Physical and Electrical Characterization of Synthesized Millimeter Size Single Crystal Graphene, Using Controlled Bubbling Transfer

In this work, we have investigated the influence of the transfer process on the monocrystalline graphene in terms of quality, morphology and electrical properties by analyzing the data obtained from optical microscopy, scanning electron microscopy, Raman spectroscopy and electrical characterizations. The influence of Cu oxidation on graphene prior to the transfer is also discussed. Our results show that the controlled bubbling electrochemical delamination transfer is an easy and fast transfer technique suitable for transferring large single crystals graphene without degrading the graphene quality. Moreover, Raman spectroscopy investigation reveals that the Cu surface oxidation modifies the strain of the graphene film. We have observed that graphene laying on unoxidized Cu is subject to a biaxial strain in compression, while graphene on Cu oxide is subject to a biaxial strain in tension. However, after graphene was transferred to a host substrate, these strain effects were strongly reduced, leaving a homogeneous graphene on the substrate. The transferred single crystal graphene on silicon oxide substrate was used to fabricate transmission line method (TLM) devices. Electrical measurements show low contact resistance ~150 Ω·µm, which confirms the homogeneity and high quality of transferred graphene.

Thermal Boundary Resistance Extraction of GaN-on-Diamond Substrate from Transmission Line Method Pattern Using Micro-Raman Spectroscopy and Thermal Simulation

Heat dissipation properties are very important in AlGaN/GaN RF high electron mobility transistor (HEMT) devices operating at high frequency and high power. Therefore, in order to extract the thermal conductivity of the substrate and device, which are essential for the analysis of the heat dissipation characteristics, various methods of extraction were attempted. And this experiments were conducted in parallel with micro-raman measurement and thermal simulation. As a result, it was possible to extract the thermal conductivity of each GaN-on-diamond epi layer by matching the thermal simulation data and the shift of the micro-raman peak according to various operating states and temperatures of the transmission line method (TLM) pattern. In particular, we tried to extract the thermal boundary resistance (TBR) of the interface layer (SiNx) for adhesion between GaN and diamond, which greatly affects the thermal conductivity of the device, and successfully extracted the following thermal conductivity value of KTBR = 3.162·(T/300)−0.8 (W/mK) from GaN and diamond interface layer.

Formation and investigation of characteristics of thermoresistive structures based on vanadium oxide films

The processes of reactive magnetron sputtering of a V target in Ar/O2 gas mixture are investigated. It was found that when using a pulsed current for sputtering and a pressure in the chamber less than 0.06 Pa, the intensities of the emission lines of vanadium at 437.922 nm, argon at 750.386 nm, and oxygen at 777.417 nm with a change in the oxygen concentration in Ar/O2 gas mixtures (ГO2) have no hysteresis and unambiguously depend on the parameters of the sputtering process, which makes it possible to stabilize the process without using feedback systems. By monitoring the sputtering process by optical emission spectroscopy and depositing films on a rotating substrate of diameter 100 mm, vanadium oxide (VOx) films with nonuniformity thickness less than ±2.4 % and surface resistance less than ±2.5 % were obtained. Studies by transmission line method of the influence of the parameters of the reactive magnetron sputtering and subsequent annealing at O2 pressure of 0.04 Pa on the characteristics of thermoresistive structures based on VOx films showed that when the contacts are deposited without ion cleaning, the current-voltage characteristics (IV) and the dependence of the resistance on the length of resistors R(L) are nonlinear, which indicates the presence of a potential barrier in the contacts. Preliminary ion cleaning can significantly improve the linearity of the IV characteristic. The most linear IV characteristics were obtained for Ti contacts. However, the specific contact resistance of the VOx/Ti contact increases with an increase in the oxidation state of the VOx films and reaches ρc = 0.1 Ohm·m2 at the specific resistance of vanadium oxide ρ = 0.1 Ohm·m. The analysis of the dependences of the temperature coefficient of resistance (TCR) and ρ of VOx films on the annealing temperature showed that, upon annealing, ρ and TCR slightly decrease, i. e. there occurs a partial deoxidation of the films. However, unlike annealing at atmospheric pressure, there are no temperature regions at which a sharp decrease in the resistivity and TCR occurs.

A TLM Formulation Based on Fractional Derivatives for Dispersive Cole-Cole Media

An auxiliary differential equation (ADE) transmission line method (TLM) is proposed for broadband modeling of electromagnetic (EM) wave propagation in biological tissues with the Cole-Cole dispersion Model. The fractional derivative problem is surmounted by assuming a linear behavior of the polarization current when the time discretization is short enough. The polarization current density is approached using Lagrange extrapolation polynomial and the fractional derivation is obtained according to Riemann definition of a fractional α -order derivative. Reflection coefficients at an air/muscle and air/fat tissues interfaces simulated in a 1-D domain are found to be in good agreement with those obtained from the analytic model over a broad frequency range, demonstrating the validity of the proposed approach.

Analysis of the performance of grounding grids buried in heterogeneous soil under impulse current

The present paper is devoted to analyzing the transient behaviour of simple grounding grids subjected to impulse lightning current. The transmission line method (TLM) involving mutual coupling between conductors will be used. The transient behaviour of grounding grids buried in homogeneous and in heterogeneous soil is going to be evaluated into a complete time domain solution. Different simulations carried out altering, the influence of the grid dimensions, the kind of the ground and the current injection point on the grid voltage and impedance will be presented. Simulation results will be shown for two extreme cases: in the first case the current is in the center of the grid and in the second one it is injected in one corner of the two configurations of grids. The obtained results show that the grid 1x1 gives the lowest transient potential when the injection point is in lower resistivity side, and the grid 2x2 presents better behavior when the current is injected at center point. It is obvious that the suggested simulations are in a good agreement, with corresponding results of other researchers.

Couplinator: A simple computational tool for synthesis of multi-section coupled-line filter based on MPCM-TLM technique

A new simple computational tool is proposed for the synthesis of multi-section coupled-line filters based on combined modified planar circuit method (MPCM) and transmission line method (TLM) analysis, referred to as MPCM-TLM. Due to its fundamentally simple architecture, the presented tool offers significantly faster optimization of coupled-line filters – for exactly the same initial simulation set-up – than other costly commercially-available tools, giving equally reliable results. Validity and accuracy of the proposed tool have been verified through the design of 3rd, 5th, and 7th order coupled-line filters and comparative analysis between results obtained from the proposed approach and the high-frequency structure simulator. A remarkable 99% time reduction in the analysis is recorded in the case of 7th order filter using the proposed tool, for almost identical results to HFSS. Therefore, it can be confidently claimed that the proposed technique can be used as a reliable alternative to existing complex, costly, processor-intensive CAD tools.

Characterization of Joints between Carbon Fiber Composite Parts Using a Microstrip Transmission Line Method

The electromagnetic performance of aerial platforms, which are composed mostly of nonmetallic materials, is a subject of great interest at present time. The behavior of this type of composite structure against electromagnetic environmental effects (E3), such as lightning, is not well-studied as in the case of metalic structures. The purpose of this article is to characterize the joints present in aerial platforms constructed mainly of nonmetallic composite materials. The study of these joints is fundamental because electrical discontinuities or preferential routes can produce changes in the electromagnetic behavior of an aircraft. The proposed measurement system for the characterization of these joints is a microstrip line. The flexibility of the test setup allows for evaluation of different joints in carbon fiber composite (CFC) samples with a different number of plies. Additionally, approximated models of the behavior of the joints as well as the detection of possible defects in the joining process are reported.