scholarly journals Nanoparticle number from biodiesel blends combustion in a common rail fuel injection system diesel engine equipped with exhaust gas recirculation

2009 ◽  
Vol 138 (3) ◽  
pp. 28-36
Author(s):  
Sathaporn CHUEPENG ◽  
Hongming XU ◽  
Athanasios TSOLAKIS ◽  
Mirosław WYSZYŃSKI ◽  
Jonathan HARLAND
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Particle Number ◽  
Fuel Injection ◽  
Exhaust Gas Recirculation ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System ◽  
Exhaust Gas ◽  
Gas Recirculation

The paper presents characterisations of nanoparticle number in exhaust gases from biodiesel blends (B30, 30% of RME by volume with ultra low sulphur diesel fuel, ULSD) combustion in a V6 diesel engine equipped with a common rail fuel injection system. The engine was operated on three steady-state test points extracted from the New European Driving Cycle without engine hardware or the engine management system (EMS) modification. A fast differential mobility spectrometer was used to determine particle number size distribution based on electrical mobility equivalent diameter. The distribution was dependent on the engine operating condition and the rate of exhaust gas recirculation (EGR). The particle size in the nucleation mode from B30 combustion with and without EGR is smaller than that of ULSD while giving higher number concentration for all engine operating conditions tested. However, in the accumulation mode with and without EGR, the smaller sizes and the lower total numbers from B30 combustion were observed. For both fuels, EGR shows insignificant changes to the primary particle size but noticeable increase in particle size and number in the accumulation mode. In overall, compared to the ULSD case, the B30 combustion reduced particle size and lowered total particle number in exhaust gas emitted from the engine with EGR.

Biodiesel Combustion and Emissions in Engines Using Modern Common-Rail Fuel Injection Systems

2008 ◽  
Author(s):  
Prashanth K. Karra ◽  
Matthias K. Veltman ◽  
Song-Charng Kong
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Exhaust Gas Recirculation ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Fuel Injection System ◽  
Nox Emissions ◽  
Exhaust Gas ◽  
Gas Recirculation

This study performed experimental testing of a multi-cylinder diesel engine using different blends of biodiesel and diesel fuel. The engine used an electronically-controlled common-rail fuel injection system to achieve a high injection pressure. The operating parameters that were investigated included the injection pressure, injection timing, and exhaust gas recirculation rate. Results showed that biodiesel generally reduced soot emissions and increased NOx emissions. The increase in NOx emissions was not due to the injection timing shift when biodiesel was used because the present fuel injection system was able to give the same fuel injection timing. At high exhaust gas recirculation rates, emissions using regular diesel and 20% biodiesel blends are very similar while 100% biodiesel produces relatively different emission levels. Therefore, the increase in NOx emissions may not be a concern when 20% biodiesel blends are used with high exhaust gas recirculation rates in order to achieve low temperature combustion conditions.

Effects of Exhaust Gas Recirculation on Particulate Morphology from a Diesel Engine

2013 ◽  
Vol 664 ◽  
pp. 926-930
Author(s):  
Wei Zhang ◽  
Xiao Dong Wang ◽  
Rui Sun ◽  
Jian Wei Sun ◽  
Wei Han
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Primary Particle ◽  
Morphological Characteristics ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Injection System ◽  
Exhaust Gas ◽  
Aggregate Particle ◽  
Gas Recirculation

The effects of EGR operating mode on particulate morphology were investigated for a 5.79-liter diesel engine which was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. Morphological characteristics, such as primary particle size, number concentration and aggregate particle size were investigated by a transmission electron microscope (TEM) analysis and a electrical low pressure impactor (ELPI) under engine operating conditions of 0.41 in fuel/air ratio at different exhaust gas recirculation (EGR) rate from 0～35%. The experimental results indicated that primary particle were in the range of 17.05nm～18.34nm, which increased with increased EGR rate. As EGR rate increased, aggregate particle size were measured in a narrow range from 120nm to 170nm.

Diesel Engine Intake Condition Control-Oriented Models for Active Fuel Injection Profile Control

2011 ◽  
Author(s):  
Fengjun Yan ◽  
Junmin Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
High Fidelity ◽  
Exhaust Gas ◽  
Engine Model ◽  
Profile Control ◽  
Gas Recirculation

Fueling control in Diesel engines is not only of significance to the combustion process in one particular cycle, but also influences the subsequent dynamics of air-path loop and combustion events, particularly when exhaust gas recirculation (EGR) is employed. To better reveal such inherently interactive relations, this paper presents a physics-based, control-oriented model describing the dynamics of the intake conditions with fuel injection profile being its input for Diesel engines equipped with EGR and turbocharging systems. The effectiveness of this model is validated by comparing the predictive results with those produced by a high-fidelity 1-D computational GT-Power engine model.

Effect of hydraulic flow rate, injection timing, and exhaust gas recirculation on particulate and gaseous emissions in a light-duty diesel engine

2019 ◽  
Vol 234 (5) ◽  
pp. 1279-1293 ◽  
Author(s):  
Khawar Mohiuddin ◽  
Minhoo Choi ◽  
Junkyu Park ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Flow Rate ◽  
Particle Number ◽  
Exhaust Gas Recirculation ◽  
Injection Timing ◽  
Exhaust Gas ◽  
Gaseous Emissions ◽  
Spray Tip Penetration ◽  
Hydraulic Flow ◽  
Gas Recirculation

Nozzle hydraulic flow rate is a critical parameter that affects the combustion process and plays a vital role in the production of emissions from a diesel engine. In this study, injection characteristics, such as normalized injection rate and spray tip penetration, were analyzed for different hydraulic flow rate injectors with the help of spray experiments. To further investigate the effects of hydraulic flow rate on engine-out particulate and gaseous emissions, engine experiments were performed for different values of hydraulic flow rate in multiple injectors. Various operating conditions and loading configurations were examined, and the effects of varying start of injection and exhaust gas recirculation rates for different hydraulic flow rates were analyzed. A separate Pegasor Particle Sensor (PPS-M) sensor was used to measure and collect data on the particle number, and an analysis was conducted to investigate the relation of particle number with hydraulic flow rate, injection timing, and exhaust gas recirculation rate. Results of the spray experiment exhibited a decreasing injection duration and increasing spray tip penetration with increasing hydraulic flow rate. Effect of hydraulic flow rate on combustion and emission characteristics were analyzed from engine experiment results. Least ignition delay was achieved using a smaller hole diameter, retarded injection timing, and lowest EGR%. Higher hydraulic flow rate with retarded injection timing and higher EGR% helped in reduction of NOx emissions and brake-specific fuel consumption, but particulate emissions were increased. Best particulate matter–NOx trade-off was achieved with lowest hydraulic flow rate.

519 Exhaust Characteristics of Diesel Engine with Common Rail Fuel Injection System During Cold Starting

2009 ◽  
Vol 2009.48 (0) ◽  
pp. 173-174
Author(s):  
Junichi MATSUOKA ◽  
Hiromi ISHTTANI ◽  
Kazuhiro HAYASHIDA ◽  
Hiroyuki YAMADA
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System ◽  
Cold Starting
Sign in / Sign up

Export Citation Format

Share Document