Sb2S3/SnSe thin film solar cells by thermal evaporation

2014 ◽  
Vol 1670 ◽  
Author(s):  
José Escorcia-García ◽  
Enue Barrios-Salgado ◽  
M.T.S. Nair ◽  
P.K. Nair
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Solar Cell ◽  
Thermal Evaporation ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Glass Substrates ◽  
Cell Structures

ABSTRACTWe report a stable CdS/Sb2S3/SnSe heterojunction thin film solar cell deposited on SnO2:F (FTO) – coated glass substrates. Thermal evaporation at 10-5 Torr with substrate temperature of 400 °C was used to deposit Sb2S3 and SnSe thin films of 450 nm and 160 nm, respectively. Thin film Sb2S3 has an optical band gap (Eg) of 1.48 eV and photoconductivity (σp) of 4x10-7 Ω-1 cm-1 and thin film SnSe has an Eg of 1.28 eV and σp of 2 Ω-1 cm-1. The chemically deposited CdS thin film heated at 400 °C shows an Eg of 2.34 eV and σp of 0.1 Ω-1 cm-1. Stabilized solar cell structures with these thin films, FTO/CdS/Sb2S3/SnSe/C-Ag, showed open circuit voltage (Voc) of 0.60 V, short circuit current density (Jsc) of 5.51 mA/cm2 and power conversion efficiency (η) of 0.96% with a fill factor FF of 0.29. In the absence of the SnSe layer, Jsc decreases to 4.77 mA/cm2.

All-Chemically Deposited Solar Cells with Antimony Sulfide-Selenide/Lead Sulfide Thin Film Absorbers

2007 ◽  
Vol 1012 ◽  
Author(s):  
Sarah Messina ◽  
M.T.S. Nair ◽  
P. K. Nair
Keyword(s):  
Thin Film ◽  
Solar Cell ◽  
Short Circuit ◽  
Chemical Deposition ◽  
Short Circuit Current ◽  
Transparent Conductive Oxide ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Cell Structures ◽  
Graded Band Gap

AbstractSolar cell structures with Sb2SxSe3-x and PbS as absorber layers were fabricated by chemical deposition on commercial transparent conductive oxide coated glass. The solid solution here was prepared by heating at 250°C a Sb2S3 thin film in contact with a chemically deposited Se-thin film. It has a graded band gap of 1-1.8 eV. A PbS thin film deposited on this layer basically fulfils the role of a p+ layer; its role as an absorber is yet to be studied. Open circuit voltage of 560 mV and short circuit current density ¡Ö 1mA/cm2under 1-3 kW/m2 tungsten halogen radiation are characteristics of these cells. Optimization of the film thicknesses and heating may offer prospects for these materials toward alternate thin film solar cell technology.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Optimized Thin-Film Organic Solar Cell with Enhanced Efficiency

2021 ◽  
Vol 13 (23) ◽  
pp. 13087
Author(s):  
Waqas Farooq ◽  
Muhammad Ali Musarat ◽  
Javed Iqbal ◽  
Syed Asfandyar Ali Kazmi ◽  
Adnan Daud Khan ◽  
...  
Keyword(s):  
Thin Film ◽  
Solar Cell ◽  
Organic Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Bragg Reflector ◽  
Performance Parameters ◽  
Distributed Bragg Reflector

Modification of a cell’s architecture can enhance the performance parameters. This paper reports on the numerical modeling of a thin-film organic solar cell (OSC) featuring distributed Bragg reflector (DBR) pairs. The utilization of DBR pairs via the proposed method was found to be beneficial in terms of increasing the performance parameters. The extracted results showed that using DBR pairs helps capture the reflected light back into the active region by improving the photovoltaic parameters as compared to the structure without DBR pairs. Moreover, implementing three DBR pairs resulted in the best enhancement gain of 1.076% in power conversion efficiency. The measured results under a global AM of 1.5G were as follows: open circuit voltage (Voc) = 0.839 V; short circuit current density (Jsc) = 10.98 mA/cm2; fill factor (FF) = 78.39%; efficiency (η) = 11.02%. In addition, a thermal stability analysis of the proposed design was performed and we observed that high temperature resulted in a decrease in η from 11.02 to 10.70%. Our demonstrated design may provide a pathway for the practical application of OSCs.

Preparation of the Three Main Layers of CdS/CdTe Thin Film Solar Cells Using a Single Vacuum System

2011 ◽  
Vol 378-379 ◽  
pp. 601-605 ◽  
Author(s):  
Saleh N. Alamri ◽  
M. S. Benghanem ◽  
A. A. Joraid
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Silica ◽  
Vacuum System ◽  
Cdte Thin Film

This study investigates the preparation of the three main layers of a CdS/CdTe thin film solar cell using a single vacuum system. A Close Space Sublimation System was constructed to deposit CdS, CdTe and CdCl2 solar cell layers. Two hot plates were used to heat the source and the substrate. Three fused silica melting dishes were used as containers for the sources. The properties of the deposited CdS and CdTe films were determined via Atomic force microscopy, scanning electron microscopy, X-ray diffraction and optical transmission spectroscopy. An J-V characterization of the fabricated CdS/CdTe solar cells was performed under solar radiation. The short-circuit current density, Jsc, the open-circuit voltage, Voc, fill factor, FF and conversion efficiency, η, were measured and yielded values of 27 mA/cm2, 0.619 V, 58% and 9.8%, respectively.

Revisiting CdS-PbS Solar Cell Structure

2007 ◽  
Vol 1012 ◽  
Author(s):  
Harumi Moreno Garcia ◽  
O. Gómez-Daza ◽  
J. Campos ◽  
M. T. S. Nair ◽  
P. K. Nair
Keyword(s):  
Solar Cell ◽  
Cell Structure ◽  
Short Circuit ◽  
Chemical Deposition ◽  
Distinct Type ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Cell Structures ◽  
Type V

AbstractCdS and PbS are well known semiconductor materials. Starting in 1969 and into 1970's CdS-PbS cells were reported with open circuit voltage (Voc) up to 450 mV and short circuit current density (Jsc) < 1 mA/cm2. However, further reports are scarce. These two materials are also the most investigated by chemical deposition technique. In this work we revisit this type of photovoltaic junctions and present the photovoltaic behavior of distinct type of cell structures prepared by chemical deposition: glass/CdS/PbS/Ag, SnO2:F/CdS/PbS/Ag, and SnO2:F/CdS/(Bi2S3 or/and CdSe)/PbS/Ag. Depending on the cell type, Voc of > 500 mV or Jsc of > 3 mA/cm2 could be obtained under illumination of 1-3 kW/m2. This work opens up possibilities for developing simple solar cell structures by sequential chemical deposition of semiconductors.

Preparation of Narrow-gap a-Si:H Solar Cells by VHF-PECVD Technique

2010 ◽  
Vol 1245 ◽  
Author(s):  
Do Yun Kim ◽  
Ihsanul Afdi Yunaz ◽  
Shunsuke Kasashima ◽  
Shinsuke Miyajima ◽  
Makoto Konagai
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Solar Cell ◽  
Spectral Response ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Hydrogen Flow ◽  
Long Wavelength

AbstractOptical, electrical and structural properties of silicon films depending on hydrogen flow rate (RH), substrate temperature (TS), and deposition pressure (PD) were investigated. By decreasing RH and increasing TS and PD, the optical band gap (Eopt) of silicon thin films drastically declined from 1.8 to 1.63 eV without a big deterioration in electrical properties. We employed all the investigated Si thin films for p-i-n structured solar cells as absorbers with i-layer thickness of 300 nm. From the measurement of solar cell performances, it was clearly observed that spectral response in long wavelength was enhanced as Eopt of absorber layers decreased. Using the solar cell whose Eopt of i-layer was 1.65 eV, the highest QE at long wavelength with the short circuit current density (Jsc) of 16.34 mA/cm2 was achieved, and open circuit voltage (Voc), fill factor (FF), and conversion efficiency (η) were 0.66 V, 0.57, and 6.13%, respectively.

Chemically and Electrochemically Deposited Thin Films of Tin Sulfide for Photovoltaic Structures

2009 ◽  
Vol 1165 ◽  
Author(s):  
Nini Rose Mathews
Keyword(s):  
Thin Films ◽  
Short Circuit ◽  
Chemical Deposition ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Tin Sulfide ◽  
Orthorhombic Crystal ◽  
Orthorhombic Crystal Structure ◽  
Glass Substrates

AbstractThin films of tin sulfide (SnS) were deposited on TCO-coated glass substrates by pulse electrodeposition. Cyclic voltammetry showed that SnS deposition occurs in the -0.8 V to −1 V range. The films deposited using the potential pulses of -0.95V (Von) and +0.1V (Voff) are of orthorhombic crystal structure with lattice parameters and grain size similar to those of the thin films of orthorhombic structure obtained by chemical deposition. The optical band gap of the films was 1.3 eV. In CdS/SnS heterojunctions an open circuit voltage110 mV, short circuit current density 0.72 mA/cm2 and fill factor of 0.32 are reported here.

scholarly journals Using Cu–Zn–Sn–O Precursor to Optimize CZTSSe Thin Films Fabricated by Se Doping With CZTS Thin Films

2021 ◽  
Vol 9 ◽  
Author(s):  
Qian Li ◽  
Jinpeng Hu ◽  
Yaru Cui ◽  
Juan Wang ◽  
Yu Hao ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Short Circuit ◽  
Surface Characteristics ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Se Doping ◽  
Zinc Tin Oxide ◽  
Czts Thin Films

The copper–zinc–tin oxide (CZTO) precursor was synthesized to avoid sudden volume expansion from CZTO precursor to Cu2ZnSnS4 (CZTS) thin films and smooth CZTSSe thin-film surfaces without pinholes. The CZTO precursor was prepared by coprecipitation and ball milling to form nanoink of CZTO. Based on the CZTO precursor, the CZTS thin film was fabricated and then selenized to make pinhole-free and flat Cu2ZnSn(S,Se)4(CZTSSe) thin films. The results show that the CZTO precursor greatly contributed to elevating the homologous surface characteristics and crystallinity of CZTSSe thin films by controlling selenium temperature, selenium time, and selenium source temperature. Finally, the conversion efficiency of the CZTSSe thin-film solar cell fabricated from the CZTO precursor was 4.11%, with an open-circuit voltage (Voc) of 623 mV, a short circuit current density (Jsc) of 16.02 mA cm−2, and a fill factor (FF) of 41.2%.

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

2020 ◽  
Vol 92 (2) ◽  
pp. 20901
Author(s):  
Abdul Kuddus ◽  
Md. Ferdous Rahman ◽  
Jaker Hossain ◽  
Abu Bakar Md. Ismail
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Heterojunction Solar Cell ◽  
Back Surface ◽  
Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

scholarly journals Simulation of a perovskite sandwich solar cell with the p-CZTS / p-CH3NH3PbCI3 / p-CZTS absorber layers

2021 ◽  
Vol 877 (1) ◽  
pp. 012001
Author(s):  
Marwah S Mahmood ◽  
N K Hassan
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Current Density ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Current Voltage ◽  
Cell Capacitance

Abstract Perovskite solar cells attract the attention because of their unique properties in photovoltaic cells. Numerical simulation to the structure of Perovskite on p-CZTS/p-CH3NH3PbCI3/p-CZTS absorber layers is performed by using a program solar cell capacitance simulator (SCAPS-1D), with changing absorber layer thickness. The effect of thickness p-CZTS/p-CH3NH3PbCI3/p-CZTS, layers at (3.2μm, 1.8 μm, 1.1 μm) respectively are studied. The obtained results are short circuit current density (Jsc ), open circuit voltage (V oc), fill factor (F. F) and power conversion efficiency (PCE) equal to (28 mA/cm2, 0.83 v, 60.58 % and 14.25 %) respectively at 1.1 μm thickness. Our findings revealed that the dependence of current - voltage characteristics on the thickness of the absorbing layers, an increase in the amount of short circuit current density with an increase in the thickness of the absorption layers and thus led to an increase in the conversion efficiency and improvement of the cell by increasing the thickness of the absorption layers.

Sign in / Sign up

Export Citation Format

Share Document