun Lee
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Stainless Steel ◽  
Steel Wire ◽  
Stainless Steel Wire

scholarly journals Effect of heat treatment on the mechanical properties of stainless steel wire

2021 ◽  
Vol 1942 (1) ◽  
pp. 012102
Author(s):  
M A Kaplan ◽  
A Yu Ivannikov ◽  
A D Gorbenko ◽  
A V Mikhailova ◽  
A A Kirsankin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Stainless Steel ◽  
Steel Wire ◽  
Stainless Steel Wire

Bending Properties of General Purpose Stainless Steel Wire Formed for Orthodontic Use

2013 ◽  
Vol 746 ◽  
pp. 394-399
Author(s):  
Niwat Anuwongnukroh ◽  
Yosdhorn Chuankrerkkul ◽  
Surachai Dechkunakorn ◽  
Pornkiat Churnjitapirom ◽  
Theeralaksna Suddhasthira
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Orthodontic Treatment ◽  
Steel Wire ◽  
General Purpose ◽  
Stainless Steel Wire ◽  
Bending Test ◽  
Bending Properties ◽  
Steel Wires ◽  
Significant Difference

The archwire is generally used in fixed appliances for orthodontic treatment to correct dental malocclusion. However, it is interesting to know whether general purpose stainless steel wire could replace commercial orthodontic archwire in orthodontic practice for economic reasons. The purpose of this study was to determine the bending properties of general purpose stainless steel wire compared with commercial orthodontic stainless steel wires after forming as an archwire for orthodontic use. The samples used in this study were 90 general purpose and 45 commercial (Highland) round stainless steel wires in 0.016, 0.018, and 0.020 sizes (30 general purpose and 15 commercial wires for each size). All 15 general purpose stainless steel wires with different sizes were formed into orthodontic archwire with a Universal Testing Machine. All samples were tested (three-point bending test) for mechanical properties. The results showed no significant difference between general purpose and commercial orthodontic wires in size 0.016 for 0.1 mm offset bending force, 0.2% yield strength, and springback. Although many mechanical properties of general purpose wires differed from commercial wires, their values conformed to other previous studies within the range of clinical acceptance. In conclusion, orthodontic formed general purpose round stainless steel wires had statistically different (p <0.05) mechanical properties from commercial orthodontic stainless steel wires (Highland) but the mechanical properties were acceptable to use in orthodontic treatment.

scholarly journals The Influence of heat treatment in orthodontic arches made of stainless steel wire

2000 ◽  
Vol 3 (3) ◽  
pp. 97-98 ◽  
Author(s):  
R.S. de Biasi ◽  
A.C.O. Ruela ◽  
C.N. Elias ◽  
O. Chevitarese
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Steel Wire ◽  
Stainless Steel Wire

Optimum Time and Temperature for Stress Relief Heat Treatment of Stainless Steel Wire

1973 ◽  
Vol 52 (6) ◽  
pp. 1171-1175 ◽  
Author(s):  
Michael R. Marcotte
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Steel Wire ◽  
Stress Relief ◽  
Stainless Steel Wire ◽  
Optimum Time ◽  
Dependent Variables

With the use of springback and recovery as dependent variables, the effects of time and temperature of stress relief heat treatment of stainless steel wire were studied. Stainless steel springs exposed to a stress relief heat treatment of 750 F for 11 minutes appear to have significantly improved spring properties.

scholarly journals Three Palatal Arches Used to Correct Posterior Dental Crossbites

2006 ◽  
Vol 76 (6) ◽  
pp. 1047-1051 ◽  
Author(s):  
Fernando Lima Martinelli ◽  
Priscilla Sobral Couto ◽  
Antonio Carlos Oliveira Ruellas
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Statistical Analysis ◽  
Orthodontic Treatment ◽  
Elasticity Modulus ◽  
Steel Wire ◽  
Testing Machine ◽  
Stainless Steel Wire ◽  
Quad Helix ◽  
One Way Anova

Abstract Objective: To assess the force, resilience, and elasticity modulus produced by the Coffin appliance, “W” arch, and quad-helix made with 0.032-inch and 0.036-inch stainless steel wire. Materials and Methods: Two groups of 15 arches were made as Coffin appliances, two groups of 15 arches were made as “W” arches, and two groups of 15 arches were made as quad-helices. One group of each appliance was formed in 0.032-inch and one group in 0.036-inch stainless steel wire. All arches (6 groups of 15 each) were submitted to compression trials in the mechanical testing machine EMIC DL-10000, simulating 5-, 8-, 10-, and 12-mm activation. The force and resilience means received a one-way ANOVA statistical analysis. Results: The results showed that the mechanical properties depended on the shape of the appliance, the diameter of the wire used, and the amount of activation. Conclusions: The three appliances assessed produce appropriate forces for orthodontic treatment as long as they are correctly planned during clinical application.

Sign in / Sign up

Export Citation Format

Share Document