Effect of Fluid Compressibility on Toughness-Dominated Hydraulic Fractures With Leakoff

SPE Journal ◽  
2018 ◽  
Vol 23 (06) ◽  
pp. 2118-2132 ◽  
Author(s):  
Di Wang ◽  
Mian Chen ◽  
Yan Jin ◽  
Andrew. P. Bunger
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Hydraulic Fractures ◽  
Gas Reservoirs ◽  
Fracturing Fluids ◽  
Fracture Shape ◽  
Carbon Dioxide Co2 ◽  
Fracture Growth ◽  
Fluid Compressibility

Summary Hydraulic fracturing using supercritical carbon dioxide (CO2) has a recognized potential to grow in importance for unconventional oil and gas reservoirs. It is characterized by higher compressibility than traditional liquid-phase hydraulic-fracturing fluids. Motivated by the larger compressibility of supercritical CO2, this paper considers the problem of a hydraulic fracture in which a compressible fluid is injected at a constant rate to drive a hydraulic fracture in a permeable and brittle rock. The two cases of a plane-strain fracture and a penny-shaped fracture are considered. It is shown that for many practical cases, the formation has a large enough fracture toughness that the propagation is in a regime for which the pressure inside the hydraulic fracture can be treated as spatially uniform (“toughness dominated”). Both numerical simulations and analytical solutions for the relevant limiting regimes show that fluid compressibility affects fracture shape only at the very beginning period, which corresponds to the storage regime, and has little effect on fracture growth in the leakoff regime. Overall, because the transition from the storage regime to the leakoff regime is expected to often take place in a short time after the fracture starts propagating, the influence of compressibility in the storage regime is very brief and can be quickly ignored. Therefore, even relatively sizable fluid compressibility has almost no effect on fracture growth in the toughness-dominated regime when leakoff is taken into account.

Some challenges in hydraulic fracturing of tight gas reservoirs: an experimental study

2011 ◽  
Vol 51 (1) ◽  
pp. 499 ◽  
Author(s):  
Vamegh Rasouli ◽  
Mohammad Sarmadivaleh ◽  
Amin Nabipour
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Interaction Mechanism ◽  
Natural Fracture ◽  
Gas Reservoirs ◽  
Tight Sandstone ◽  
True Triaxial ◽  
Rock Types ◽  
Interface Parameters

Hydraulic fracturing is a technique used to enhance production from low quality oil and gas reservoirs. This approach is the key technique specifically in developing unconventional reservoirs, such as tight formations and shale gas. During its propagation, the hydraulic fracture may arrive at different interfaces. The mechanical properties and bounding quality of the interface as well as insitu stresses are among the most significant parameters that determine the interaction mechanism, i.e. whether the hydraulic fracture stops, crosses or experiences an offset upon its arrival at the interface. The interface could be a natural fracture, an interbed, layering or any other weakness feature. In addition to the interface parameters, the rock types of the two sides of the interface may affect the interaction mechanism. To study the interaction mechanism, hydraulic fracturing experiments were conducted using a true triaxial stress cell on two cube samples of 15 cm. Sample I had a sandstone block in the middle surrounded by mortar, whereas in sample II the location of mortar and tight sandstone blocks were changed. The results indicated that besides the effect of the far field stress magnitudes, the heterogeneity of the formation texture and interface properties can have a dominant effect in propagation characteristics of an induced fracture.

A Case Study of Vertical Hydraulic Fracture Growth, Stress Variations with Depth and Shear Stimulation in the Niobrara Shale and Codell Sand, DJ Basin, Colorado

2021 ◽  
pp. 1-34
Author(s):  
Kevin L. McCormack ◽  
Mark D. Zoback ◽  
Wenhuan Kuang
Keyword(s):  
Principal Stress ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Velocity Model ◽  
Growth Stress ◽  
Hydraulic Fractures ◽  
Stress Profile ◽  
Microseismic Events ◽  
Stress Variations ◽  
Fracture Growth

We carried out a geomechanical study of three wells, one each in the Niobrara A, Niobrara C and Codell sandstone to investigate how the state of stress and stress variations with depth affect vertical hydraulic fracture growth and shear stimulation of pre-existing fractures. We demonstrate that the higher magnitudes of measured least principal stress values in the Niobrara A and C shales are the result of viscoplastic stress relaxation. Using a density log and a VTI velocity model developed to accurately locate the microseismic events, we theoretically calculated a continuous profile of the magnitude of the least principal stress with depth. This stress profile explains the apparent vertical hydraulic fracture growth as inferred from the well-constrained depths of associated microseismic events. Finally, we demonstrate that because of the upward propagation of hydraulic fractures from the Niobrara C to the Niobrara A, the latter formation experienced considerably more shear stimulation, which may contribute to the greater production of oil and gas from that formation.

scholarly journals A multi-perforation staged fracturing experimental study on hydraulic fracture initiation and propagation

2020 ◽  
Vol 38 (6) ◽  
pp. 2466-2484
Author(s):  
Jianguang Wei ◽  
Saipeng Huang ◽  
Guangwei Hao ◽  
Jiangtao Li ◽  
Xiaofeng Zhou ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Fracture Initiation ◽  
Fracture Network ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Tight Sandstone ◽  
Heterogeneous Samples ◽  
Initiation And Propagation

Hydraulic fracture initiation and propagation are extremely important on deciding the production capacity and are crucial for oil and gas exploration and development. Based on a self-designed system, multi-perforation cluster-staged fracturing in thick tight sandstone reservoir was simulated in the laboratory. Moreover, the technology of staged fracturing during casing completion was achieved by using a preformed perforated wellbore. Three hydraulic fracturing methods, including single-perforation cluster fracturing, multi-perforation cluster conventional fracturing and multi-perforation cluster staged fracturing, were applied and studied, respectively. The results clearly indicate that the hydraulic fractures resulting from single-perforation cluster fracturing are relatively simple, which is difficult to form fracture network. In contrast, multi-perforation cluster-staged fracturing has more probability to produce complex fractures including major fracture and its branched fractures, especially in heterogeneous samples. Furthermore, the propagation direction of hydraulic fractures tends to change in heterogeneous samples, which is more likely to form a multi-directional hydraulic fracture network. The fracture area is greatly increased when the perforation cluster density increases in multi-perforation cluster conventional fracturing and multi-perforation cluster-staged fracturing. Moreover, higher perforation cluster densities and larger stage numbers are beneficial to hydraulic fracture initiation. The breakdown pressure in homogeneous samples is much higher than that in heterogeneous samples during hydraulic fracturing. In addition, the time of first fracture initiation has the trend that the shorter the initiation time is, the higher the breakdown pressure is. The results of this study provide meaningful suggestions for enhancing the production mechanism of multi-perforation cluster staged fracturing.

scholarly journals Experimental and Theoretical Study on Dynamic Hydraulic Fracture

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 397 ◽  
Author(s):  
Jingnan Dong ◽  
Mian Chen ◽  
Yuwei Li ◽  
Shiyong Wang ◽  
Chao Zeng ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Fluid Velocity ◽  
Crack Tip ◽  
Momentum Balance ◽  
Gas Reservoirs ◽  
Direct Observations ◽  
Total Input ◽  
Theoretical Predictions

Hydraulic fracturing is vital in the stimulation of oil and gas reservoirs, whereas the dynamic process during hydraulic fracturing is still unclear due to the difficulty in capturing the behavior of both fluid and fracture in the transient process. For the first time, the direct observations and theoretical analyses of the relationship between the crack tip and the fluid front in a dynamic hydraulic fracture are presented. A laboratory-scale hydraulic fracturing device is built. The momentum-balance equation of the fracturing fluid is established and numerically solved. The theoretical predictions conform well to the directly observed relationship between the crack tip and the fluid front. The kinetic energy of the fluid occupies over half of the total input energy. Using dimensionless analyses, the existence of equilibrium state of the driving fluid in this dynamic system is theoretically established and experimentally verified. The dimensionless separation criterion of the crack tip and the fluid front in the dynamic situation is established and conforms well to the experimental data. The dynamic analyses show that the separation of crack tip and fluid front is dominated by the crack profile and the equilibrium fluid velocity. This study provides a better understanding of the dynamic hydraulic fracture.

The effect of gravity on the shape and direction of vertical hydraulic fractures

2020 ◽  
Vol 60 (2) ◽  
pp. 668
Author(s):  
Saeed Salimzadeh
Keyword(s):  
Hydraulic Fracturing ◽  
Shale Gas ◽  
Hydraulic Fracture ◽  
Hydraulic Fractures ◽  
Fluid Viscosity ◽  
Gas Reservoirs ◽  
Unconventional Gas Reservoirs ◽  
Fracture Fluid ◽  
Fracture Opening

Australia has great potential for shale gas development that can reshape the future of energy in the country. Hydraulic fracturing has been proven as an efficient method to improve recovery from unconventional gas reservoirs. Shale gas hydraulic fracturing is a very complex, multi-physics process, and numerical modelling to design and predict the growth of hydraulic fractures is gaining a lot of interest around the world. The initiation and propagation direction of hydraulic fractures are controlled by in-situ rock stresses, local natural fractures and larger faults. In the propagation of vertical hydraulic fractures, the fracture footprint may extend tens to hundreds of metres, over which the in-situ stresses vary due to gravity and the weight of the rock layers. Proppants, which are added to the hydraulic fracturing fluid to retain the fracture opening after depressurisation, add additional complexity to the propagation mechanics. Proppant distribution can affect the hydraulic fracture propagation by altering the hydraulic fracture fluid viscosity and by blocking the hydraulic fracture fluid flow. In this study, the effect of gravitational forces on proppant distribution and fracture footprint in vertically oriented hydraulic fractures are investigated using a robust finite element code and the results are discussed.

scholarly journals Numerical simulation of the laws of fracture propagation of multi-hole linear co-directional hydraulic fracturing

2021 ◽  
pp. 014459872198899
Author(s):  
Weiyong Lu ◽  
Changchun He
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Minimum Principle ◽  
Fracture Propagation ◽  
Axial Direction ◽  
Rock Breaking ◽  
Hydraulic Fractures ◽  
Directional Hydraulic Fracturing ◽  
Fracture Intersection ◽  
Expansion Stage

Directional rupture is one of the most important and most common problems related to rock breaking. The goal of directional rock breaking can be effectively achieved via multi-hole linear co-directional hydraulic fracturing. In this paper, the XSite software was utilized to verify the experimental results of multi-hole linear co-directional hydraulic fracturing., and its basic law is studied. The results indicate that the process of multi-hole linear co-directional hydraulic fracturing can be divided into four stages: water injection boost, hydraulic fracture initiation, and the unstable and stable propagation of hydraulic fracture. The stable expansion stage lasts longer and produces more microcracks than the unstable expansion stage. Due to the existence of the borehole-sealing device, the three-dimensional hydraulic fracture first initiates and expands along the axial direction in the bare borehole section, then extends along the axial direction in the non-bare hole section and finally expands along the axial direction in the rock mass without the borehole. The network formed by hydraulic fracture in rock is not a pure plane, but rather a curved spatial surface. The curved spatial surface passes through both the centre of the borehole and the axial direction relative to the borehole. Due to the boundary effect, the curved spatial surface goes toward the plane in which the maximum principal stress occurs. The local ground stress field is changed due to the initiation and propagation of hydraulic fractures. The propagation direction of the fractures between the fracturing boreholes will be deflected. A fracture propagation pressure that is greater than the minimum principle stress and a tension field that is induced in the leading edge of the fracture end, will aid to fracture intersection; as a result, the possibility of connecting the boreholes will increase.

scholarly journals A numerical investigation on the performance of hydraulic fracturing in naturally fractured gas reservoirs based on stimulated rock volume

2020 ◽  
Vol 10 (8) ◽  
pp. 3333-3345
Author(s):  
Ali Al-Rubaie ◽  
Hisham Khaled Ben Mahmud
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Natural Fracture ◽  
Shear Stresses ◽  
Individual Element ◽  
Natural Fractures ◽  
Gas Reservoirs ◽  
Stimulated Reservoir Volume ◽  
Reservoir Volume ◽  
Naturally Fractured

Abstract All reservoirs are fractured to some degree. Depending on the density, dimension, orientation and the cementation of natural fractures and the location where the hydraulic fracturing is done, preexisting natural fractures can impact hydraulic fracture propagation and the associated flow capacity. Understanding the interactions between hydraulic fracture and natural fractures is crucial in estimating fracture complexity, stimulated reservoir volume, drained reservoir volume and completion efficiency. However, because of the presence of natural fractures with diffuse penetration and different orientations, the operation is complicated in naturally fractured gas reservoirs. For this purpose, two numerical methods are proposed for simulating the hydraulic fracture in a naturally fractured gas reservoir. However, what hydraulic fracture looks like in the subsurface, especially in unconventional reservoirs, remain elusive, and many times, field observations contradict our common beliefs. In this study, the hydraulic fracture model is considered in terms of the state of tensions, on the interaction between the hydraulic fracture and the natural fracture (45°), and the effect of length and height of hydraulic fracture developed and how to distribute induced stress around the well. In order to determine the direction in which the hydraulic fracture is formed strikethrough, the finite difference method and the individual element for numerical solution are used and simulated. The results indicate that the optimum hydraulic fracture time was when the hydraulic fracture is able to connect natural fractures with large streams and connected to the well, and there is a fundamental difference between the tensile and shear opening. The analysis indicates that the growing hydraulic fracture, the tensile and shear stresses applied to the natural fracture.

Utilizing Pseudo Well Connections to Simulate Multi-Stage Hydraulic Fracturing - Example Based On the Study of a Tight Gas Asset

2021 ◽  
Author(s):  
Aamir Lokhandwala ◽  
Vaibhav Joshi ◽  
Ankit Dutt
Keyword(s):  
Hydraulic Fracturing ◽  
Oil And Gas ◽  
Flow Simulation ◽  
Oil And Gas Industry ◽  
Development Plan ◽  
Hydraulic Fractures ◽  
Tight Gas ◽  
Gas Field ◽  
Field Development ◽  
Fracture Modeling

Abstract Hydraulic fracturing is a widespread well stimulation treatment in the oil and gas industry. It is particularly prevalent in shale gas fields, where virtually all production can be attributed to the practice of fracturing. It is also used in the context of tight oil and gas reservoirs, for example in deep-water scenarios where the cost of drilling and completion is very high; well productivity, which is dictated by hydraulic fractures, is vital. The correct modeling in reservoir simulation can be critical in such settings because hydraulic fracturing can dramatically change the flow dynamics of a reservoir. What presents a challenge in flow simulation due to hydraulic fractures is that they introduce effects that operate on a different length and time scale than the usual dynamics of a reservoir. Capturing these effects and utilizing them to advantage can be critical for any operator in context of a field development plan for any unconventional or tight field. This paper focuses on a study that was undertaken to compare different methods of simulating hydraulic fractures to formulate a field development plan for a tight gas field. To maintaing the confidentiality of data and to showcase only the technical aspect of the workflow, we will refer to the asset as Field A in subsequent sections of this paper. Field A is a low permeability (0.01md-0.1md), tight (8% to 12% porosity) gas-condensate (API ~51deg and CGR~65 stb/mmscf) reservoir at ~3000m depth. Being structurally complex, it has a large number of erosional features and pinch-outs. The study involved comparing analytical fracture modeling, explicit modeling using local grid refinements, tartan gridding, pseudo-well connection approach and full-field unconventional fracture modeling. The result of the study was to use, for the first time for Field A, a system of generating pseudo well connections to simulate hydraulic fractures. The approach was found to be efficient both terms of replicating field data for a 10 year period while drastically reducing simulation runtime for the subsequent 10 year-period too. It helped the subsurface team to test multiple scenarios in a limited time-frame leading to improved project management.

Predicting Hydraulic Fracturing in a Carbonate Gas Reservoir in Abu Dhabi Using 1D Mechanical Earth Model: Uncertainty and Constraints

2015 ◽  
Author(s):  
Manhal Sirat ◽  
Mujahed Ahmed ◽  
Xing Zhang
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Natural Fracture ◽  
Abu Dhabi ◽  
Hydraulic Fractures ◽  
Gas Reservoir ◽  
In Situ Stresses ◽  
Tight Carbonate ◽  
Different Depths

Abstract In-situ stress state plays an important role in controlling fracture growth and containment in hydraulic fracturing managements. It is evident that the mechanical properties, existing stress regime and the natural fracture network of its reservoir rocks and the surrounding formations mainly control the geometry, size and containments of produced hydraulic fractures. Furthermore, the three principal in situ stresses' axes swap directions and magnitudes at different depths giving rise to identifying different mechanical bedrocks with corresponding stress regimes at different depths. Hence predicting the hydro-fractures can be theoretically achieved once all the above data are available. This is particularly difficult in unconventional and tight carbonate reservoirs, where heterogeneity and highly stress variation, in terms of magnitude and orientation, are expected. To optimize the field development plan (FDP) of a tight carbonate gas reservoir in Abu Dhabi, 1D Mechanical Earth Models (MEMs), involving generating the three principal in-situ stresses' profiles and mechanical property characterization with depth, have been constructed for four vertical wells. The results reveal the swap of stress magnitudes at different mechanical layers, which controls the dimension and orientation of the produced hydro-fractures. Predicted containment of the Hydro-fractures within the specific zones is likely with inevitable high uncertainty when the stress contrast between Sv, SHmax with Shmin respectively as well as Young's modulus and Poisson's Ratio variations cannot be estimated accurately. The uncertainty associated with this analysis is mainly related to the lacking of the calibration of the stress profiles of the 1D MEMs with minifrac and/or XLOT data, and both mechanical and elastic properties with rock mechanic testing results. This study investigates the uncertainty in predicting hydraulic fracture containment due to lacking such calibration, which highlights that a complete suite of data, including calibration of 1D MEMs, is crucial in hydraulic fracture treatment.

Fracture Initiation and Propagation in a Deep Shale Gas Reservoir Subject to an Alternating-Fluid-Injection Hydraulic-Fracturing Treatment

SPE Journal ◽  
2019 ◽  
Vol 24 (04) ◽  
pp. 1839-1855 ◽  
Author(s):  
Bing Hou ◽  
Zhi Chang ◽  
Weineng Fu ◽  
Yeerfulati Muhadasi ◽  
Mian Chen
Keyword(s):  
Hydraulic Fracturing ◽  
Shale Gas ◽  
Fracture Initiation ◽  
Fluid Injection ◽  
Hydraulic Fractures ◽  
Stress Difference ◽  
Gas Reservoirs ◽  
Complex Fracture ◽  
Initiation And Propagation

Summary Deep shale gas reservoirs are characterized by high in-situ stresses, a high horizontal-stress difference (12 MPa), development of bedding seams and natural fractures, and stronger plasticity than shallow shale. All of these factors hinder the extension of hydraulic fractures and the formation of complex fracture networks. Conventional hydraulic-fracturing techniques (that use a single fluid, such as guar fluid or slickwater) do not account for the initiation and propagation of primary fractures and the formation of secondary fractures induced by the primary fractures. For this reason, we proposed an alternating-fluid-injection hydraulic-fracturing treatment. True triaxial hydraulic-fracturing tests were conducted on shale outcrop specimens excavated from the Shallow Silurian Longmaxi Formation to study the initiation and propagation of hydraulic fractures while the specimens were subjected to an alternating fluid injection with guar fluid and slickwater. The initiation and propagation of fractures in the specimens were monitored using an acoustic-emission (AE) system connected to a visual display. The results revealed that the guar fluid and slickwater each played a different role in hydraulic fracturing. At a high in-situ stress difference, the guar fluid tended to open the transverse fractures, whereas the slickwater tended to activate the bedding planes as a result of the temporary blocking effect of the guar fluid. On the basis of the development of fractures around the initiation point, the initiation patterns were classified into three categories: (1) transverse-fracture initiation, (2) bedding-seam initiation, and (3) natural-fracture initiation. Each of these fracture-initiation patterns had a different propagation mode. The alternating-fluid-injection treatment exploited the advantages of the two fracturing fluids to form a large complex fracture network in deep shale gas reservoirs; therefore, we concluded that this method is an efficient way to enhance the stimulated reservoir volume compared with conventional hydraulic-fracturing technologies.

Sign in / Sign up

Export Citation Format

Share Document