Difference between Wafer Temperature and Thermocouple Reading during rapid Thermal Processing

1998 ◽  
Vol 525 ◽  
Author(s):  
T. Borca-Tasciuc ◽  
D. A. Achimov ◽  
G. Chen
Keyword(s):  
Temperature Measurement ◽  
Thermophysical Properties ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Simple Analytical Model ◽  
Calibration Standard ◽  
Wafer Temperature ◽  
Thermocouple Reading ◽  
The Difference ◽  
Thermocouple Temperature

ABSTRACTThermocouples are often used as a calibration standard for rapid thermal processing. Although it has been recognized that the thermocouple temperature can be different from the wafer temperature, the magnitude of the temperature difference is difficult to quantify. In this work, we present a simple analytical model to demonstrate the difference between the thermocouple temperature and the true wafer temperature. The results show that a large difference can exist between the thermocouple and the wafer temperature. This is because the optical and thermophysical properties of the thermocouple and the glue material are different from those of the wafer. The model results show that temperature measurement becomes more accurate if fine diameter thermocouple wires with very low emissivity are used.

Diffusion of Zn into Gaas 0.6 P0.4:Te From Zn-Doped Oxide Films By Rapid Thermal Processing

1987 ◽  
Vol 92 ◽  
Author(s):  
A. Usami ◽  
Y. Tokuda ◽  
H. Shiraki ◽  
H. Ueda ◽  
T. Wada ◽  
...  
Keyword(s):  
Diffusion Coefficient ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Oxide Films ◽  
Zn Diffusion ◽  
Enhanced Diffusion ◽  
Conventional Furnace ◽  
Zn Concentration ◽  
The Difference ◽  
Doped Oxide

ABSTRACTRapid thermal processing using halogen lamps was applied to the diffusion of Zn into GaAs0.6 P0.4:Te from Zn-doped oxide films. The Zn diffusion coefficient of the rapid thermal diffused (RTD) samples at 800°C for 6 s was about two orders of magnitude higher than that of the conventional furnace diffused samples at 800°C for 60 min. The enhanced diffusion of Zn by RTD may be ascribed to the stress field due to the difference in the thermal expansion coefficient between the doped oxide films and GaAs0.6P0.4 materials, and due to the temperature gradient in GaAs0.6P0 4 materials. The Zn diffusion coefficient at Zn concentration of 1.0 × l018 cm−3 was 3.6 × 10−11, 3.1 × 10−11 and 5.0 × 10−12 cm2 /s for the RTD samples at 950°C for 6 s from Zn-, (Zn,Ga)- and (Zn,P)-doped oxide films, respectively. This suggests that Zn diffusibility was controlled by the P in the doped oxide films.

scholarly journals Simulation of silicon wafers heating during rapid thermal processing using “UBTO 1801” unit

Doklady BGUIR ◽  
2020 ◽  
Vol 18 (7) ◽  
pp. 79-86
Author(s):  
J. A. Solovjov ◽  
V. A. Pilipenko ◽  
V. P. Yakovlev
Keyword(s):  
Mathematical Model ◽  
Silicon Wafer ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Light Flux ◽  
Silicon Wafers ◽  
Wafer Surface ◽  
Constant Density ◽  
Wafer Temperature

The present work is devoted to determination of the dependence of the heating temperature of the silicon wafer on the lamps power and the heating time during rapid thermal processing using “UBTO 1801” unit by irradiating the wafer backside with an incoherent flow of constant density light. As a result, a mathematical model of silicon wafer temperature variation was developed on the basis of the equation of nonstationary thermal conductivity and known temperature dependencies of the thermophysical properties of silicon and the emissivity of aluminum and silver applied to the planar surface of the silicon wafer. For experimental determination of the numerical parameters of the mathematical model, silicon wafers were heated with light single pulse of constant power to the temperature of one of three phase transitions such as aluminum-silicon eutectic formation, aluminum melting and silver melting. The time of phase transition formation on the wafer surface during rapid thermal processing was fixed by pyrometric method. In accordance with the developed mathematical model, we determined the conversion coefficient of the lamps electric power to the light flux power density with the numerical value of 5.16∙10-3 cm-2 . Increasing the lamps power from 690 to 2740 W leads to an increase in the silicon wafer temperature during rapid thermal processing from 550°to 930°K, respectively. With that, the wafer temperature prediction error in compliance with developed mathematical model makes less than 2.3 %. The work results can be used when developing new procedures of rapid thermal processing for silicon wafers.

Temperature Measurement Issues in Rapid Thermal Processing

1997 ◽  
Vol 470 ◽  
Author(s):  
D. P. DeWitt ◽  
F. Y. Sorrell ◽  
J. K. Elliott
Keyword(s):  
Temperature Measurement ◽  
Thermal Processing ◽  
Radiation Effects ◽  
Temperature Scale ◽  
Rapid Thermal Processing ◽  
Radiative Properties ◽  
Spectral Radiance ◽  
Roughness Effects ◽  
Thermal Radiative Properties ◽  
Stray Radiation

ABSTRACTReliable radiometrie temperature measurement has been a major challenge in making rapid thermal processing (RTP) more widely accepted. In order to meet road map requirements involving temperature uncertainty, uniformity and control, new techniques must be demonstrated and/or existing measurement methods must be substantially improved. Critical aspects of radiometrie methods for temperature measurement are centered about the topics: radiative and optical properties of the wafers including layered systems, surface roughness effects, and reflected irradiation from lamp banks and chamber walls. The systematic method for inferring temperature is rooted in the measurement equation which relates the radiometer output to the exitent spectral radiance from the target which reaches the detector and prescribes the roles that emissivity variability and stray radiation have on the result. An overview is provided on the knowledge base for optical and thermal radiative properties. Methods for reducing emissivity and stray radiation effects are summarized. Calibration procedures necessary to assure that the in-chamber or local temperature scale is traceable to the International Temperature Scale (ITS-90) are discussed. The issues which can impact improved temperature measurement practice are summarized.

In-Situ Temperature Control for Rtp Via Thermal Expansion Measurement

1993 ◽  
Vol 303 ◽  
Author(s):  
Bruce Peuse ◽  
Allan Rosekrans
Keyword(s):  
Thermal Expansion ◽  
Temperature Control ◽  
Measurement Technique ◽  
Preliminary Data ◽  
Thermal Processing ◽  
Rapid Thermal Processing ◽  
Processing System ◽  
Wafer Temperature ◽  
Thermal Expansion Measurement

ABSTRACTA new method of temperature control for rapid thermal processing of silicon wafers is presented whereby in-situ wafer temperature is determined by measurement of wafer thermal expansion via an optical micrometer mechanism. The expansion measurement technique and its implementation into a rapid thermal processing system for temperature control are described. Preliminary data show the wafer to wafer temperature repeatability to be 1% (3-σ) using this technique.

Sign in / Sign up

Export Citation Format

Share Document