Impact of physical and mechanical properties of materials being joined on the formation of stress-strain state in the joint in diffusion welding

2014 ◽  
Vol 0 (4) ◽  
Author(s):  
Viktor V. Kvasnytskyi ◽  
Maksym V. Matvienko
Keyword(s):  
Mechanical Properties ◽  
Strain State ◽  
Physical And Mechanical Properties ◽  
Diffusion Welding ◽  
Stress Strain ◽  
Stress Strain State ◽  
Mechanical Properties Of Materials ◽  
Properties Of Materials

scholarly journals About One of the Approaches for the Research of the Stress-Strain State of a Flange Connection with a Seal Made of an Alloy with Shape Memory

2022 ◽  
Author(s):  
A. Boikov
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Contact Zone ◽  
Axial Compression ◽  
Strain State ◽  
Physical And Mechanical Properties ◽  
Stress Strain ◽  
Flange Connection ◽  
Stress Strain State ◽  
Alternative Approach

Abstract. Design features of a flange connection with a seal made of an alloy with shape memory and the most commonly used methods of researching of the stress-strain state of such connections are estimated. Alternative approach for stress-strain state analysis is proposed, it is based on modeling of the contact zone of the sealing surfaces by means of an equivalent gap between the layers, the value of which changes during axial compression of the multilayer ring and goes into tension. Formulas for determining of contact stresses at the border of layers, which take into consideration the variable physical and mechanical properties of the materials of each layer are presented.

Analysis of the stress-strain state of copper M0B under different schemes of equal channel angular pressing and its effect on the structure and physical and mechanical properties

2019 ◽  
pp. 47-53
Author(s):  
L. F. Sennikova ◽  
G. K. Volkova ◽  
V. M. Tkachenko
Keyword(s):  
Equal Channel Angular Pressing ◽  
Strain State ◽  
Physical And Mechanical Properties ◽  
Strength Properties ◽  
Stress Strain ◽  
Loading Pattern ◽  
Stress Strain State ◽  
Angular Pressing ◽  
Fine Copper ◽  
Copper Structure

The results of studies of the stress-strain state of copper M0b after deformation under different schemes of equal channel angular pressing (ECAP) are presented. The level of macro and micro stresses in copper has been determined in various ECAP modes. It is shown that the strength properties, deformation porosity and parameters of the fine copper structure differ depending on the loading pattern.

Bending Process Simulation of a Flat Workpiece with Various Cross-Sectional Mechanical Properties with PAM-STAMP 2G

2016 ◽  
Vol 685 ◽  
pp. 133-136 ◽  
Author(s):  
Fedor Grechnikov ◽  
Yurii Gorshkov ◽  
Yaroslav Erisov
Keyword(s):  
Mechanical Properties ◽  
Heat Affected Zone ◽  
Process Simulation ◽  
Laser Cutting ◽  
Strain State ◽  
Stress Strain ◽  
Cross Sectional ◽  
Stress Strain State ◽  
Bending Process

We have simulated an aluminum workpiece tool bending process with and without consideration of the heat affected zone after laser cutting with PAM-STAMP 2G. To describe the heat affected zone we have used a customized software option for calculating welded materials and dissimilar ones. We have also provided an analysis of the stress-strain state with a different scale of mechanical properties of the material on its “edge” and in the center of the workpiece.

scholarly journals Application of a computational and experimental method of analysis the complexly stressed state of rubber membranes for effective solutions for their production

2021 ◽  
Vol 83 (2) ◽  
pp. 230-236
Author(s):  
D. V. Kudelin ◽  
T. N. Nesiolovskaya
Keyword(s):  
Stressed State ◽  
Experimental Method ◽  
Strain State ◽  
Physical And Mechanical Properties ◽  
Standard Test ◽  
Spherical Indenter ◽  
Bag Filter ◽  
Stress Strain ◽  
Rubber Membrane ◽  
Stress Strain State

The competitiveness of rubber membranes determined by their durability, quality, reliability, including the time required to create. During operation, the membranes undergo complex deformations, as a result of which a large number of potential destruction zones of a different nature arise, which can lead to the failure of the product. The standard test methods used in the development of formulations for membranes involve testing the material under uniaxial tension conditions in most cases and do not take into account the actual loading conditions of the product during operation, which significantly increases the development time of new formulations for membranes. The paper presents and applies in practice a computational and experimental method of analysis the complexly stressed state of rubber membranes, including carrying out simple laboratory tests in a heterogeneous complexly stressed state, which is realized during the operation of rubber membranes, and analyzing the stress-strain state by the finite element method. An inhomogeneous complexly stressed state was realized by forcing the rubber membrane with a spherical indenter. The application of a computational-experimental method for analyzing the complexly stressed state of rubber membranes is considered on the example of a rubber corrugated membrane of an automatic valve of a bag filter purge system. An assessment of the physical and mechanical properties of rubbers in a heterogeneous complexly stressed state was carried out, as well as an analysis of the stress-strain state of the membrane when it was loaded with a spherical indenter, which made it possible to identify the most dangerous zones of the section. The complex use of this method made it possible to improve the resource of this corrugated membrane by thirty five percent in comparison with the standard, while reducing the creation time.

scholarly journals Compressed Flexible Steel Reinforced Concrete Elements Investigation

2018 ◽  
Vol 7 (3.2) ◽  
pp. 436
Author(s):  
Leonid Storozhenko ◽  
Pavlo Semko ◽  
Olena Yefimenko
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Strain State ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Experimental Sample ◽  
Sample Design ◽  
Stress Strain ◽  
Steel Reinforced Concrete ◽  
Concrete Elements

Stress-strain state and compressed flexible steel-reinforced concrete elements resistance capacity are investigated in the work. The experiment program is complied and steel reinforced concrete elements calculations methods are analyzed. Experimental sample design drawings are shown. Raw materials physical and mechanical properties are determined. Steel reinforced-concrete elements experimental and research studies have been carried out. Coboundary dependences N-M for steel reinforced concrete elements construction method is proposed. Resistance capacity diagrams for steel reinforced concrete elements are constructed depending on the element height and the applied eccentricity.  

scholarly journals Analysis of the possibility of using polylactide in production of building materials

2020 ◽  
Vol 217 ◽  
pp. 01012
Author(s):  
Maria Kaddo
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Building Materials ◽  
Physical And Mechanical Properties ◽  
Comparative Data ◽  
Mechanical Properties Of Materials ◽  
Fundamental Possibility ◽  
Properties Of Materials

The article analyzes the features of the production, use and utilization of biodegradable biopolymers. The results of studies are presented, the purpose of which is to assess the combination of properties of polylactide for use in construction. The fundamental possibility of using a thermoplastic biopolymer based on lactide (lactic acid) for the production of building materials is considered. Comparative data on the results of studies of the physical and mechanical properties of materials based on polylactide are presented.

Sign in / Sign up

Export Citation Format

Share Document