scholarly journals Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

2020 ◽  
Vol 5 (1) ◽  
pp. 8
Author(s):  
Arivazhagan Selvam ◽  
Suresh Mayilswamy ◽  
Ruban Whenish ◽  
Rajkumar Velu ◽  
Bharath Subramanian
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Layer Thickness ◽  
Shell Thickness ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Thermoplastic Composites ◽  
Critical Parameters ◽  
Fused Deposition ◽  
Deposition Modeling

The most common method to fabricate both simple and complex structures in the additive manufacturing process is fused deposition modeling (FDM). Many researchers have studied the strengthening of FDM components by adding short carbon fibers (CF) or by reinforcing solid carbon fiber rods. In the current research, we sought to enhance the mechanical properties of FDM components by adding bioinspired solid CF rods during the fabrication process. An effective bonding interface of bioinspired CF rods and polylactic acid (PLA) was achieved by triangular interlocking sutures and by employing synthetic glue as the binding agent. In particular, the tensile strength of solid CF rod reinforced PLA samples was studied. Critical parameters such as layer thickness, extruder temperature, extruder speed, and shell thickness were considered for optimization. Significant process parameters were identified through leverage plots using the response surface methodology (RSM). The optimum parameters were found to be layer thickness of 0.04 mm, extruder temperature of 215 °C, extruder speed of 60 mm/s, and shell thickness of 1.2 mm. The results revealed that the bioinspired solid CF rod reinforced PLA (CFRPLA) composite exhibited a tensile strength of 82.06 MPa, which was approximately three times higher than the pure PLA (28 MPa, 66% lower than CFRPLA), acrylonitrile butadiene styrene (ABS) (28 MPa, 66% lower than CFRPLA), polyethylene terephthalate glycol (PETG) (34 MPa, 60% lower than CFRPLA), and nylon (34 MPa, 60% lower than CFRPLA) samples.

Linear model analysis of fused deposition modeling process parameters for obtaining the maximum tensile strength in acrylonitrile butadiene styrene (ABS) and carbon fiber polylactic acid (PLA) materials

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Debashis Mishra ◽  
Anil Kumar Das
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Layer Thickness ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Thermoplastic Material ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Speed

PurposeThe purpose of the experimental investigation was to optimize the process parameters of the fused deposition modeling (FDM) technique. The optimization of the process was performed to identify the relationship between the chosen factors and the tensile strength of acrylonitrile butadiene styrene (ABS) and carbon fiber polylactic acid (PLA) thermoplastic material, FDM printed specimens. The relationship was demonstrated by using the linear experimental model analysis, and a prediction expression was established. The developed prediction expression can be used for the prediction of tensile strength of selected thermoplastic materials at a 95% confidence level.Design/methodology/approachThe Taguchi L9 experimental methodology was used to plan the total number of experiments to be performed. The process parameters were chosen as three at three working levels. The working range of chosen factors was the printing speed (60, 80 and 100mm/min), 40%, 60% and 80% as the infill density and 0.1mm, 0.2mm and 0.3mm as the layer thickness. The fused deposition modeling process parameters were optimized to get the maximum tensile strength in FDM printed ABS and carbon fiber PLA thermoplastic material specimens.FindingsThe optimum condition was achieved by the process optimization, and the desired results were obtained. The maximum desirability was achieved as 0.98 (98%) for the factors, printing speed 100mm/min, infill density 60mm and layer thickness 0.3mm. The strength of the ABS specimen was predicted to be 23.83MPa. The observed strength value was 23.66MPa. The maximum desirability was obtained as 1 (100%) for the factors, printing speed 100mm/min, infill density 60mm and layer thickness 0.2mm. The strength of the carbon fiber PLA specimen was predicted to be 26.23MPa, and the obtained value was 26.49MPa.Research limitations/implicationsThe research shows the useful process parameters and their suitable working conditions to print the tensile specimens of the ABS and carbon fiber PLA thermoplastics by using the fused deposition modeling technique. The process was optimized to identify the most influential factor, and the desired optimum condition was achieved at which the maximum tensile strength was reported. The produced prediction expression can be used to predict the tensile strength of ABS and carbon fiber PLA filaments.Practical implicationsThe results obtained from the experimental investigation are useful to get an insight into the FDM process and working limits to print the parts by using the ABS and carbon fiber PLA material for various industrial and structural applications.Social implicationsThe results will be useful in choosing the suitable thermoplastic filament for the various prototyping and structural applications. The products that require freedom in design and are difficult to produce by most of the conventional techniques can be produced at low cost and in less time by the fused deposition modeling technique.Originality/valueThe process optimization shows the practical exposures to state an optimum working condition to print the ABS and carbon fiber PLA tensile specimens by using the FDM technique. The carbon fiber PLA shows better strength than ABS thermoplastic material.

Tensile Strength and Flexural Strength Testing of Acrylonitrile Butadiene Styrene (ABS) Materials for Biomimetic Robotic Applications

2014 ◽  
Vol 20 ◽  
pp. 11-21 ◽  
Author(s):  
Tran Linh Khuong ◽  
Zhao Gang ◽  
Muhammad Farid ◽  
Rao Yu ◽  
Zhuang Zhi Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Butadiene Styrene

Biomimetic robots borrow their structure, senses and behavior from animals, such as humans or insects, and plants. Biomimetic design is design ofa machine, a robot or a system in engineeringdomain thatmimics operational and/orbehavioral model of a biological system in nature. 3D printing technology has another name as rapid prototyping technology. Currently it is being developed fastly and widely and is applied in many fields like the jewelry, footwear, industrial design, architecture, engineering and construction, automotive, aerospace, dental and medical industry, education, geographic information system, civil engineering, guns. 3D printing technology is able to manufacture complicated, sophisticated details that the traditional processing method cannot manufacture. Therefore, 3D printing technology can be seen as an effective tool in biomimetic, which can accurately simulate most of the biological structure. Fused Deposition Modeling (FDM) is a technology of the typical rapid prototyping. The main content of the article is the focusing on tensile strength test of the ABS-Acrylonitrile Butadiene Styrene material after using Fused Deposition Modeling (FDM) technology, concretization after it’s printed by UP2! 3D printer. The article focuses on two basic features which are Tensile Strength and Determination of flexural properties.

scholarly journals Influence of Process Parameters on Tensile Strength of Additive Manufactured PLA Parts using Taguchi Method

2019 ◽  
Vol 8 (3) ◽  
pp. 7635-7639
Keyword(s):  
Tensile Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Optimal Parameter ◽  
Fused Filament Fabrication ◽  
Influence Of Process Parameters ◽  
Layer Height ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Nozzle Temperature

Influence of layer thickness nozzle temperature and angle on tensile strength of PLA fabricated with FDM (FFF) was experimentally investigated. Polylactic Acid (PLA) is a semi-crystalline and bio-friendly thermoplastic polymer has identified as important material in different applications due to its mechanical characteristics. Fused Deposition Modeling (FDM) is a one of the proved technology in Fused Filament Fabrication (FFF) technique in additive manufacturing process. In present investigation different specimens were fabricated using FDM technique with different layer height and different layer angles for finding influence of these manufacturing parameters on tensile strength of the specimen. Specimens were fabricated and tested as per ASTM D638 standard. It is clearly observed that tensile strength is more for +450 /-450 layer angle than the +00 /-0 0 layer angle for a given layer height(h=0.10 mm, h=0.15mm and h=0.20mm).The TAGUCHI analysis is carried with nozzle temperature, layer thickness and angle finding optimal values. It has been observed that, the optimal parameter is angle, which is equal to 30 0 .the ANOVA variation of angle layer with tensile strength has been observed that 18.10-31.90.

scholarly journals Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts

2016 ◽  
Vol 36 (3) ◽  
pp. 110 ◽  
Author(s):  
Kenny Álvarez ◽  
Rodrigo F. Lagos ◽  
Miguel Aizpun
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fused Deposition Modeling ◽  
Tensile Force ◽  
Impact Resistance ◽  
Acrylonitrile Butadiene Styrene ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Time

3D printing is a manufacturing process that is usually used for modeling and prototyping. One of the most popular printing techniques is fused deposition modeling (FDM), which is based on adding melted material layer by layer. Although FDM has several advantages with respect to other manufacturing materials, there are several problems that have to be faced. When setting the printing options, several parameters have to be taken into account, such as temperature, speed, infill percentage, etc. Selecting these parameters is often a great challenge for the user, and is generally solved by experience without considering the influence of variations in the parameters on the mechanical properties of the printed parts.This article analyzes the influence of the infill percentage on the mechanical properties of ABS (Acrylonitrile Butadiene Styrene) printed parts. In order to characterize this influence, test specimens for tensile strength and Charpy tests were printed with a Makerbot Replicator 2X printer, in which the infill percentage was varied but the rest of the printing parameters were kept constant. Three different results were analyzed for these tests: tensile strength, impact resistance, and effective printing time. Results showed that the maximum tensile force (1438N) and tensile stress (34,57MPa) were obtained by using 100% infill. The maximum impact resistance, 1,55J, was also obtained with 100% infill. In terms of effective printing time, results showed that printing with an infill range between 50% and 98% is not recommended, since the effective printing time is higher than with a 100% infill and the tensile strength and impact resistance are smaller. In addition, in comparing the results of our analysis with results from other authors, it can be concluded that the printer type and plastic roll significantly influence the mechanical properties of ABS parts.

The Influence of an Infill Density, Percent on the Flexural Strength of the 3D

2020 ◽  
Vol 870 ◽  
pp. 73-80
Author(s):  
Nuha Hadi Jasim Al Hasan
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Bending Test ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Deposition Modeling

3D printing innovation, as a quick prototyping, utilize plastic or metal as the crude material to print the genuine parts layer by layer. In this way, it is likewise called added substance producing procedure. Contrasted and conventional assembling innovation, 3D printing innovation has evident points of interest in assembling items with complex shapes and structures. Fused deposition modeling (FDM) is one of the most broadly utilized 3D printing advances. Fibers of thermoplastic materials, for example, polylactic acid is for the most part utilized as crude materials. The present examination will concentrate on the effect of the infill density, percent on the flexural strength of polylactic acid. Bending test was performed on different infill density, percent of specimens. According to ASTM D638.14 standards, samples for testing are made in different infill density, percent (20, 30, 40, 50 and 60 %) by using a polylactic acid in 3D machine printing and their tensile tested and the parameters include different fill density, layer high of 0.1 mm , 0.2mm and 0.3 have an effect on the mechanical characterized while the time of printing the sample would be increased with increasing of fill density%. The tensile strength of polylactic acid samples was found at different fill density and a layer thickness. According to test measuring results that the tensile strength, maximum 47.1,47.4, and 48 MPa at 30%,40%,and 50% fill density respectively and 0.1mm height layer and the tensile strength minimum at 60% and 70 % fill density and 0.1 mm height layer thickness. The higher strength results as higher layer thickness 0.3 mm as compared with 0.1 and 0.2 at 30%fill density.

Experimental Determination of the Tensile Strength of Fused Deposition Modeling Parts

2014 ◽  
Author(s):  
K. Savvakis ◽  
M. Petousis ◽  
A. Vairis ◽  
N. Vidakis ◽  
A. T. Bikmeyev
Keyword(s):  
Tensile Strength ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Test Machine ◽  
Average Deviation ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Lower Tensile Strength ◽  
Butadiene Styrene

Acrylonitrile–butadiene–styrene (ABS) is a popular engineering thermoplastic and it is the most common material used in fused deposition modeling (FDM) technology. This technology is nowadays used for the production of prototypes and functional parts as well. It is therefore critical to know the mechanical properties of these parts, which, is as expected different from their nominal values. In this work the tensile strength of parts build with the FDM process is measured. ABS and ABS plus parts were built with different building parameters and were tested according to the ASTM D638-02a standard on a Schenk Trebel Co. tensile test machine. It was found that the building direction does not significantly influence the tensile strength of the parts, although the parts were anisotropic, as expected. Parts build with larger layer thickness showed lower tensile strength. The average deviation between nominal and experimental tensile strength was about 15% for the ABS and about 42% for the ABS plus material. The ABS plus showed on average 9% higher strength than ABS.

Sign in / Sign up

Export Citation Format

Share Document