scholarly journals Designing the Gas Turbine Cooling System Equipped with Air Coolers

2019 ◽  
Vol 0 (3) ◽  
pp. 24-30
Author(s):  
Alexander Tarasov ◽  
Oksana Lytvynenko ◽  
Irina Myhaylova
Keyword(s):  
Gas Turbine ◽  
Cooling System ◽  
Turbine Cooling ◽  
Gas Turbine Cooling

scholarly journals (Performance of Gas Turbine Cooling System (Radiator) at PLTGU XYZ against Environmental Air Temperature)

2021 ◽  
Vol 5 (1) ◽  
pp. 15-21
Author(s):  
Ni Ketut Caturwati ◽  
Yusvardi Yusuf ◽  
Muhammad Ilham Al Faiz
Keyword(s):  
Gas Turbine ◽  
Air Temperature ◽  
Cooling System ◽  
Ambient Air ◽  
Turbine Cooling ◽  
Average Value ◽  
Ambient Air Temperature ◽  
Gas Turbine Cooling ◽  
Environmental Air ◽  
Operational Data

The heat exchanger is an important component in the gas and steam power plant (PLTGU) industry. One of the most important heat exchangers in gas turbine cooling systems is the gas turbine radiator. The gas turbine radiator functions to cool the cooling water, which circulated to various components of the gas turbine by using environmental air as the cooling medium. The purpose of this study was to determine the effect of environmental temperature on the performance of gas turbine radiators and to compare operational data in 2017 with operational data when the study conducted in 2019. Data collected for 3 days with 2-3 hour intervals. Data processing and analysis shows that the higher the ambient temperature, the higher the radiator effectiveness value. Data in 2017 shows the highest average value of effectiveness obtained at an ambient air temperature of 35 ˚C of 71,274%. Meanwhile, data in 2019 shows the highest average value of effectiveness at an ambient air temperature of 35 ˚C of 58,859%. Thus, the average effectiveness value of gas turbine radiators has decreased by 12,415% from 2017 to 2019

scholarly journals Two-Stage Evaporative Inlet Air Gas Turbine Cooling

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1382
Author(s):  
Obida Zeitoun
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Evaporative Cooling ◽  
Air Cooling ◽  
Vapor Compression ◽  
Two Stage ◽  
Turbine Cooling ◽  
Riyadh City ◽  
Vapor Compression Refrigeration ◽  
Gas Turbine Cooling

Gas turbine inlet air-cooling (TIAC) is an established technology for augmenting gas turbine output and efficiency, especially in hot regions. TIAC using evaporative cooling is suitable for hot, dry regions; however, the cooling is limited by the ambient wet-bulb temperature. This study investigates two-stage evaporative TIAC under the harsh weather of Riyadh city. The two-stage evaporative TIAC system consists of indirect and direct evaporative stages. In the indirect stage, air is precooled using water cooled in a cooling tower. In the direct stage, adiabatic saturation cools the air. This investigation was conducted for the GE 7001EA gas turbine model. Thermoflex software was used to simulate the GE 7001EA gas turbine using different TIAC systems including evaporative, two-stage evaporative, hybrid absorption refrigeration evaporative and hybrid vapor-compression refrigeration evaporative cooling systems. Comparisons of different performance parameters of gas turbines were conducted. The added annual profit and payback period were estimated for different TIAC systems.

Build Direction Effects on Additively Manufactured Channels

2015 ◽  
Author(s):  
Jacob C. Snyder ◽  
Curtis K. Stimpson ◽  
Karen A. Thole ◽  
Dominic Mongillo
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Small Scale ◽  
Turbine Cooling ◽  
Gas Turbine Cooling ◽  
Gas Turbine Heat Transfer ◽  
Manufacturing Techniques ◽  
Traditional Manufacturing

With the advances of Direct Metal Laser Sintering (DMLS), also generically referred to as additive manufacturing, novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.

Scaling Heat-Transfer Coefficients Measured Under Laboratory Conditions to Engine Conditions

2017 ◽  
Author(s):  
T. I.-P. Shih ◽  
C.-S. Lee ◽  
K. M. Bryden
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Gas Turbine ◽  
Scaling Factor ◽  
Rate Of Change ◽  
Transfer Enhancement ◽  
Scaling Factors ◽  
Turbine Cooling ◽  
Pin Fins ◽  
Gas Turbine Cooling

Almost all measurements of the heat-transfer coefficient (HTC) or Nusselt number (Nu) in gas-turbine cooling passages with heat-transfer enhancement features such as pin fins and ribs have been made under conditions, where the wall-to-bulk temperature, Tw/Tb, is near unity. Since Tw/Tb in gas-turbine cooling passages can be as high as 2.2 and vary appreciably along the passage, this study examines if it is necessary to match the rate of change in Tw/Tb when measuring Nu, whether Nu measured at Tw/Tb near unity needs to be scaled before used in design and analysis of turbine cooling, and could that scaling for ducts with heat-transfer enhancement features be obtained from scaling factors for smooth ducts because those scaling factors exist in the literature. In this study, a review of the data in the literature shows that it is unnecessary to match the rate of change in Tw/Tb for smooth ducts at least for the rates that occur in gas turbines. For ducts with heat-transfer enhancement features, it is still an open question. This study also shows Nu measured at Tw/Tb near unity needs to be scale to the correct Tw/Tb before it can be used for engine conditions. By using steady RANS analysis of the flow and heat transfer in a cooling channel with a staggered array of pin fins, the usefulness of the scaling factor, (Tw/Tb)r, from the literature for smooth ducts was examined. Nuengine, computed under engine conditions, was compared with those computed under laboratory conditions, Nulab, and scaled by (Tw/Tb)r; i.e., Nulab,scaled = Nulab (Tw/Tb)r. Results obtained show the error in Nulab,scaled relative to Nuengine can be as high as 36.6% if r = −0.7 and Tw/Tb = 1.573 in the “fully” developed region. Thus, (Tw/Tb)r based on smooth duct should not be used as a scaling factor for Nu in cooling passages with heat-transfer enhancement features. To address this inadequacy, a method is proposed for generating scaling factors, and a scaling factor was developed to scale the heat transfer from laboratory to engine conditions for a channel with pin fins.

Two-Phase Transpiration Cooling

1982 ◽  
Author(s):  
M. A. El-Masri
Keyword(s):  
Gas Turbine ◽  
Transpiration Cooling ◽  
System Behavior ◽  
Two Phase ◽  
Modes Of Operation ◽  
Considerable Potential ◽  
Closed Form Solutions ◽  
Turbine Cooling ◽  
Gas Turbine Cooling ◽  
Hot Surface

Two-phase transpiration is shown to possess considerable potential for gas turbine cooling. In this concept, water fed into a porous component boils within the wall. The resulting steam issues from the hot surface forming the transpiration film. A model for the performance of such a system is developed. Assuming constant properties and a linear reduction of Stanton number with transpiration rate, closed-form solutions are obtained. The governing dimensionless parameters are identified, the system behavior predicted, and the modes of operation delineated. Those are defined as two-phase, partially-flooded, and completely-flooded modes. At low values of a certain “modified Peclet number,” the two-phase mode is unstable and the system tends to flood. Large values of this parameter indicate stable, well-regulated behavior. Discussions on gas turbine applications are presented. A typical numerical example is given in the Appendix.

The Performance Analysis of a Combined Power Plant Implementing Technologies for Enhancing Power and Efficiency

2015 ◽  
Author(s):  
Jumok Won ◽  
Changmin Son ◽  
Changju Kim
Keyword(s):  
Gas Turbine ◽  
Cooling System ◽  
Promising Result ◽  
Load Condition ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Net Benefit ◽  
Turbine Cooling ◽  
The Difference

Combined Cycle Power (CCP) plant using Liquefied Natural Gas (LNG) plays a key role in electric supply including nuclear and coal power generation systems. There is growing demand for enhancing power and efficiency of existing CCP plants. Typically, the power reduction of gas turbine during summer can be recovered if gas turbine intake cooling system can be implemented in existing LNG based CCP plants. Possible approaches for power and efficiency enhancement are being widely studied in global gas turbine society. The present study aims to investigate net benefit of implementing selected technologies for enhancing power and efficiency of an existing LNG based CCP. For a comparative study, selected technologies such as (1) gas turbine intake cooling system, (2) wet cycle (steam injection), and (3) turbine cooling air precooling are implemented to Busan LNG based CCP plant, Republic of Korea. The complete CCP plant is modeled using Gatecycle and its validation against field operation data showed the differences in the generated power and efficiency at the base load condition within 0.5% and the difference in the turbine inlet temperature value less than 3%. Among the selected technologies, the wet cycle (steam injection) showed the most promising result. Its system composition is relatively simple in comparison to the other technologies. Furthermore, it is advantageous to use within a reasonable limit when higher power is required for peak demand of electric power.

Sign in / Sign up

Export Citation Format

Share Document