scholarly journals (Performance of Gas Turbine Cooling System (Radiator) at PLTGU XYZ against Environmental Air Temperature)

2021 ◽  
Vol 5 (1) ◽  
pp. 15-21
Author(s):  
Ni Ketut Caturwati ◽  
Yusvardi Yusuf ◽  
Muhammad Ilham Al Faiz
Keyword(s):  
Gas Turbine ◽  
Air Temperature ◽  
Cooling System ◽  
Ambient Air ◽  
Turbine Cooling ◽  
Average Value ◽  
Ambient Air Temperature ◽  
Gas Turbine Cooling ◽  
Environmental Air ◽  
Operational Data

The heat exchanger is an important component in the gas and steam power plant (PLTGU) industry. One of the most important heat exchangers in gas turbine cooling systems is the gas turbine radiator. The gas turbine radiator functions to cool the cooling water, which circulated to various components of the gas turbine by using environmental air as the cooling medium. The purpose of this study was to determine the effect of environmental temperature on the performance of gas turbine radiators and to compare operational data in 2017 with operational data when the study conducted in 2019. Data collected for 3 days with 2-3 hour intervals. Data processing and analysis shows that the higher the ambient temperature, the higher the radiator effectiveness value. Data in 2017 shows the highest average value of effectiveness obtained at an ambient air temperature of 35 ˚C of 71,274%. Meanwhile, data in 2019 shows the highest average value of effectiveness at an ambient air temperature of 35 ˚C of 58,859%. Thus, the average effectiveness value of gas turbine radiators has decreased by 12,415% from 2017 to 2019

Thermodynamic Evaluation of a 42MW Gas Turbine Power Plant

2014 ◽  
Vol 12 ◽  
pp. 83-94 ◽  
Author(s):  
Henry Egware ◽  
Albert I. Obanor ◽  
Harrison Itoje
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Air Temperature ◽  
Power Plants ◽  
Exergy Analysis ◽  
Ambient Air ◽  
Thermodynamic Evaluation ◽  
Ambient Air Temperature ◽  
Energy And Exergy ◽  
Gas Turbine Power Plant

Energy and exergy analyses were carried out on an active 42MW open cycle gas turbine power plant. Data from the power plant record book were employed in the investigation. The First and Second Laws of Thermodynamics were applied to each component of the gas power plant at ambient air temperature range of 21 - 330C. Results obtained from the analyses show that the energy and exergy efficiencies decrease with increase in ambient air temperature entering the compressor. It was also shown that 66.98% of fuel input and 54.53% of chemical exergy are both lost to the environment as heat from the combustion chamber in the energy and exergy analysis respectively. The energy analysis quantified the efficiency of the plant arising from energy losses , while exergy analysis revealed the magnitude of losses in various components of the plant. Therefore a complete thermodynamic evaluation of gas turbine power plants requires the use of both analytical methods.

An Innovative Inlet Air Cooling System for IGCC Power Augmentation: Part II—Thermodynamic Analysis

2012 ◽  
Author(s):  
Mirko Morini ◽  
Michele Pinelli ◽  
Pier Ruggero Spina
Keyword(s):  
Gas Turbine ◽  
Air Temperature ◽  
Power Plants ◽  
Cooling System ◽  
Ambient Air ◽  
Combined Cycle ◽  
Air Separation ◽  
Air Cooling ◽  
Separation Unit ◽  
Gasification Process

Integrated Gasification Combined Cycles (IGCCs) are energy systems mainly composed of a gasifier and a combined cycle power plant. Since the gasification process usually requires oxygen as the oxidant, the plant also has an Air Separation Unit (ASU). Moreover, a producer gas cleaner unit is always present between the gasifier and the gas turbine. Since these plants are based on gas-steam combined cycle power plants they suffer from a reduction in performance when ambient temperature increases. In this paper, an innovative system for power augmentation in IGCC plants is presented. The system is based on gas turbine inlet air cooling by means of liquid nitrogen spray. In fact, nitrogen is a product of the ASU, but is not always exploited. In the proposed plant, the nitrogen is first chilled and liquefied and then it can be used for inlet air cooling or stored for a postponed use. This system is not characterized by the limits of water evaporative cooling (where the lower temperature is limited by air saturation) and refrigeration cooling (where the effectiveness is limited by pressure drop in the heat exchanger). A thermodynamic model of the system is built by using a commercial code for the simulation of energy conversion systems. A sensitivity analysis on the main parameters (e.g. ambient air temperature, inlet air temperature difference, etc.) is presented. Finally the model is used to study the capabilities of the system by imposing the real temperature profiles of different sites for a whole year.

Exergy Analysis of a Micro-Gas Turbine Fueled with Syngas

2013 ◽  
Vol 465-466 ◽  
pp. 142-148
Author(s):  
Hussain Sadig ◽  
Shaharin Anwar Sulaiman ◽  
Ibrahim Idris
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Air Temperature ◽  
Heat Input ◽  
Ambient Air ◽  
Exergy Destruction ◽  
Exergetic Efficiency ◽  
Micro Gas Turbine ◽  
Ambient Air Temperature ◽  
Excess Air

A theoretical exergetic analysis of a small-scale gas-turbine system fueled with two different syngas fuels is discussed in this paper. For carrying out the analysis, a micro-gas turbine system with a thermal heat input of 50 kW was simulated using ASPEN plus simulator. Quantitative exergy balance was applied for each component in the cycle. The effects of excess air, ambient air temperature, and heat input on the exergy destruction and exergetic efficiency for each component were evaluated and compared with those resulted from fueling the system with liquefied petroleum gas (LPG). For 50 kW heat input and 50% excess air, the total exergy destruction for LPG, Syngas1, and Syngas2 were found to be 17.3, 14.3, and 13.6 kW, respectively. It was found that increasing the excess air ratio to 100% increased the combustion chamber exergetic efficiency by 8%-10% but it reduced the exergetic efficiency of other components. The same trend was observed when tested ambient air temperature. The results also showed a reduction in the combustion chamber exergetic efficiency by 2%-4% when a 20% heat input increase was applied.

Control Strategies for VHTR Gas-Turbine System With Dry Cooling

2012 ◽  
Author(s):  
Hiroyuki Sato ◽  
Xing L. Yan ◽  
Hirofumi Ohashi ◽  
Yukio Tachibana ◽  
Kazuhiko Kunitomi
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Air Temperature ◽  
Control Strategy ◽  
System Analysis ◽  
Ambient Air ◽  
Outlet Temperature ◽  
Generation Efficiency ◽  
Ambient Air Temperature ◽  
Dry Cooling

An original control strategy for very high temperature reactor (VHTR) gas-turbine system with dry cooling against ambient air temperature fluctuation was established in order to enable the freedom of site selection wherever desired without significant drawbacks on the performance. First, the operability of power conversion system and degradation of power generation efficiency were examined considering not only the thermodynamics but also the mechanical efficiency of compressor based on detailed performance map derived from experimental data. Second, control simulations for large ambient temperature fluctuations were conducted by system analysis code with the built-in control strategy. In addition, the sensitivity of power generation efficiency for typical steam cycle with dry cooling to ambient air temperature changes was assessed for the comparison. It was shown that the design goal can be effectively met simply by monitoring and controlling a few of key operating parameters such as reactor outlet temperature, primary coolant pressure. Furthermore, distinctive advantages of the VHTR gas-turbine system over nuclear power plant employing Rankine cycle was demonstrated when installing in inland area.

Treatment of a Municipal Leachate Under Multi-Variable Conditions

1982 ◽  
Vol 17 (1) ◽  
pp. 135-148
Author(s):  
P.T. Wong ◽  
D.S. Mavinic
Keyword(s):  
Air Temperature ◽  
Nutrient Loading ◽  
Ambient Air ◽  
Removal Rates ◽  
Ambient Air Temperature

Abstract The treatability of a municipal leachate (BOD5 = 8090 mg/L) was investigated, by aerobic biostabilization, at a nutrient loading of BOD5:N:P of 100:3.2:1.1. The first stage effluents were subsequently polished by lime-magnesium coagulation. The ranges of ambient air temperature and sludge age studied were 5° to 25°C and 5 to 20 days, respectively. In the biostabilization phase, a BOD5:N:P loading of 100:3.2:1.1 was found to be “adequate” for treatment. Organic and metal removals in the first stage units were excellent. Under all conditions investigated, except for the two units close to washout conditions (5-day sludge age units at 5° and 10°C), BOD5 and COD removals of at least 99.4 and 96.4 percent, respectively, were achieved. Similarly, removal rates for most of the metals monitored were greater than 90 percent. In general, the removal of residual contaminants was not enhanced significantly by the addition of magnesium in the lime-magnesium polishing step.

Sign in / Sign up

Export Citation Format

Share Document