Low-Resistance Electrical Contacts to p-Type GaN by Using InxGa1-xN Cap Layers

2001 ◽  
Vol 693 ◽  
Author(s):  
Th. Gessmann ◽  
Y.-L. Li ◽  
J. W. Graff ◽  
E. F. Schubert ◽  
J. K. Sheu
Keyword(s):  
Contact Resistance ◽  
Electric Fields ◽  
Ohmic Contacts ◽  
Electrical Contacts ◽  
Specific Contact Resistance ◽  
Low Resistance ◽  
Transmission Line Method ◽  
Specific Contact ◽  
P Type ◽  
20 Nm

AbstractA novel type of low-resistance ohmic contacts is demonstrated utilizing polarization-induced electric fields in thin p-type InGaN layers on p-type GaN. An increase of the hole tunneling probability through the barrier and a concomitant significant decrease of the specific contact resistance can be attributed to a reduction of the tunneling barrier width in the InGaN capping layers due to the polarization-induced electric fields. The specific contact resistance of Ni (10 nm) / Au (30 nm) contacts deposited on the InGaN capping layers was determined by the transmission line method. Specific contact resistances of 1.2 × 10-2 Ω cm2 and 6 × 10-3 & cm2 were obtained for capping layer thicknesses of 20 nm and 2 nm, respectively.

Al/Ni And Al/Ti Ohmic Contact To P-type SiC Diffused Layer

2000 ◽  
Vol 640 ◽  
Author(s):  
Xaiobin Wang ◽  
Stanislav Soloviev ◽  
Ying Gao ◽  
G. Straty ◽  
Tangali Sudarshan ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Metal Contacts ◽  
Transfer Length ◽  
Type Layer ◽  
Transmission Line Method ◽  
Specific Contact ◽  
Background Doping ◽  
P Type

ABSTRACTOhmic contacts to p-type SiC were fabricated by depositing Al/Ni and Al/Ti followed by high temperature annealing. A p-type layer was fabricated by Al or B diffusion from vapor phase into both p-type and n-type substrates. The thickness of the diffused layer was about 0.1–0.2 μm with surface carrier concentration of about 1.0×1019cm−3. Metal contacts to a p-type substrate with a background doping concentration of 1.2×1018cm−3, without a diffusion layer, were also formed. The values of specific contact resistance obtained by Circular Transmission Line Method (CTLM) and Transfer Length Method (TLM) for the n-type substrate, and by Cox & Strack method for p-type substrate, respectively, varied from 1.3×10−4Ωcm2 to 8.8×10−3 Ωcm2. The results indicate that the specific contact resistance could be significantly reduced by creating a highly doped diffused surface layer.

Ti/Al/Si Ohmic Contacts for both n-Type and p-Type 4H-SiC

2014 ◽  
Vol 778-780 ◽  
pp. 669-672 ◽  
Author(s):  
Hideto Tamaso ◽  
Shunsuke Yamada ◽  
Hiroyuki Kitabayashi ◽  
Taku Horii
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Contact Process ◽  
Oxide Semiconductor ◽  
Specific Contact Resistance ◽  
Transfer Length ◽  
Specific Contact ◽  
Effect Transistor ◽  
P Type ◽  
20 Nm

An ohmic contact process by using tri-layer materials for a source contact of a silicon carbide (SiC) metal oxide semiconductor field effect transistor (MOSFET) is proposed. The authors validate its extremely low contact resistance for both n-type and p-type SiC by a simple process. The characteristics of Ti/Al/Si ohmic contacts were measured by using the transfer length method (TLM). We examined the dependence of the contact resistance on the thickness of each layer of Ti/Al/Si. Then, it is found that Ti/Al/Si contacts with an appropriate thickness show excellent ohmic properties for both n-type and p-type SiC. N-type specific contact resistance (ρn) of 3.7 × 10-6 Ω cm2 and p-type specific contact resistance (ρp) of 1.7 × 10-4 Ω cm2 are obtained with Ti (20 nm) /Al (30 nm) /Si (30 nm).

Pt/Ti Low Resistance Non-Alloyed Ohmic Contacts to InP-Based Photonic Devices

1989 ◽  
Vol 146 ◽  
Author(s):  
A. Katz ◽  
S. N. G. Chu ◽  
P. M. Thomas ◽  
W. C. Dautremont-Smith
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Metal Layer ◽  
Photonic Devices ◽  
Electrical Performance ◽  
Specific Contact Resistance ◽  
Low Resistance ◽  
Specific Contact ◽  
20 Nm ◽  
Resistance Value

ABSTRACTPt/ri low resistance non-alloyed ohmic contacts to p-InP-based contact layers in photonic devices, which were formed by rapid thermal processing (RTP), were studied. E-gun evaporated Pt/Ti metallization deposited onto 1.5· 1019 cm−3 Zn doped In0.53Ga0.47 As yielded the best electrical performance. These contacts were ohmic as deposited with a specific contact resistance value of 3.0 · 10−4 Ωcm2. RTP at higher temperatures led to decrease of the specific contact resistance to 3.4 · 10−8 Ωcm2 (0.08Ωmm) as a result of heating at 450°C for 30 sec. This heat treatment caused only a limited interfacial reaction (about 20 nm thick) between the Ti and the InGaAs, resulted in a thermally stable contact and induced tensile stress of 5.6 · 109 dyne · cm−2 at the metal layer but without degrading the adhesion. Heating at temperatures higher than 500°C resulted in an extensive interaction and degradation of the contact.

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Ohmic Contacts to p-Type InGaAs/InP with a Graded Bandgap Heterobarrier

1993 ◽  
Vol 318 ◽  
Author(s):  
Patrick W. Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Rutherford Backscattering Spectrometry ◽  
Specific Contact Resistance ◽  
Superlattice Structure ◽  
Specific Contact ◽  
P Type ◽  
Metal Layers ◽  
Anneal Temperature ◽  
Graded Bandgap

ABSTRACTOhmic contacts to p-type InP with an In0.47Ga0.53As buffer layer and an interposed superlattice of 50 Å In0.47Ga0.53As/ 50 Å InP have been investigated. Initial studies of contacts to In0.47Ga0.53As/ InP without the superlattice structure have shown that Pd/Zn/Pd/Au metallization produced a lower specific contact resistance (pc = 1.1 × 10−4 Ω cm2) than Pd/Ge/Au, and over a wider range of anneal temperature than Au/Zn/Au. The incorporation of the superlattice in the p-In0.47Ga0.53As/ InP structure resulted in Pd/Zn/Pd/Au contacts with pc of 3.2 × 10−5 Ω cm2 as-deposited and 7.5 × 10−6 Ω.cm2 after a 500 °C anneal. The presence of Pd/Zn in the metallization was shown as important in reducing pc. Significant intermixing of the metal layers and In0.47Ga0.53As occured at ≥ 350 °C, as revealed by Rutherford backscattering spectrometry.

Ni-Al-Ti Ohmic Contacts with Preserved Form Factor and Few 10- 4 Ωcm2 Specific Resistance on 0.1-1 Ωcm p-Type 4H-SiC

2018 ◽  
Vol 924 ◽  
pp. 385-388 ◽  
Author(s):  
Roberta Nipoti ◽  
Maurizio Puzzanghera ◽  
Maria Concetta Canino ◽  
Giovanna Sozzi ◽  
Paolo Fedeli
Keyword(s):  
Form Factor ◽  
Contact Resistance ◽  
Contact Area ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Resistance ◽  
Thickness Ratio ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type

This study shows that a thin Ni film on Al/Ti/4H-SiC metal pads allows to preserve the pad form factor during a 1000 °C/2 min treatment, provided that the Al and Ti film thicknesses are sufficiently thin. Moreover, by reducing the Al to Ti thickness ratio, droplet formation in the contact area is avoided and a mirror-like appearance is obtained. This optimal contact morphology corresponds to a specific contact resistance of few 10-4Ωcm2at room temperature on p-type 4H-SiC with resistivity in the range 0.1 – 1 Ωcm.

TiW/TiWN/Pt Ohmic Contacts to n-Type 3C-SiC

2006 ◽  
Vol 911 ◽  
Author(s):  
Kirk Hofeling ◽  
Loren Rieth ◽  
Florian Solzbacher
Keyword(s):  
Contact Resistance ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Test Duration ◽  
Capping Layer ◽  
Interface Reactions ◽  
Transmission Line Method ◽  
Specific Contact

AbstractTiW(40 nm)/TiWN(80 nm)/Pt(500nm) was investigated as a new high-temperature compatible contact stack to 3C-SiC for harsh environment applications. Performance of TiW/TiWN/Pt contacts deposited on unintentionally doped (8.85×1018 cm-3) 3C-SiC grown by LPCVD to a thickness of ~1μm on (100) Si are reported. The linear transmission line method was used to determine specific contact resistance (ρc) at room temperature and for long-term tests at 300 °C. As deposited contacts were Ohmic with a ρc range of 1×10-4 to 1×10-3 cm2. These contacts were annealed for five minutes in forming gas (8% H2 92% Ar), at temperatures from 450 to 950 °C and all retained Ohmic character. Annealing samples at 450, 550 and 950 °C decreased ρc while anneling between 650 and 850 °C generally increased ρc.Auger Electron Spectroscopy (AES) analysis was performed on a sample annealed at 750 °C. The as-received surface was composed of Si and O; after a brief sputter etch a characteristic Pt peak became visible and the O peak decreased substantially. Depth profiles detected Si throughout the Pt capping layer but not in the TiW layers. We suspect that Si diffuses from the SiC substrate into the Pt capping layer and surface Si also reacts with O2 to from an oxide. These reactions, in combination with incomplete SiC/TiW interface reactions, are suspected to cause the increase of ρc for samples annealed between 650 and 850 °C. Annealing at 950 °C gave the lowest contact resistance of 2.3×10-5. Long-term testing at 300 °C for 190 hours, in atmosphere, was performed on contacts annealed at 450 °C. When heated, the contacts initial ρc of 2.1×10-4 cm2 increased to ~4×10-3 cm2 which remained stable for the test duration. After long-term testing the sample ρc measured at room temperature decreased to 9.8×10-5 cm2.

scholarly journals Comparison of Electrical Properties of Ohmic Contact Realized on p-Type 4H-SiC

2008 ◽  
Vol 600-603 ◽  
pp. 639-642
Author(s):  
Duy Minh Nguyen ◽  
Christophe Raynaud ◽  
Mihai Lazar ◽  
Heu Vang ◽  
Dominique Planson
Keyword(s):  
Surface Roughness ◽  
Electrical Properties ◽  
Contact Resistance ◽  
Carrier Mobility ◽  
Ohmic Contacts ◽  
Series Resistance ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type ◽  
Post Implantation

N+ 4H-SiC commercial substrates with n-type epilayers have been used to realize bipolar diodes and TLM structures. The p-type emitter of diodes was realized by Al implantations followed by a post-implantation annealing with or without a graphite capping layer. Ohmic contacts were formed by depositing Ti/Ni on the backside and Ni/Al on the topside of the wafer. It appears that capping the sample during the annealing reduces considerably the surface roughness and the specific contact resistance. Sheet resistance and specific contact resistance as low as 2kΩ/□ and respectively 1.75×10-4 Ωcm² at 300 K have been obtained. I-V measurements as a function of temperature have been performed from ~100 to ~500 K. The variations of the series resistance vs. temperature can be explained by the freeze-out of carriers and by the variation of carrier mobility.

Improved Low Resistance Contacts of Ni/Au and Pd/Au to P-Type GaN Using a Cryogenic Treatment

1999 ◽  
Vol 595 ◽  
Author(s):  
Mi-Ran Park ◽  
Wayne A. Anderson ◽  
Seong-Ju Park
Keyword(s):  
Contact Resistance ◽  
Ohmic Contact ◽  
Cryogenic Treatment ◽  
Microstructural Analysis ◽  
Chemical Vapor ◽  
Specific Contact Resistance ◽  
Mixed Gas ◽  
Low Resistance ◽  
Specific Contact ◽  
P Type

AbstractA low resistance Ohmic contact to p-type GaN is essential for reliable operation of electronic and optoelectronic devices. Such contacts have been made using Ni/Au and Pd / Au contacts to p-type Mg-doped GaN (1.41×1017 cm−3) grown by metalorganic chemical vapor deposition ( MOCVD ) on ( 0001 ) sapphire substrates. Thermal evaporation was used for the deposition of those metals followed by annealing at temperatures of 400 ∼ 700 °C in an oxygen and nitrogen mixed gas ambient, then subsequently cooled in liquid nitrogen which reduced the specific contact resistance from the range of 9.46∼2.80×10−2 ωcm2 to 9.84∼2.65×10−4 ωcm2 for Ni/Au and from the range of 8.35∼5.01×10−4 ωcm2 to 3.34∼1.80×10−4 ωcm2 for Pd/Au. The electrical characteristics for the contacts were examined by the current versus voltage curves and the specific contact resistance was determined by use of the circular transmission line method (c-TLM). The effects of the cryogenic process on improving Ohmic behavior (I-V linearity) and reducing the specific contact resistance will be discussed from a microstructural analysis which reveals the metallurgy of Ohmic contact formation.

scholarly journals Improved Low Resistance Contacts of Ni/Au and Pd/Au to p-Type GaN Using a Cryogenic Treatment

2000 ◽  
Vol 5 (S1) ◽  
pp. 901-907
Author(s):  
Mi-Ran Park ◽  
Wayne A. Anderson ◽  
Seong-Ju Park
Keyword(s):  
Contact Resistance ◽  
Ohmic Contact ◽  
Cryogenic Treatment ◽  
Microstructural Analysis ◽  
Chemical Vapor ◽  
Specific Contact Resistance ◽  
Mixed Gas ◽  
Low Resistance ◽  
Specific Contact ◽  
P Type

A low resistance Ohmic contact to p-type GaN is essential for reliable operation of electronic and optoelectronic devices. Such contacts have been made using Ni/Au and Pd / Au contacts to p-type Mg-doped GaN (1.41×1017 cm−3) grown by metalorganic chemical vapor deposition ( MOCVD ) on ( 0001 ) sapphire substrates. Thermal evaporation was used for the deposition of those metals followed by annealing at temperatures of 400 ∼ 700 °C in an oxygen and nitrogen mixed gas ambient, then subsequently cooled in liquid nitrogen which reduced the specific contact resistance from the range of 9.46∼2.80×10−2 Ωcm2 to 9.84∼2.65×10−4 Ωcm2 for Ni/Au and from the range of 8.35∼5.01×10−4 Ωcm2 to 3.34∼1.80×10−4 Ωcm2 for Pd/Au. The electrical characteristics for the contacts were examined by the current versus voltage curves and the specific contact resistance was determined by use of the circular transmission line method (c-TLM). The effects of the cryogenic process on improving Ohmic behavior (I-V linearity) and reducing the specific contact resistance will be discussed from a microstructural analysis which reveals the metallurgy of Ohmic contact formation.

Sign in / Sign up

Export Citation Format

Share Document