INVESTIGATION OF THE EFFECT OF ELASTIC DEFORMATIONS OF THE WING MODEL OF A WIDE-BODY COMMERCIAL TRANSPORT AIRCRAFT ON ITS AERODYNAMIC CHARACTERISTICS

2018 ◽  
Vol 49 (7) ◽  
pp. 771-780
Author(s):  
Valery Viktorovich Vozhdaev ◽  
Leonid Leonidovich Teperin
Keyword(s):  
Aerodynamic Characteristics ◽  
Elastic Deformations ◽  
Transport Aircraft ◽  
Wing Model

scholarly journals Features of flow around transport aircraft model with running propellers by modelled engine failure in wind tunnel

2021 ◽  
Vol 2103 (1) ◽  
pp. 012206
Author(s):  
V I Chernousov ◽  
A A Krutov ◽  
E A Pigusov
Keyword(s):  
Wind Tunnel ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Light Transport ◽  
Transport Aircraft ◽  
Engine Failure ◽  
The One ◽  
Low Speed Wind Tunnel ◽  
Control Surfaces ◽  
Landing Mode

Abstract This paper presents the experiment results of modelling the one engine failure at the landing mode on a model of a light transport airplane in the T-102 TsAGI low speed wind tunnel. The effect of starboard and port engines failure on the aerodynamic characteristics and stability of the model is researched. The model maximum lift coefficient is reduced about ≈8% and there are the same moments in roll and yaw for starboard and port engines failure case. It was found that the failure of any engine has little impact on the efficiency of control surfaces. Approaches of compensation of forces and moments arising in the engine failure case were investigated.

scholarly journals Aerodynamic Analysis of a Flapping Wing Aircraft for Short Landing

2020 ◽  
Vol 10 (10) ◽  
pp. 3404
Author(s):  
Bing Ji ◽  
Zenggang Zhu ◽  
Shijun Guo ◽  
Si Chen ◽  
Qiaolin Zhu ◽  
...  
Keyword(s):  
Aerodynamic Characteristics ◽  
Flapping Wing ◽  
Aerodynamic Analysis ◽  
Drag Forces ◽  
Wing Model ◽  
Aerodynamic Model ◽  
Computational Fluid Dynamics Cfd ◽  
The Difference ◽  
Cfd Method ◽  
Lift And Drag

An investigation into the aerodynamic characteristics has been presented for a bio-inspired flapping wing aircraft. Firstly, a mechanism has been developed to transform the usual rotation powered by a motor to a combined flapping and pitching motion of the flapping wing. Secondly, an experimental model of the flapping wing aircraft has been built and tested to measure the motion and aerodynamic forces produced by the flapping wing. Thirdly, aerodynamic analysis is carried out based on the measured motion of the flapping wing model using an unsteady aerodynamic model (UAM) and validated by a computational fluid dynamics (CFD) method. The difference of the average lift force between the UAM and CFD method is 1.3%, and the difference between the UAM and experimental results is 18%. In addition, a parametric study is carried out by employing the UAM method to analyze the effect of variations of the pitching angle on the aerodynamic lift and drag forces. According to the study, the pitching amplitude for maximum lift is in the range of 60°~70° as the flight velocity decreases from 5 m/s to 1 m/s during landing.

Surface Modifications for Improved Maneuverability and Performance of an Aircraft

2011 ◽  
Author(s):  
Deepanshu Srivastav ◽  
K. N. Ponnani
Keyword(s):  
Surface Modifications ◽  
Boundary Layer Separation ◽  
Aerodynamic Characteristics ◽  
Aircraft Wing ◽  
Pressure Drag ◽  
Wing Model ◽  
Study Results ◽  
Stall Angle ◽  
And Performance ◽  
Lift And Drag

The work describes a comparative study of aerodynamic characteristics of an aircraft wing model with and without surface modifications to it. The surface modifications that are considered here are outward dimples on the wing model. In the present study, results of computational fluid dynamics (CFD) analysis are presented showing variance in lift and drag of modified wing models at different angle of attacks. Dimples on the surface aircraft wing model doesn’t affect much the pressure drag since it’s already aerodynamic in shape but it can affect the angle of stall. This project verifies if the dimples that reduce a golf ball’s drag, can also increase an airplane’s critical angle of stall. Dimples delay the boundary layer separation by creating more turbulence over the surface. The airfoil profile considered here is NACA-0018 with uniform cross-section throughout the length of airfoil. Subsonic flows are considered for the study. The CAD model is prepared in CatiaV5 R18 and simulations are carried out in Comsol 3.4 and Comsol 4.0. The overall aim of the study is improved maneuverability and performance of an aircraft. The results justify the increase in the overall lift and reduction in drag of the aircraft, also change of stall angle with different surface modifications on the wing model is observed.

scholarly journals Investigation of Aerodynamic Characteristics of a Wing Model With RGV Winglet

2020 ◽  
Author(s):  
Sivaraj Gopal Krishnan ◽  
Mohammad Hafifi Ishak ◽  
Mohammad Azwan Nasirudin ◽  
Farzad Ismail
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Vortex Formation ◽  
Aerodynamic Characteristics ◽  
Contour Plot ◽  
Tip Vortices ◽  
Wing Model ◽  
Plot Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Drag Ratio

This work describes the aerodynamic characteristics of an aircraft wing model with a Rüppell’s griffon vulture (RGV)-type winglet. A computational fluid dynamics (CFD) study using ANSYS 15.0 was conducted to study the effect of the RGV winglet on a rectangular wing. The NACA 65(3)-218 wing consists of 660 mm span and 121 mm chord length where the aspect ratio is 5.45. Eight different winglet configurations have been studied. Furthermore, the study is extended to study effect of cant angle and different angles of attack (AOA) to the winglet. A comparative study is done on aerodynamic features such as lift coefficient (CL), drag coefficient (CD), lift/drag ratio (CL/CD) and tip vortices to get the best RGV winglet design. The RGV winglet achieved highest CL compared to other types of winglets configuration. Based on contour plot analysis, the RGV winglet shows lower vortex formation compared to without winglet. The results show about 15 to 30% reduction in drag coefficient and 5 to 25% increase in lift coefficient by using an RGV winglet.

scholarly journals Analysis of the propellers-airframe interaction of the light transport aircraft

2021 ◽  
Vol 24 (5) ◽  
pp. 76-88
Author(s):  
Yu. S. Mikhailov
Keyword(s):  
Wind Tunnel ◽  
Experimental Studies ◽  
Aerodynamic Characteristics ◽  
High Energy ◽  
Light Transport ◽  
Transport Aircraft ◽  
High Energy Level ◽  
Combined Use ◽  
Wind Tunnel Balance ◽  
Propeller Blades

In the design of multi-engine aircraft, one of the important issues is the interaction between the propellers and airframe configuration components, especially in take-off and go-around procedure modes. Modern propeller-driven aircraft concepts in the pulling configuration are characterized by a high disk loading and an increased number of propeller blades used to increase cruising speed and reduce excessive noise. The first problem arising due to high disk loading is the direct impact of forces by operating propellers (thrust, normal force) on fixed-wing stability, especially at angles of attack different from a zero value. The second one involves a high-energy level of the propeller slipstream, having a significant indirect impact on the aircraft’s aerodynamics, stability and controllability. This impact is primarily associated with the interaction of propellers slipstream with other aircraft’s configuration elements. The complexity of taking into account the slipstream-wing interaction and other airframe components stipulated the application of experimental methods to study the problems of propellers – airframe interaction while designing propeller-driven aircraft configurations. This article presents an analysis of the experimental studies results of the operating propellers- airframe interaction for a light twin-engine transport aircraft. The aerodynamic aircraft’s configuration is executed using the conventional pattern of a high-wing and the carrier-on deck type empennage. The high-lift wing device is a fixed-vane doubleslotted flap. The wind-tunnel tests of the model in the cruising, takeoff and landing configurations were carried out in TsAGI lowspeed wind-tunnel T-102. Measurement of forces and moments, acting on the model, was performed by means of an external sixcomponent wind-tunnel balance. Measurement of forces and moments, acting on the propeller, was conducted using strain gauge weighers installed inside the engine nacelles of power plant simulators. The simultaneous combined use of external and internal balances allowed researchers to determine the direct and indirect contribution of operating propellers to the model longitudinal aerodynamic characteristics under variation of loading factor B ranging from 0 to 2.

Static Aeroelasticity Analysis of High Aspect Ratio Wing and the Jig-Shape Design Based on Multi-Block Structural Grid

2013 ◽  
Vol 302 ◽  
pp. 377-383 ◽  
Author(s):  
Yan Liu ◽  
Jun Qiang Bai ◽  
Jun Hua
Keyword(s):  
Aspect Ratio ◽  
Design Process ◽  
High Aspect Ratio ◽  
Design Method ◽  
Aerodynamic Characteristics ◽  
Shape Design ◽  
Transport Aircraft ◽  
Mesh Motion ◽  
Static Aeroelasticity ◽  
Motion Method

The influence of structural elastic deformation on the aerodynamic characterisitcs of large transport aircraft has been researched. A method of static aeroelasticity based on multi-block structural grid of high aspect ratio wing has been established, and then a design method of jig-shape is developed. The technology of RBF interpolation is used to exchange the data of CFD/CSD. Based on RBF&Delaunay technology, a mesh motion method is developed to make the design process less time-consuming, which can be applied to large deformation of multi-block structural grid. The static aeroelastic deformation of a wing-body of large transport aircraft is analyzed. Then the wing-body's jig-shape is designed. Compared the aerodynamic characteristics between design cruise shape and target cruise shape, it shows that the aerodynamic characteristics of design cruise shape is almost equal to target cruise shape and the design process of jig-shape is feasible.

Sign in / Sign up

Export Citation Format

Share Document