scholarly journals Fluoride removal efficiency of Tulsi (Ocimum Sanctum) from water

2021 ◽  
Author(s):  
Kefelegn Bayu ◽  
Abraham Geremew ◽  
Wegene Deriba ◽  
Yohannes Mulugeta ◽  
Samuel Wagari ◽  
...  
Keyword(s):  
Drinking Water ◽  
Removal Efficiency ◽  
Natural Water ◽  
Water Samples ◽  
Contact Time ◽  
Ocimum Sanctum ◽  
Fluoride Removal ◽  
Initial Concentration ◽  
Natural Water Samples ◽  
Adsorbent Dose

Abstract Fluoride concentration in drinking water higher than recommended value imposes different health problems and there are advanced and chemical based defluoridation techniques even if they are not feasible for developing countries and have limitations. Due to this, defluoridation by using locally available plants is one of the most efficient and sustainable options. Therefore, the current study was intended to investigate fluoride removal efficiency of Tulsi (Ocimum Sanctum) from water that can be an alternative means to reduce the problem related to its high concentration. A laboratory based experimental study was implemented by using potentiometric determination in Haramaya University. The leaves of Tulsi were collected, washed with tap water, rinsed with distilled water, and then were dried at room temperature, crushed and sieved through 500-μm stain-less steel sieve. The experiments were conducted on artificially fluoridated water by anhydrous fluoride and natural water samples collected from deep well water sources from Adama and Harar town. Data was analyzed using Design of Expert (DOE) and Microsoft excel. Twenty-nine runs for aqueous solution were conducted at different factor combinations and the optimum combinations were applied for natural water samples. The study depicts that plant has an efficiency of removing 68.4% of fluoride from water. The best factor combinations to achieve this efficiency was 0.2 g/100 ml, 22.6 min, 5.7 and 6.6 mg/l, adsorbent dose, contact time, pH and initial concentration respectively. pH and initial concentration have a negative effect and adsorbent dose and contact time have a positive effect on removing fluoride from water. Hence, people living in fluorosis endemic areas can use the processed plant as a de-fluoridating agent to minimize adverse health effects. HIGHLIGHT This research articles paves way to further study to remove contaminants from water, wastewater, which can pose a substantial effect on public health. The study conducted to investigate removal mechanism of fluoride from drinking water with low cost locally available plant and the software technologies were applied to find the optimum conditions at which the adsorbent works best.

Stability of low levels of perchlorate in drinking water and natural water samples

2006 ◽  
Vol 567 (1) ◽  
pp. 108-113 ◽  
Author(s):  
Sarah J. Stetson ◽  
Richard B. Wanty ◽  
Dennis R. Helsel ◽  
Stephen J. Kalkhoff ◽  
Donald L. Macalady
Keyword(s):  
Drinking Water ◽  
Natural Water ◽  
Water Samples ◽  
Natural Water Samples ◽  
Low Levels

scholarly journals An Experimental Study on Biosorption of Fluoride from Water Using LocallyObtained Moringa Oleifera Seeds

2021 ◽  
Vol 19 (1) ◽  
pp. 35-39
Author(s):  
Faheem Akhter ◽  
Arsalan A. Jokhio ◽  
Javed A. Noonari
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Contact Time ◽  
Moringa Oleifera ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Engineering Science ◽  
Environment Friendly ◽  
Experimental Facilities ◽  
Adsorbent Dose

Moringa Oleifera is considered to be a natural bio-adsorbent. Unlike chemical coagulants, Moringa Oleifera seeds are environment friendly with various other advantages. The present study investigated the fluoride removal efficiency of Moringa Oleifera from water. Influence of adsorbent dose (1, 2, 4 g/L), contact time (20, 40 and 60 min) and initial fluoride concentration (2 and 5 mg/L) over removal efficiency were determined and optimized. It was found that increased adsorbent dose and contact time enhanced the removal efficiency which is in agreement with the previous studies. The highest removal of 88.1% was achieved when the adsorbent dose and contact time were optimized to 4 g/L and 60 minutes with an initial fluoride concentration of 2 mg/L. The results showed that Moringa Oleifera can be used as an environment friendly, cheap and effective bio-adsorbent for fluoride removal from aqueous solution. All the experimental facilities were provided by Bio-Fuel Lab, Energy & Environment Department, Quaid-e-Awam University of Engineering, Science and Technology, Nawabshah, Pakistan. The samples were analyzed at the Pakistan Council of Research in Water Resources (PCRWR), Tando Jam, Pakistan.

scholarly journals Removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones

2019 ◽  
Vol 6 (2) ◽  
pp. 81-88 ◽  
Author(s):  
Dariush Naghipour ◽  
Abdoliman Amouei ◽  
Kamran Taher Ghasemi ◽  
Kamran Taghavi
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Contact Time ◽  
Wastewater Treatment Plants ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Pine Cones ◽  
Adsorbent Dose

Background: Metoprolol (MTP) with its low biodegradability is one of the most dominant micropollutant in the effluent of wastewater treatment plants. The aim of this study was to investigate the removal of metoprolol from aqueous solutions by the activated carbon prepared from pine cones. Methods: The pine cones were activated using thermal activation method. Characteristics of the adsorbent were determined using Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM). In this study, the influent of different parameters such as pH, contact time, initial concentrations of metoprolol, adsorbent dose, temperature, adsorption isotherms, and kinetics were investigated. Results: The maximum removal efficiency of MTP (89.2%) was obtained at pH=8.5, adsorbent dose=1.5 g, contact time=60 min, and initial concentration=50 mg/L. By increasing the adsorbent dose, the removal efficiency also increased, but the adsorption capacity decreased, however, by increasing the initial concentration, the removal efficiency decreased, but the adsorption capacity increased. The isotherm experimental data for metoprolol was best fitted using the Langmuir model, and kinetic data were better described by pseudo-second-order kinetic model. The thermodynamic study indicated that the adsorption of MTP by the adsorbent was feasible, spontaneous, and endothermic. Conclusion: MTP removal by the activated carbon prepared from pine cones showed that this natural adsorbent is appropriate for removal of metoprolol from aqueous solutions regarding cost, efficiency, and production method.

scholarly journals Removal of Fluoride from Drinking Water Using Modified Immobilized Activated Alumina

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Aneeza Rafique ◽  
M. Ali Awan ◽  
Ayesha Wasti ◽  
Ishtiaq A. Qazi ◽  
Muhammad Arshad
Keyword(s):  
Drinking Water ◽  
Removal Efficiency ◽  
Activated Charcoal ◽  
Contact Time ◽  
Sol Gel ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Batch Adsorption ◽  
Activated Alumina ◽  
Fluoride Adsorption

The study describes the removal of fluoride from drinking water using modified immobilized activated alumina (MIAA) prepared by sol-gel method. The modification was done by adding a specific amount of alum during the sol formation step. The fluoride removal efficiency of MIAA was 1.35 times higher as compared to normal immobilized activated alumina. A batch adsorption study was performed as a function of adsorbent dose, contact time, stirring rate, and initial fluoride concentration. More than 90% removal of fluoride was achieved within 60 minutes of contact time. The adsorption potential of MIAA was compared with activated charcoal which showed that the removal efficiency was about 10% more than the activated charcoal. Both the Langmuir and Freundlich adsorption isotherms fitted well for the fluoride adsorption on MIAA with the regression coefficientR2of 0.99 and 0.98, respectively. MIAA can both be regenerated thermally and chemically. Adsorption experiments using MIAA were employed on real drinking water samples from a fluoride affected area. The study showed that modified immobilized activated alumina is an effective adsorbent for fluoride removal.

scholarly journals Efficient removal of arsenic from water by dielectrophoresis-assisted adsorption

2018 ◽  
Vol 19 (4) ◽  
pp. 1066-1072
Author(s):  
Q. H. Jin ◽  
C. Y. Cui ◽  
H. Y. Chen ◽  
Y. Wang ◽  
J. F. Geng ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Solution Ph ◽  
Residual Concentration ◽  
Initial Concentration ◽  
Weight Percentage ◽  
Before And After ◽  
High Concentrations ◽  
Plant Ash ◽  
Adsorbent Dose

Abstract Adsorption (ADS) and dielectrophoresis (DEP) techniques were combined (ADS/DEP) to efficiently remove As(V) in industrial wastewater. Fly ash, activated carbon, corncob and plant ash were tested to determine the best adsorbent by their adsorption capacity. Plant ash showed the highest adsorption capacity compared with the others. Different parameters such as solution pH and adsorbent dose were explored. The maximum As(V) removal efficiency was 91.4% at the optimized conditions (pH 9.0, adsorbent dose 5 g/L) when the initial concentration of As(V) was 15 mg/L. With the ADS/DEP technique, the plant ash particles with adsorbed As(V) were trapped on the electrodes in a DEP device. The ADS/DEP process could increase the removal efficiency of As(V) to 94.7% at 14 V even when the initial concentration of As(V) was 15 mg/L. And the residual concentration of As(V) decreased to 0.34 mg/L after two series of the ADS/DEP process. The adsorbents before and after DEP were examined by scanning electron microscope (SEM) and energy dispersive X-ray (EDX) analysis. After the DEP process, the weight percentage of As(V) on the adsorbent surface increased to 0.96% from 0.5%. The ADS/DEP process could be a new efficient way to remove arsenic pollutant at high concentrations.

Sign in / Sign up

Export Citation Format

Share Document