scholarly journals INVESTIGATION OF TRANSIENT NUCLEATE BOILING PROCESSES AND THEIR PRACTICAL USE IN HEAT TREATING INDUSTRY

2017 ◽  
Vol 5 ◽  
pp. 39-48 ◽  
Author(s):  
Nikolai Kobasko
Keyword(s):  
Heat Transfer ◽  
Linear Function ◽  
Thermal Process ◽  
New Technologies ◽  
Convective Heat Transfer Coefficient ◽  
Heat Treating ◽  
Nucleate Boiling ◽  
Transfer Coefficients ◽  
Inconel 600 ◽  
Part Dimension

In the paper transient nucleate boiling process is widely discussed. It’s unknown previously and investigated by author characteristics create a basis for designing of new technologies which allow receiving super strengthened materials. Obtained results are also used for appropriate software development to be widely applied for control of technological processes and cooling recipes design. A possibility of transition from real heat transfer coefficients (HTCs) to effective HTCs is discussed in the paper too. It is shown that core temperature of steel parts at the end of transient nucleate boiling (self-regulated thermal process (SRTP)) is a linear function of a part dimension when convective heat transfer coefficient during quenching in liquid media is fixed. Also, it is shown that effective Kondrtajev number Kn is a function of part size and convection intensity and is almost linear function for large sizes of steel parts. Surface temperature at the beginning of self-regulated thermal process and at its end is calculated depending on size and intensity of cooling. Based on obtained new results, it is possible to design DATABASE for liquid quenchants using standard Inconel 600 probe combined with the Liscic/Petrofer probe. Obtained results can be useful for engineers and software designers.

Evaluation of Convective Heat Transfer Coefficient for Pool Boiling of Milk Under Closed Condition

2015 ◽  
Vol 1 (2) ◽  
Author(s):  
Mahesh Kumar ◽  
K. S. Kasana ◽  
Sudhir Kumar ◽  
Om Prakash
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Linear Regression Analysis ◽  
Convective Heat Transfer Coefficient ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Experimental Errors

This research paper reports the study on heat and mass transfer during pool boiling of milk in an aluminum pan under closed conditions. Various indoor experiments were conducted for different heat inputs varying from 240 to 360 W. During heating of milk the evaporated water was condensed at the inner surface of the condensing cover and collected as fresh water. Experimental data were analyzed by using Rohsenow pool boiling correlation with the help of simple linear regression analysis. The convective heat transfer coefficients were estimated in the range of 186.32 to 567.56 W/m2 oC for the heat inputs varying from 240 to 360 W. The nucleate boiling heat flux was observed to increase exponentially with the increase in excess temperature. The experimental errors in terms of percent uncertainty were also evaluated.

The Effects of Nucleate Boiling Versus Film Boiling on Heat Transfer in Power Boiler Tubes

1962 ◽  
Vol 84 (4) ◽  
pp. 365-371 ◽  
Author(s):  
H. S. Swenson ◽  
J. R. Carver ◽  
G. Szoeke
Keyword(s):  
Heat Transfer ◽  
Nucleate Boiling ◽  
Steel Tube ◽  
Heat Fluxes ◽  
Inside Surface ◽  
Film Boiling ◽  
Stainless Steel Tube ◽  
Transfer Coefficients ◽  
Steam Quality ◽  
Heat Transfer Coefficients

In large, subcritical pressure, once-through power boilers heat is transferred to steam and water mixtures ranging in steam quality from zero per cent at the bottom of the furnace to 100 per cent at the top. In order to provide design information for this type of boiler, heat-transfer coefficients for forced convection film boiling were determined for water at 3000 psia flowing upward in a vertical stainless-steel tube, AISI Type 304, having an inside diameter of 0.408 inches and a heated length of 6 feet. Heat fluxes ranged between 90,000 and 180,000 Btu/hr-sq ft and were obtained by electrical resistance heating of the tube. The operation of the experimental equipment was controlled so that nucleate boiling, transition boiling, and stable film boiling occurred simultaneously in different zones of the tube. The film boiling data were correlated with a modified form of the equation Nu = a a(Re)m(Pr)n using steam properties evaluated at inside surface temperature. Results of a second series of heat-transfer tests with tubes having a helical rib on the inside surface showed that nucleate boiling could be maintained to much higher steam qualities with that type of tube than with a smooth-bore tube.

Inverse Determination of the Local Heat Transfer Coefficients for Nucleate Boiling on a Horizontal Cylinder

2003 ◽  
Vol 125 (6) ◽  
pp. 1087-1095 ◽  
Author(s):  
H. Louahlia-Gualous ◽  
P. K. Panday ◽  
E. A. Artioukhine
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pool Boiling ◽  
Gradient Methods ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Nucleate Boiling ◽  
Nucleate Pool Boiling ◽  
Transfer Coefficients ◽  
Iterative Regularization

This article treats the local heat transfer for nucleate pool boiling around the cylinder using the inverse heat conduction analysis. The physical model considers a half section of a cylinder with unknown surface temperature and heat flux density. The iterative regularization and the conjugate gradient methods are used for solving the inverse analysis. The local Nusselt number profiles for nucleate pool boiling are presented and analyzed for different electric heat. The mean Nusselt number estimated by IHCP is closed with the measured values. The results of IHCP are compared to those of Cornewell and Houston (1994), Stephan and Abdelsalam (1980) and Memory et al. (1995). The influence of the error of the measured temperatures and the error in placement of the thermocouples are studied.

scholarly journals FORCED CONVECTION DRYING OF INDIAN GROUNDNUT: AN EXPERIMENTAL STUDY

2017 ◽  
Vol 15 (3) ◽  
pp. 467
Author(s):  
Ravinder Kumar Sahdev ◽  
Mahesh Kumar ◽  
Ashwani Kumar Dhingra
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Forced Convection ◽  
Experimental Error ◽  
Linear Regression Analysis ◽  
Convective Heat Transfer Coefficient ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Evaporative Heat Transfer

In this paper, convective and evaporative heat transfer coefficients of the Indian groundnut were computed under indoor forced convection drying (IFCD) mode. The groundnuts were dried as a single thin layer with the help of a laboratory dryer till the optimum safe moisture storage level of 8 – 10%. The experimental data were used to determine the values of experimental constants C and n in the Nusselt number expression by a simple linear regression analysis and consequently, the convective heat transfer coefficient (CHTC) was determined. The values of CHTC were used to calculate the evaporative heat transfer coefficient (EHTC). The average values of CHTC and EHTC were found to be 2.48 W/m2 oC and 35.08 W/m2 oC, respectively. The experimental error in terms of percent uncertainty was also estimated. The experimental error in terms of percent uncertainty was found to be 42.55%. The error bars for convective and evaporative heat transfer coefficients are also shown for the groundnut drying under IFCD condition.

Pool Boiling Heat Transfer From Plain and Microporous, Square Pin Finned Surfaces in Saturated FC-72

1999 ◽  
Author(s):  
K. N. Rainey ◽  
S. M. You
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Large Scale ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Small Scale ◽  
Surface Microstructure ◽  
Transfer Coefficients ◽  
Microporous Coating ◽  
Nucleate Boiling Heat Transfer

Abstract The present research is an experimental study of “double enhancement” behavior in pool boiling from heater surfaces simulating microelectronic devices immersed in saturated FC-72 at atmospheric pressure. The term “double enhancement” refers to the combination of two different enhancement techniques: a large-scale area enhancement (square pin fin array) and a small-scale surface enhancement (microporous coating). Fin lengths were varied from 0 (flat surface) to 8 mm. Effects of this double enhancement technique on critical heat flux (CHF) and nucleate boiling heat transfer in the horizontal orientation (fins are vertical) are investigated. Results showed significant increases in nucleate boiling heat transfer coefficients with the application of the microporous coating to the heater surfaces. CHF was found to be relatively insensitive to surface microstructure for the finned surfaces except in the case of the surface with 8 mm long fins. The nucleate boiling and CHF behavior has been found to be the result of multiple, counteracting mechanisms: surface area enhancement, fin efficiency, surface microstructure (active nucleation site density), vapor bubble departure resistance, and re-wetting liquid flow resistance.

Prediction of Heat Transfer Coefficients Under Sub-Cooled Boiling Conditions

2000 ◽  
Author(s):  
Edward V. McAssey ◽  
Jinfeng Wu ◽  
Thomas Dougherty ◽  
Bao Wen Yang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Sharp Increase ◽  
Nucleate Boiling ◽  
Prediction Methods ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Abstract Data are presented for sub-cooled boiling of water in the range of two to four atmospheres. The results show that the sharp increase in heat transfer coefficient associated with nucleate boiling occurs at wall superheats of 20 °C to 30 °C. Comparisons between experimental and predicted heat transfer coefficients are also presented. The two prediction methods examined are the Chen correlation and the Kandlikar correlation.

Simulation of Heat Transfer to Turbulent Nanofluid Flow in an Annular Passage

2014 ◽  
Vol 925 ◽  
pp. 625-629 ◽  
Author(s):  
C.S. Oon ◽  
A. Badarudin ◽  
S.N. Kazi ◽  
M. Fadhli
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Titanium Oxide ◽  
Convective Heat Transfer Coefficient ◽  
Hot Water ◽  
Transfer Coefficients ◽  
Ansys Fluent ◽  
Heat Transfer Coefficients

The heat transfer in annular heat exchanger with titanium oxide of 1.0 volume % concentration as the medium of heat exchanger is considered in this study. The heat transfer simulation of the flow is performed by using Computational Fluid Dynamics package, Ansys Fluent. The heat transfer coefficients of water to titanium oxide nanofluid flowing in a horizontal counter-flow heat exchanger under turbulent flow conditions are investigated. The results show that the convective heat transfer coefficient of the nanofluid is slightly higher than that of the base fluid by several percents. The heat transfer coefficient increases with the increase of the mass flow rate of hot water and also the nanofluid.

Heat transfer coefficients for quenching process simulation

2004 ◽  
Vol 120 ◽  
pp. 269-276
Author(s):  
M. Maniruzzaman ◽  
R. D. Sisson
Keyword(s):  
Heat Transfer ◽  
Boundary Condition ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Process Simulation ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Quenching Process

Quenching heat treatment in a liquid medium is a very complex heat transfer process. Heat extraction from the part surface occurs through several different heat transfer mechanisms in distinct temperature ranges, namely, film boiling, partial film boiling (i.e. transition), nucleate boiling and convection. The maximum heat transfer occurs during the nucleate boiling stage. Experimental study shows that, the effective surface heat transfer coefficient varies more than two orders of magnitude with the temperature during the quenching. For quenching process simulation, accurate prediction of the time-temperature history and microstructure evolution within the part largely depends on the accuracy of the boundary condition supplied. The heat transfer coefficient is the most important boundary condition for process simulation. This study focuses on creating a database of heat transfer coefficients for various liquid quenchant-metallic alloy combinations through experimentation using three different quench probes. This database is a web-based tool for use in quench process simulation. It provides at-a-glance information for quick and easy analysis and sets the stage for a Decision Support System (DSS) and Data Mining for heat-treating process.

scholarly journals CONVECTIVE HEAT TRANSFER CHARACTERISTICS OF AQUEOUS TiO2 NANOFLUID UNDER LAMINAR FLOW CONDITIONS

2008 ◽  
Vol 07 (06) ◽  
pp. 325-331 ◽  
Author(s):  
S. M. SOHEL MURSHED ◽  
KAI CHOONG LEONG ◽  
CHUN YANG ◽  
NAM-TRUNG NGUYEN
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Transfer Coefficients ◽  
Enhancement Of Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Constant Wall Heat Flux

This paper reports an experimental investigation into force convective heat transfer of nanofluids flowing through a cylindrical minichannel under laminar flow and constant wall heat flux conditions. Sample nanofluids were prepared by dispersing different volumetric concentrations (0.2–0.8%) of nanoparticles in deionized water. The results showed that both the convective heat transfer coefficient and the Nusselt number of the nanofluid increase considerably with the nanoparticle volume fraction as well as the Reynolds number. Along with the enhanced thermal conductivity of nanofluids, the migration, interactions, and Brownian motion of nanoparticles and the resulting disturbance of the boundary layer are responsible for the observed enhancement of heat transfer coefficients of nanofluids.

1987 Max Jakob Memorial Award Lecture: Dynamics and Stability of Thin Heated Liquid Films

1990 ◽  
Vol 112 (3) ◽  
pp. 538-546 ◽  
Author(s):  
S. G. Bankoff
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Heated Surface ◽  
Nucleate Boiling ◽  
Liquid Films ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Molecular Forces ◽  
Memorial Award ◽  
Film Heat Transfer

This review covers the dynamics and tendency toward rupture of thin evaporating liquid films on a heated surface. Very large heat transfer coefficients can be obtained. The applications include various boiling heat transfer and film cooling devices. A relatively new area for study is heat transfer through ultrathin films, which are less than 100 nm in thickness, and hence subject to van der Waals and other long-range molecular forces. Some recent work employing lubrication theory to obtain an evolution equation for the growth of a surface wave is described. Earlier phenomenological work is briefly discussed, as well as the connection between forced-convection subcooled nucleate boiling and thin-film heat transfer.

Sign in / Sign up

Export Citation Format

Share Document