scholarly journals Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts

2016 ◽  
Vol 36 (3) ◽  
pp. 110 ◽  
Author(s):  
Kenny Álvarez ◽  
Rodrigo F. Lagos ◽  
Miguel Aizpun
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fused Deposition Modeling ◽  
Tensile Force ◽  
Impact Resistance ◽  
Acrylonitrile Butadiene Styrene ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Time

3D printing is a manufacturing process that is usually used for modeling and prototyping. One of the most popular printing techniques is fused deposition modeling (FDM), which is based on adding melted material layer by layer. Although FDM has several advantages with respect to other manufacturing materials, there are several problems that have to be faced. When setting the printing options, several parameters have to be taken into account, such as temperature, speed, infill percentage, etc. Selecting these parameters is often a great challenge for the user, and is generally solved by experience without considering the influence of variations in the parameters on the mechanical properties of the printed parts.This article analyzes the influence of the infill percentage on the mechanical properties of ABS (Acrylonitrile Butadiene Styrene) printed parts. In order to characterize this influence, test specimens for tensile strength and Charpy tests were printed with a Makerbot Replicator 2X printer, in which the infill percentage was varied but the rest of the printing parameters were kept constant. Three different results were analyzed for these tests: tensile strength, impact resistance, and effective printing time. Results showed that the maximum tensile force (1438N) and tensile stress (34,57MPa) were obtained by using 100% infill. The maximum impact resistance, 1,55J, was also obtained with 100% infill. In terms of effective printing time, results showed that printing with an infill range between 50% and 98% is not recommended, since the effective printing time is higher than with a 100% infill and the tensile strength and impact resistance are smaller. In addition, in comparing the results of our analysis with results from other authors, it can be concluded that the printer type and plastic roll significantly influence the mechanical properties of ABS parts.

Quantitative strength analysis for 3D-printed specimens in a Tri-Hexagon pattern

2021 ◽  
pp. 095440622110211
Author(s):  
Sourabh Tandon ◽  
Ruchin Kacker ◽  
KG Sudhakar
Keyword(s):  
Tensile Strength ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Strength Properties ◽  
Strength Analysis ◽  
Layer By Layer ◽  
Sem Images ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Suitable Combination

ABS (Acrylonitrile Butadiene Styrene) and PLA (Polylactic acid) are the most commonly used thermoplastic materials in the AM (Additive Manufacturing) to build objects adding layer by layer. Addition of reinforcement such as carbon fibres to these materials is common to enhance strength properties. This work aims the fabrication of ABS, PLA, and PLA+CF specimens using the FDM (Fused Deposition Modeling). Subsequently, the tensile strength of printed specimens at Tri-Hexagon pattern for various % infills with different orientations is investigated. For a desired strength, the analysis facilitates the designer to choose suitable combination of specimen orientation at a specific infill and pattern. PLA+CF and ABS specimens with Tri-hexagon pattern at 0° orientation retain considerable strength when infill % gets lowered, whereas, virgin PLA observes higher strength stability at 90° orientation. The magnitudes of Ultimate tensile strength increased with infill %. The peak strength for PLA+CF specimen (with 100% infill without any pattern) at 0° and 90° orientation was 22% and 5% more, respectively, compared to 45° orientation. SEM images reveal a decrease in strength with ABS and PLA specimens due to the presence of voids between the layers, whereas showed strong bonding between CF and PLA matrix. Tri-Hexagon pattern showed better strength than the honeycomb, line, and rectilinear, especially at lower infills. Specimens both with and without Tri-hexagonal pattern observed superior ductile characteristics at 0° and 90° orientation, whereas most inferior at 45°.

Investigation of Recycled Acrylonitrile Butadiene Styrene for Additive Manufacturing

2020 ◽  
pp. 130-154
Author(s):  
Shajahan Bin Maidin ◽  
Zulkeflee Abdullah ◽  
Ting Kung Hieng
Keyword(s):  
Mechanical Properties ◽  
Test Specimen ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Travel Speed ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Processes ◽  
Butadiene Styrene

One of the disadvantages of fused deposition modeling (FDM) is waste produced during the printing processes. This investigation focuses on using 100% recycled Acrylonitrile Butadiene Styrene (ABS) for the FDM process. The recycling begins with re-granule the waste ABS material and produces it into a new filament. The new recycled filament was used to print the test specimen. Investigation on the mechanical properties and the surface quality of the test specimen and comparison with standard ABS specimen was done. The result shows that the recycled ABS can be produced into filament with 335°C of extrusion temperature and 1.5 mm/s travel speed of the extruder conveyor. The surface roughness of recycled specimen is 6.94% higher than the standard ABS specimen. For ultimate tensile strength, there is a small difference in X and Y orientation between the standard and the recycled ABS specimen which are 22.93% and 19.98%, respectively. However, in Z orientation, it is 52.33% lower. This investigation proves that ABS can be recycled without significantly affecting its mechanical properties.

Tensile Strength and Flexural Strength Testing of Acrylonitrile Butadiene Styrene (ABS) Materials for Biomimetic Robotic Applications

2014 ◽  
Vol 20 ◽  
pp. 11-21 ◽  
Author(s):  
Tran Linh Khuong ◽  
Zhao Gang ◽  
Muhammad Farid ◽  
Rao Yu ◽  
Zhuang Zhi Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Butadiene Styrene

Biomimetic robots borrow their structure, senses and behavior from animals, such as humans or insects, and plants. Biomimetic design is design ofa machine, a robot or a system in engineeringdomain thatmimics operational and/orbehavioral model of a biological system in nature. 3D printing technology has another name as rapid prototyping technology. Currently it is being developed fastly and widely and is applied in many fields like the jewelry, footwear, industrial design, architecture, engineering and construction, automotive, aerospace, dental and medical industry, education, geographic information system, civil engineering, guns. 3D printing technology is able to manufacture complicated, sophisticated details that the traditional processing method cannot manufacture. Therefore, 3D printing technology can be seen as an effective tool in biomimetic, which can accurately simulate most of the biological structure. Fused Deposition Modeling (FDM) is a technology of the typical rapid prototyping. The main content of the article is the focusing on tensile strength test of the ABS-Acrylonitrile Butadiene Styrene material after using Fused Deposition Modeling (FDM) technology, concretization after it’s printed by UP2! 3D printer. The article focuses on two basic features which are Tensile Strength and Determination of flexural properties.

Influence of Built Orientation on Mechanical Properties in Fused Deposition Modeling

2014 ◽  
Vol 592-594 ◽  
pp. 400-404 ◽  
Author(s):  
Sandeep V. Raut ◽  
Vijaykumar S. Jatti ◽  
T.P. Singh
Keyword(s):  
Mechanical Properties ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Polymer Materials ◽  
Manufacturing Cost ◽  
Layer By Layer ◽  
Total Cost ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Main Material

Fused deposition modeling (FDM) is one of the thirty techniques of rapid prototyping methods that produce prototypes from polymer materials (natural or with different grades). Acrylonitrile butadiene styrene (ABS) is one of the good material among all polymer materials. It is used in the layer by layer manufacturing of the prototype which is in the semi-molten plastic filament form and built up on the platform from bottom to top. In FDM, one of the critical factor is to select the built up orientation of the model since it affects the different areas of the model like main material, support material, built up time, total cost per part and most important the mechanical properties of the part. In view of this, objective of the present study was to investigate the effect of the built-up orientation on the mechanical properties and total cost of the FDM parts. Experiments were carried out on STRATASYS FDM type rapid prototyping machine coupled with CATALYST software and ABS as main material. Tensile and Impact specimens were prepared as per the ASTM standard with different built-up orientation and in three geometrical axes. It can be concluded from the experimental analysis that built orientation has significant affect on the tensile, impact and total cost of the FDM parts. These conclusions will help the design engineers to decide on proper build orientation, so that FDM parts can be fabricated with good mechanical properties at minimum manufacturing cost.

FDM Prototype Experimental Research of Processing Parameter Optimization to Achieve Higher Tensile Stress

2015 ◽  
Vol 220-221 ◽  
pp. 767-773 ◽  
Author(s):  
Ilmars Brensons ◽  
Svetlana Polukoshko ◽  
Andris Silins ◽  
Natalija Mozga
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
Rapid Prototype ◽  
Layer By Layer ◽  
Processing Parameter ◽  
Practical Applications ◽  
Fused Deposition

Fused Deposition Modeling (FDM) is one of most common ways of rapidly producing a part. Heated material (most commonly – plastic) is used to extrude it through a nozzle and deposit on a surface layer by layer until the part is fully produced. FDM has become one of the most popular in rapid production area due to its low cost, available materials and versatility.Due to fact that part is made layer by layer and each additional layer is deposited on top of a layer that is already a little below material melting point, part maintains different mechanical properties in various directions. These varying mechanical properties affect the part usability in practical applications. Critical point is tensile strength.The objective of this paper is to research optimal processing parameters for FDM prototyping to improve tensile strength. Several rapid prototype models (tensile test samples) with various geometry of longitudinal reinforcement channels were built. As reinforcing material, the epoxy resin was used, because it has higher tensile strength when solid and allows filling channels with various geometry. All made samples were tested for tensile strength. Experiment was carried out to confirm the effectiveness of this approach. From the results, it is found how different amount of epoxy resin affects part tensile strength.

scholarly journals Study of Different Printing Design Type Polymer Samples Prepared by Additive Manufacturing

2019 ◽  
Vol 64 (2) ◽  
pp. 255-264
Author(s):  
Lucie Zarybnicka ◽  
Karel Dvorak ◽  
Zdenka Dostalova ◽  
Hana Vojackova
Keyword(s):  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Maximum Load ◽  
3D Print ◽  
Fused Deposition ◽  
Bed Temperature ◽  
Deposition Modeling ◽  
Design Type ◽  
Butadiene Styrene

3D printing is one of the most progressive additive technologies today. It finds its application also in industry. In terms of mechanical properties, the printing design of the product is an important parameter. The presented study investigates the effects of the printing design of a thin-walled 3D polymer model on the mechanical properties of the model. The material used for printing was acrylonitrile-butadiene-styrene (ABS) and the 3D print method was Fused Deposition Modeling (FDM). ABS was tested at various die temperatures and with various printing designs at a constant 3D print speed and identical print bed temperature. We examined the effect of printing temperature and product printing design on the resulting mechanical properties. We compared theoretical and experimental results by CAE–FEM Advanced Simulation modules. Results tensile deformations at maximum load by experiment and simulations are comparable. The best results of testing the mechanical properties were found in the pattern printed at a 45° angle at temperature 285 °C.

Improvement in Tensile Strength of FDM Built Parts by Parametric Control

2014 ◽  
Vol 592-594 ◽  
pp. 1075-1079 ◽  
Author(s):  
Swayam Bikash Mishra ◽  
Siba Sankar Mahapatra
Keyword(s):  
Tensile Strength ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Optimal Parameter ◽  
Layer By Layer ◽  
3D Objects ◽  
Fused Deposition ◽  
Solid Models ◽  
Raster Angle ◽  
Deposition Modeling

Fused Deposition Modeling (FDM) is one of the efficient rapid prototyping (RP) technologies that forms 3D objects by adding material layer by layer from CAD generated solid models. However, the FDM built part is hardly anisotropic in nature due to layer-by-layer build mechanism. Literature suggests that mechanical property, especially tensile strength, of FDM built part is severely affected by process parameters. Among all the parameters, contour number happens to be an important parameter because it reduces stress concentration resulting in avoidance of premature breakdown. Therefore, in this work contour number along with five important process parameters such as layer thickness, raster width, part orientation, raster angle and air gap are considered and their effect on tensile strength of FDM built parts is studied. Experiments are conducted using Face Centred Central Composite Design (FCCCD) in order to reduce the experimental runs. An optimal parameter setting has been suggested for the maximisation of tensile strength of the FDM built parts.

scholarly journals Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

2020 ◽  
Vol 5 (1) ◽  
pp. 8
Author(s):  
Arivazhagan Selvam ◽  
Suresh Mayilswamy ◽  
Ruban Whenish ◽  
Rajkumar Velu ◽  
Bharath Subramanian
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Layer Thickness ◽  
Shell Thickness ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Thermoplastic Composites ◽  
Critical Parameters ◽  
Fused Deposition ◽  
Deposition Modeling

The most common method to fabricate both simple and complex structures in the additive manufacturing process is fused deposition modeling (FDM). Many researchers have studied the strengthening of FDM components by adding short carbon fibers (CF) or by reinforcing solid carbon fiber rods. In the current research, we sought to enhance the mechanical properties of FDM components by adding bioinspired solid CF rods during the fabrication process. An effective bonding interface of bioinspired CF rods and polylactic acid (PLA) was achieved by triangular interlocking sutures and by employing synthetic glue as the binding agent. In particular, the tensile strength of solid CF rod reinforced PLA samples was studied. Critical parameters such as layer thickness, extruder temperature, extruder speed, and shell thickness were considered for optimization. Significant process parameters were identified through leverage plots using the response surface methodology (RSM). The optimum parameters were found to be layer thickness of 0.04 mm, extruder temperature of 215 °C, extruder speed of 60 mm/s, and shell thickness of 1.2 mm. The results revealed that the bioinspired solid CF rod reinforced PLA (CFRPLA) composite exhibited a tensile strength of 82.06 MPa, which was approximately three times higher than the pure PLA (28 MPa, 66% lower than CFRPLA), acrylonitrile butadiene styrene (ABS) (28 MPa, 66% lower than CFRPLA), polyethylene terephthalate glycol (PETG) (34 MPa, 60% lower than CFRPLA), and nylon (34 MPa, 60% lower than CFRPLA) samples.

Sign in / Sign up

Export Citation Format

Share Document