ANALYSIS OF MECHANICAL SYSTEM VENTILATION PERFORMANCE IN AN ATRIUM BY CONSOLIDATED MODEL OF FIRE AND SMOKE TRANSPORT SIMULATION

2015 ◽  
Vol 33 (3) ◽  
pp. 121-126 ◽  
Author(s):  
Awni Alkhazaleh ◽  
Hamzeh Duwairi
Keyword(s):  
Mechanical System ◽  
Transport Simulation ◽  
Smoke Transport ◽  
Ventilation Performance

Study of the dynamics of ТПА 350 automatic mill working stand elements

2020 ◽  
Vol 76 (8) ◽  
pp. 830-840
Author(s):  
S. R. Rakhmanov ◽  
V. V. Povorotnii
Keyword(s):  
Mechanical System ◽  
Dynamic Model ◽  
Maximum Amplitude ◽  
Calculation Scheme ◽  
Dynamic Loads ◽  
Forced Oscillations ◽  
Mass Model ◽  
Automatic Mill ◽  
Hollow Billet ◽  
Oscillation Movement

To form a necessary geometry of a hollow billet to be rolled at a pipe rolling line, stable dynamics of the base equipment of the automatic mill working stand has a practical meaning. Among the forces, acting on its parts and elements, significant by value short-time dynamic loads are the least studied phenomena. These dynamic loads arise during transient interaction of the hollow billet, rollers, mandrel and other mill parts at the forced grip of the hollow billet. Basing of the calculation scheme and dynamic model of the mechanical system of the ТПА 350 automatic mill working stand was accomplished. A mathematical model of dynamics of the system “hollow billet (pipe) – working stand” within accepted calculation scheme and dynamic model of the mechanical system elaborated. Influence of technological load of the rolled hollow billet variation in time was accounted, as well as variation of the mechanical system mass, and rigidity of the ТПА 350 automatic mill working stand. Differential equations of oscillation movement for four-mass model of forked sub-systems of the automatic mill working stand were made up, results of their digital calculation quoted. Dynamic displacement of the stand elements in the inter-roller gap obtained, which enabled to estimate the results of amplitude and frequency characteristics of the branches of the mill rollers setting. It was defined by calculation, that the maximum amplitude of the forced oscillations of elements of the ТПА 350 automatic mill working stand within the inter-roller gap does not exceed 2 mm. It is much higher than the accepted value of adjusting parameters of the deformation center of the ТПА 350 automatic mill. A scheme of comprehensive modernization of the rollers setting in the ТПА 350 automatic mill working stand was proposed. It was shown, that increase of rigidity of rollers setting in the ТПА 350 automatic mill working stand enables to stabilize the amplitude of forced oscillations of the working stand elements within the inter-rollers gap and considerably decrease the induced nonuniform hollow billet wall thickness and increase quality of the rolled pipes at ТПА 350.

Analysis of a 2DOF Nonlinear Mechanical System Using the Normal Form Method

2019 ◽  
Author(s):  
David Julian Gonzalez Maldonado ◽  
Peter Hagedorn ◽  
Thiago Ritto ◽  
Rubens Sampaio ◽  
Artem Karev
Keyword(s):  
Normal Form ◽  
Mechanical System ◽  
Nonlinear Mechanical ◽  
Nonlinear Mechanical System ◽  
Normal Form Method

Numerical and Experimental Modeling of Indoor Air Quality Inside a Conditioned Space with Mechanical Ventilation and DX-Air Conditioner

2020 ◽  
Vol 38 (9A) ◽  
pp. 1257-1275
Author(s):  
Wisam M. Mareed ◽  
Hasanen M. Hussen
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Ventilation System ◽  
Thermal Conditions ◽  
Airflow Rate ◽  
Air Conditioner ◽  
Breathing Zone ◽  
Lecture Room ◽  
Ventilation Performance

 Elevated CO2 rates in a building affect the health of the occupant. This paper deals with an experimental and numerical analysis conducted in a full-scale test room located in the Department of Mechanical Engineering at the University of Technology. The experiments and CFD were conducted for analyzing ventilation performance. It is a study on the effect of the discharge airflow rate of the ceiling type air-conditioner on ventilation performance in the lecture room with the mixing ventilation. Most obtained findings show that database and questionnaires analyzed prefer heights between 0.2 m to 1.2 m in the middle of an occupied zone and breathing zone height of between 0.75 m to 1.8 given in the literature surveyed. It is noticed the mismatch of internal conditions with thermal comfort, and indoor air quality recommended by [ASHRAE Standard 62, ANSI / ASHRAE Standard 55-2010]. CFD simulations have been carried to provide insights on the indoor air quality and comfort conditions throughout the classroom. Particle concentrations, thermal conditions, and modified ventilation system solutions are reported.

Mechanical System for End‐Trimming Soybean Plots 1

Crop Science ◽  
1978 ◽  
Vol 18 (2) ◽  
pp. 351-352
Author(s):  
J. C. Freed ◽  
J. B. Bahrenfus ◽  
T. J. Bandstra ◽  
W. R. Fehr ◽  
R. C. Clark
Keyword(s):  
Mechanical System

The Analogical Turn (1884–1887)

2018 ◽  
Author(s):  
Olivier Darrigol
Keyword(s):  
Boltzmann Equation ◽  
Statistical Mechanics ◽  
Mechanical System ◽  
Thermal Equilibrium ◽  
Special Kind ◽  
Second Law Of Thermodynamics ◽  
Second Law ◽  
Equipartition Theorem ◽  
Royal Road ◽  
H Theorem

This chapter recounts how Boltzmann reacted to Hermann Helmholtz’s analogy between thermodynamic systems and a special kind of mechanical system (the “monocyclic systems”) by grouping all attempts to relate thermodynamics to mechanics, including the kinetic-molecular analogy, into a family of partial analogies all derivable from what we would now call a microcanonical ensemble. At that time, Boltzmann regarded ensemble-based statistical mechanics as the royal road to the laws of thermal equilibrium (as we now do). In the same period, he returned to the Boltzmann equation and the H theorem in reply to Peter Guthrie Tait’s attack on the equipartition theorem. He also made a non-technical survey of the second law of thermodynamics seen as a law of probability increase.

Sign in / Sign up

Export Citation Format

Share Document