scholarly journals Investigation of Aerodynamic Characteristics of a Wing Model With RGV Winglet

2020 ◽  
Author(s):  
Sivaraj Gopal Krishnan ◽  
Mohammad Hafifi Ishak ◽  
Mohammad Azwan Nasirudin ◽  
Farzad Ismail
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Vortex Formation ◽  
Aerodynamic Characteristics ◽  
Contour Plot ◽  
Tip Vortices ◽  
Wing Model ◽  
Plot Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Drag Ratio

This work describes the aerodynamic characteristics of an aircraft wing model with a Rüppell’s griffon vulture (RGV)-type winglet. A computational fluid dynamics (CFD) study using ANSYS 15.0 was conducted to study the effect of the RGV winglet on a rectangular wing. The NACA 65(3)-218 wing consists of 660 mm span and 121 mm chord length where the aspect ratio is 5.45. Eight different winglet configurations have been studied. Furthermore, the study is extended to study effect of cant angle and different angles of attack (AOA) to the winglet. A comparative study is done on aerodynamic features such as lift coefficient (CL), drag coefficient (CD), lift/drag ratio (CL/CD) and tip vortices to get the best RGV winglet design. The RGV winglet achieved highest CL compared to other types of winglets configuration. Based on contour plot analysis, the RGV winglet shows lower vortex formation compared to without winglet. The results show about 15 to 30% reduction in drag coefficient and 5 to 25% increase in lift coefficient by using an RGV winglet.

Numerical Simulation on Aerodynamic of the Wing in Ground Effect

2012 ◽  
Vol 546-547 ◽  
pp. 200-205
Author(s):  
Rong Wu ◽  
Feng Liang
Keyword(s):  
Numerical Simulation ◽  
Drag Coefficient ◽  
Finite Volume Method ◽  
Lift Coefficient ◽  
Ground Effect ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performances ◽  
Volume Method ◽  
Drag Ratio

Aerodynamic characteristics of the wing NACA5312 in ground effect are investigated with the numerical simulation method. The N-S equations and the k-ε turbulence model are solved by the finite volume method in CFD software. This paper computes the flying states under different clearances, steam velocities and angles of attack. Compared with results under the unbounded flow, it studies the relations between the aerodynamic performances and the angles of attack, the steam velocity, and the relative heights. The aerodynamic performances include the lift coefficient, drag coefficient, and lift-drag ratio.

scholarly journals Lift and Drag Coefficient Map of NACA4415 Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012066
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Optimal Angle ◽  
Fluent Software ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The NACA4415 airfoil was numerically simulated with the help of the Fluent software to analyze its aerodynamic characteristics. Results are acquired as follows: The calculation accuracy of Fluent software is much higher than that of XFOIL software; the calculation result of SST k-ω(sstkw) turbulence model is closest to the experimental value; within a certain range, the larger the Reynolds number is, the larger the lift coefficient and lift-to-drag ratio of the airfoil will be, and the smaller the drag coefficient will be; when the angle of attack is less than the optimal angle of attack, the Reynolds number has less influence on the lift-to-drag coefficient and the lift-to-drag ratio; as the Reynolds number increases, the optimal angle of attack increases slightly, and the applicable angle of attack range for high lift-to-drag ratios becomes smaller.

scholarly journals Effects of Pitching Motion Elements on Aerodynamic Characteristics of Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012078
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Initial Angle ◽  
Pitching Motion ◽  
The Difference ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The aerodynamic characteristics of NACA4412 airfoil with different pitching motion elements were compared and analyzed based on CFD in this research. The results are acquired as follows: the difference between the lift and drag coefficients of the airfoil during pitch up and pitch down motions becomes larger with the increase of the pitching amplitude or initial angle of attack; as the pitching amplitude increases, the lift coefficient grows slightly greater and the drag coefficient grows much greater; as the initial angle of attack increases, the lift coefficient grows much greater and the drag coefficient grows slightly; the smaller the attenuation frequency is, the larger the lift-to-drag ratio of the airfoil will be.

scholarly journals Experimental Determination of the Impact of Floats on the Aerodynamic Characteristics of an OSA Model in Symmetric Flow

2021 ◽  
Vol 12 (1) ◽  
pp. 41-58
Author(s):  
Michał FRANT ◽  
Stanisław WRZESIEŃ ◽  
Maciej MAJCHER
Keyword(s):  
Drag Coefficient ◽  
Aerodynamic Drag ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Symmetric Flow ◽  
Aerodynamic Drag Coefficient ◽  
The Impact ◽  
Drag Ratio ◽  
Lift To Drag Ratio

This paper presents the results of experimental determination of the impact of floats on the aerodynamic characteristics of an OSA model in symmetric flow. The studies have been performed in the low-speed wind tunnel at the Military University of Technology (MUT, Warsaw, Poland). The aircraft model was examined at the dynamic pressure q = 500 Pa in the following angle of attack range = -2828. The investigations have been performed for an aircraft model under plain configuration with floats and without floats. The influence of elevator and flap inclination on the aerodynamic characteristics of the model has also been analysed. The obtained values of aerodynamic drag coefficient, lift coefficient, pitching moment coefficient and lift-to-drag ratio have been presented in the form of tables and graphs. The studies performed demonstrated that the use of floats causes the increase of aerodynamic drag coefficient CD, maximum lift coefficient CLmax as well as critical angle of attack cr. The decrease of lift-to-drag ratio has also been observed. Its value in the case of the model with floats was up to 20% lower than in the model without floats. The studies also showed that the model equipped with floats had a lower longitudinal static stability margin than the model without floats.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

Aerodynamic characteristics of breathing blunt nose configuration at hypersonic speeds

2016 ◽  
Vol 231 (5) ◽  
pp. 840-858 ◽  
Author(s):  
Yasumasa Watanabe ◽  
Kojiro Suzuki ◽  
Ethirajan Rathakrishnan
Keyword(s):  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
The Body ◽  
Positive Pressure ◽  
Stagnation Region ◽  
Total Drag ◽  
Hypersonic Speeds ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Blunt Nose

Breathing blunt nose technique is one of the promising methods for reducing the drag of blunt-nosed body at hypersonic speeds. The air, traversed by the bow shock positioned ahead of the nose, at the stagnation region is allowed to enter through a hole at the blunt-nose and ejected at the rear part (base region) of the body. This manipulation reduces the positive pressure over the stagnation regions of the nose and increases the pressure at the base, resulting in reduced suction at the base. The simultaneous manifestation of reducing the compression at the nose and suction at the base regions results in reduction of the total drag. The drag reduction caused by the breathing blunt nose technique has been measured in a Mach 7 tunnel. Also, the drag and flow field around the blunt-nosed body, with and without breathing hole, has been computed. The aerodynamic characteristics of the breathing blunt nose model obtained experimentally are compared with the CFD results. It is found that the breathing results in 5% reduction in drag. The lift coefficient also comes down for the model with breathing nose. But the lift-to-drag ratio is found to be the same for both the cases; the blunt-nosed body with and without nose-hole.

scholarly journals Aerodynamic Analysis of a Flapping Wing Aircraft for Short Landing

2020 ◽  
Vol 10 (10) ◽  
pp. 3404
Author(s):  
Bing Ji ◽  
Zenggang Zhu ◽  
Shijun Guo ◽  
Si Chen ◽  
Qiaolin Zhu ◽  
...  
Keyword(s):  
Aerodynamic Characteristics ◽  
Flapping Wing ◽  
Aerodynamic Analysis ◽  
Drag Forces ◽  
Wing Model ◽  
Aerodynamic Model ◽  
Computational Fluid Dynamics Cfd ◽  
The Difference ◽  
Cfd Method ◽  
Lift And Drag

An investigation into the aerodynamic characteristics has been presented for a bio-inspired flapping wing aircraft. Firstly, a mechanism has been developed to transform the usual rotation powered by a motor to a combined flapping and pitching motion of the flapping wing. Secondly, an experimental model of the flapping wing aircraft has been built and tested to measure the motion and aerodynamic forces produced by the flapping wing. Thirdly, aerodynamic analysis is carried out based on the measured motion of the flapping wing model using an unsteady aerodynamic model (UAM) and validated by a computational fluid dynamics (CFD) method. The difference of the average lift force between the UAM and CFD method is 1.3%, and the difference between the UAM and experimental results is 18%. In addition, a parametric study is carried out by employing the UAM method to analyze the effect of variations of the pitching angle on the aerodynamic lift and drag forces. According to the study, the pitching amplitude for maximum lift is in the range of 60°~70° as the flight velocity decreases from 5 m/s to 1 m/s during landing.

Based on Imitation Seagull Airfoil UVA Wing Numerical Simulation

2012 ◽  
Vol 271-272 ◽  
pp. 791-796
Author(s):  
Xin Hua ◽  
Wei Shao ◽  
Chun Hua Zhang ◽  
Zhi Qiang Zhang
Keyword(s):  
Numerical Simulation ◽  
High Performance ◽  
Lift Coefficient ◽  
Wind Tunnel Test ◽  
Aerodynamic Characteristics ◽  
Wing Scale ◽  
Fluent Software ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Straight Wing

Wing aircraft is one of the major components to generate lift, in today's energy shortage, design the high lift-to-drag ratio wing is the goal pursued by, The author in the exploration of bionic airfoil aerodynamic characteristics on the basis of, which will be applied to straight wing design so as to improve the aerodynamic performance of aircraft.Our research mainly includes two aspects: first, the use of imitation seagull airfoil and NACA4412 airfoil are designed into the straight wing. The use of FLUENT software in Re=300000condition carries on the numerical simulation results show that the ratio of gull wing airfoil than NACA4412 lift coefficient increased by 13%, while the lift to drag ratio,is improved by 46.83%. Then, using the similarity principle, the wing scale, was tested in a wind tunnel test, the results obtained with the simulation are consistent. Airfoil design for the design of high performance wing opened a new way.

Numerical Study of Winglet Cant Angle Effect on Wing Performance at Low Reynolds Number

2013 ◽  
Vol 393 ◽  
pp. 366-371
Author(s):  
C.F. Mat Taib ◽  
Abdul Aziz Jaafar ◽  
Salmiah Kasolang
Keyword(s):  
Reynolds Number ◽  
Numerical Analysis ◽  
Numerical Study ◽  
Low Reynolds Number ◽  
Lift Coefficient ◽  
Wing Model ◽  
Low Reynolds ◽  
Wing Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The study on the effect of winglet shape in wing design has been a focus of many researchers. Nevertheless, the effect of cant angle on the wing performances at low Reynolds number has not been fully explored. This paper describes the effect of a single semi-circular shaped winglet attached with a rectangular wing model to lower the drag without increasing the span of the wing. Aerodynamic characteristics for the rectangular wing (NACA 65-3-218) with and without semi-circular winglets have been studied using STAR CCM+ 4.0. This numerical analysis is based on Finite Volume Approach. Simulations were carried out on the rectangular wing model with and without winglet at aspect ratio of 2.73 and Reynolds number of 0.16 x 10 6 for various angles of attack. From the numerical analysis, wing performance characteristics in terms of lift coefficient CL, drag coefficient CD, and lift-to-drag ratio, CL/CD were obtained. It was found that the addition of a semi-circular winglet has resulted in a larger lift curve slope and higher Lift-to-Drag ratio in comparison with the case of a wing without winglet. Further investigation has revealed that a wing with semi-circular winglet with cant angle of 45 degree has produced the best Lift-to-Drag ratio, CL/CD.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document