scholarly journals Comparison of Computational Fluid Dynamics and Experimental Power Output of a Micro Horizontal-Axis Wind Turbine

2017 ◽  
Vol 7 (2 (S)) ◽  
pp. 11
Author(s):  
Sanjay Nikhade ◽  
Suhas Kongre ◽  
S. B. Thakre ◽  
S. S. Khandare
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Horizontal Axis ◽  
Speed Ratio ◽  
Power Performance ◽  
Horizontal Axis Wind Turbine ◽  
Computational Fluid Dynamics Cfd

This paper presents a combined experimental and Computational Fluid Dynamics (CFD) simulation of Micro wind Turbine with 2.28 meters rotor Diameter is performed using the FLUENT 16.2 WORKBENCH. A Micro Horizontal Axis Three Blade Wind Turbine was designed, developed and tested for power performance on new airfoil AFN2016 Designed. The three blades were fabricated from glass fiber with a rotor swept area of 3.14 sq.m for the 1-meter length of the blade and angle of attack experimentally determined to be 5º.The blade is designed for tip speed ratio (TSR) of 7. The power out measured for wind speed from 3.0m/s to 9.0 m/s. The comparison of the CFD and experimental results on the relationship between the power obtained and the wind speed of the wind turbine at the wind from 3-9 m/s. It can be clearly seen that the experimental data match quite well again with the numerical analysis and they both demonstrated that the power of wind turbine increasing with wind speed increases.

scholarly journals The effect of using winglets to enhance the performance of swept blades of a horizontal axis wind turbine

2019 ◽  
Vol 11 (9) ◽  
pp. 168781401987831 ◽  
Author(s):  
Mohamed G Khalafallah ◽  
Abdelnaby M Ahmed ◽  
Mohamed K Emam
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Twist Angle ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Cfd Modeling ◽  
Speed Ratio ◽  
Computational Domain ◽  
Horizontal Axis Wind Turbine

One of the recent methods to improve the performance of horizontal axis wind turbine is to attach a winglet at the tip of the blade of these turbines. Winglets reduce the effect of vortex flow at the blade tip and thus improve the performance of the blade. This article presents a parametric study using the computational fluid dynamics (CFD) modeling to investigate the capability of a winglet to increase the turbine power of swept blades as well as straight blades of a horizontal axis wind turbine. The effects of winglet direction, cant angle, and twist angle are studied for two winglet orientations: upstream and downstream directions. The numerical simulation was performed using ANSYS Fluent computational fluid dynamics code. A three-dimensional computational domain, cylindrical rotationally periodic, was used in the computations. The k-ω shear-stress transport turbulence model was adopted to demonstrate turbulence in the flow. Results show that horizontal axis wind turbine with winglet and sweep could enhance more power compared to their equivalent straight or swept blade. The best improvement in the coefficient of power is 4.39% at design tip speed ratio. This is achieved for downstream swept blades with winglets pointing in the upstream direction and having cant and twist angles of 40° and 10°, respectively.

scholarly journals Flow-driven simulation on variation diameter of counter rotating wind turbines rotor

2018 ◽  
Vol 154 ◽  
pp. 01111
Author(s):  
Y. Fredrika Littik ◽  
Y. Heru Irawan ◽  
M. Agung Bramantya
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Angular Velocity ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Speed Ratio ◽  
Axial Distance ◽  
Horizontal Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Computational Fluid Dynamics Cfd

Wind turbines model in this paper developed from horizontal axis wind turbine propeller with single rotor (HAWT). This research aims to investigating the influence of front rotor diameter variation (D1) with rear rotor (D2) to the angular velocity optimal (ω) and tip speed ratio (TSR) on counter rotating wind turbines (CRWT). The method used transient 3D simulation with computational fluid dynamics (CFD) to perform the aerodynamics characteristic of rotor wind turbines. The counter rotating wind turbines (CRWT) is designed with front rotor diameter of 0.23 m and rear rotor diameter of 0.40 m. In this research, the wind velocity is 4.2 m/s and variation ratio between front rotor and rear rotor (D1/D2) are 0.65; 0.80; 1.20; 1.40; and 1.60 with axial distance (Z/D2) 0.20 m. The result of this research indicated that the variation diameter on front rotor influence the aerodynamics performance of counter rotating wind turbines.

scholarly journals Investigation of an Innovative Rotor Modification for a Small-Scale Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2649 ◽  
Author(s):  
Artur Bugała ◽  
Olga Roszyk
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Airflow Distribution

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

A Study of Aerodynamics Force Evaluation of Horizontal Axis Wind Turbine (HAWT) Blade Using 2D and 3D Comparison

2015 ◽  
Author(s):  
Nazia Binte Munir ◽  
Kyoungsoo Lee ◽  
Ziaul Huque ◽  
Raghava R. Kommalapati
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Blade Surface ◽  
Aerodynamic Forces ◽  
Horizontal Axis Wind Turbine ◽  
Computational Fluid Dynamics Cfd ◽  
Experimental Values ◽  
Nrel Phase Vi

The main purpose of the paper is to use Computational Fluid Dynamics (CFD) in 3-D analysis of aerodynamic forces of a Horizontal Axis Wind Turbine (HAWT) blade and compare the 3-D results with the 2-D experimental results. The National Renewable Energy Laboratory (NREL) Phase VI wind blade profile is used as a model for the analysis. The results are compared with the experimental data obtained by NREL at NASA Ames Research Center for the NREL Phase VI wind turbine blade. The aerodynamic forces are evaluated using 3-D Computational Fluid Dynamics (CFD) simulation. The commercial ANSYS CFX and parameterized 3-D CAD model of NREL Phase VI are used for the analysis. The Shear Stress Transport (SST) Gamma-Theta turbulence model and 0-degree yaw angle condition are adopted for CFD analysis. For the case study seven varying wind speeds (5 m/s, 7 m/s, 10 m/s, 13 m/s, 15 m/s, 20 m/s, 25 m/s) with constant blade rotational speed (72 rpm) are considered. To evaluate the 3-D aerodynamic effect sectional pressure coefficient (Cp) and integrated forces about primary axis such as normal, tangential, thrust and torque are evaluated for each of the seven wind speed cases and compared with the NREL experimental values. The numerical difference of values on wind blade surface between this study and 3-D results of NREL wind tunnel test are found negligible. The paper represents an important comparison between the 3-D lift & drag coefficient with the NREL 2-D experimental data. The results shows that though the current study is in good agreement with NREL 3-D experimental values there is large deviation between the NREL 2-D experimental data and current 3-D study which suggests that in case of 3-D analysis of aerodynamic force of blade surface it is better to use NREL 3-D values instead of 2-D experimental values.

scholarly journals Aerodynamic Investigation of a Horizontal Axis Wind Turbine with Split Winglet Using Computational Fluid Dynamics

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4983 ◽  
Author(s):  
Miguel Sumait Sy ◽  
Binoe Eugenio Abuan ◽  
Louis Angelo Macapili Danao
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Renewable Energy ◽  
Wind Turbine ◽  
Renewable Energy Sources ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Blade Tip ◽  
Nrel Phase Vi

Wind energy is one of the fastest growing renewable energy sources, and the most developed energy extraction device that harnesses this energy is the Horizontal Axis Wind Turbine (HAWT). Increasing the efficiency of HAWTs is one important topic in current research with multiple aspects to look at such as blade design and rotor array optimization. This study looked at the effect of wingtip devices, a split winglet, in particular, to reduce the drag induced by the wind vortices at the blade tip, hence increasing performance. Split winglet implementation was done using computational fluid dynamics (CFD) on the National Renewable Energy Lab (NREL) Phase VI sequence H. In total, there are four (4) blade configurations that are simulated, the base NREL Phase VI sequence H blade, an extended version of the previous blade to equalize length of the blades, the base blade with a winglet and the base blade with split winglet. Results at wind speeds of 7 m/s to 15 m/s show that adding a winglet increased the power generation, on an average, by 1.23%, whereas adding a split winglet increased it by 2.53% in comparison to the extended blade. The study also shows that the increase is achieved by reducing the drag at the blade tip and because of the fact that the winglet and split winglet generating lift themselves. This, however, comes at a cost, i.e., an increase in thrust of 0.83% and 2.05% for the blades with winglet and split winglet, respectively, in comparison to the extended blade.

scholarly journals Bio-Inspired Rotor Design Characterization of a Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3515
Author(s):  
J. Gaitan-Aroca ◽  
Fabio Sierra ◽  
Jose Ulises Castellanos Contreras
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Analysis ◽  
Wind Turbine ◽  
Horizontal Axis ◽  
Experimental Results ◽  
Power Coefficient ◽  
Horizontal Axis Wind Turbine ◽  
Thrust Coefficient ◽  
Rotor Design

In this paper, the performance of a biomimetic wind rotor design inspired by Petrea Volubilis seed is presented. Experimentation for this rotor is configured as a horizontal axis wind turbine (HAWT) and numerical analysis is done in order to obtain performance curves with the open-source computational fluid dynamics (CFD) software OpenFoam®. Numerical analysis and experimental results are compared for power Coefficient (Cp) and thrust coefficient (CT). The biomimetic rotor analysis is also compared with experimental results exposed by Castañeda et al. (2011), who were the first to develop those experimentations with this new rotor design. Computational fluid dynamics simulations were performed using an incompressible large Edyy simulation (LES) turbulence models with a localized sub-grid scale (SGS) dynamic one-equation eddy-viscosity. A dynamic mesh based on an arbitrary mesh interface (AMI) was used to simulate rotation and to evaluate flow around rotor blades in order to accurately capture the flow field behavior and to obtain global variables that allow to determine the power potential of this wind rotor turbine. This study will show the potential of this new rotor design for wind power generation.

scholarly journals Combining Computational Fluid Dynamics and Gradient Boosting Regressor for Predicting Force Distribution on Horizontal Axis Wind Turbine

Vibration ◽  
2021 ◽  
Vol 4 (1) ◽  
pp. 248-262
Author(s):  
Nikhil Bagalkot ◽  
Arvind Keprate ◽  
Rune Orderløkken
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Structural Integrity ◽  
Horizontal Axis ◽  
Gradient Boosting ◽  
Force Distribution ◽  
Horizontal Axis Wind Turbine ◽  
Suitable Alternative ◽  
Wind Speeds

The blades of the horizontal axis wind turbine (HAWT) are generally subjected to significant forces resulting from the flow field around the blade. These forces are the main contributor of the flow-induced vibrations that pose structural integrity challenges to the blade. The study focuses on the application of the gradient boosting regressor (GBR) for predicting the wind turbine response to a combination of wind speed, angle of attack, and turbulence intensity when the air flows over the rotor blade. In the first step, computational fluid dynamics (CFD) simulations were carried out on a horizontal axis wind turbine to estimate the force distribution on the blade at various wind speeds and the blade’s attack angle. After that, data obtained for two different angles of attack (4° and 8°) from CFD acts as an input dataset for the GBR algorithm, which is trained and tested to obtain the force distribution. An estimated variance score of 0.933 and 0.917 is achieved for 4° and 8°, respectively, thus showing a good agreement with the force distribution obtained from CFD. High prediction accuracy and less time consumption make GBR a suitable alternative for CFD to predict force at various wind velocities for which CFD analysis has not been performed.

scholarly journals Performance Prediction and Validation of a Small-Capacity Twisted Savonius Wind Turbine

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1721 ◽  
Author(s):  
Hyeonmu Jang ◽  
Insu Paek ◽  
Seungjoo Kim ◽  
Deockjin Jeong
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Performance Test ◽  
Cfd Simulation ◽  
Power Production ◽  
Maximum Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Simulation Results

In this study, an off-grid–type small wind turbine for street lighting was designed and analyzed. Its performance was predicted using a computational fluid dynamics model. The proposed wind turbine has two blades with a radius of 0.29 m and a height of 1.30 m. Ansys Fluent, a commercial computational fluid dynamics solver, was used to predict the performance, and the k-omega SST model was used as the turbulence model. The simulation result revealed a tip-speed ratio of 0.54 with a maximum power coefficient, or an aerodynamic rotor efficiency of 0.17. A wind turbine was installed at a measurement site to validate the simulation, and a performance test was used to measure the power production. To compare the simulation results obtained from the CFD simulation with the measured electrical power performance, the efficiencies of the generator and the controller were measured using a motor-generator testbed. Also, the control strategy of the controller was found from the field test and applied to the simulation results. Comparing the results of the numerical simulation with the experiment, the maximum power-production error at the same wind speed was found to be 4.32%.

Sign in / Sign up

Export Citation Format

Share Document