scholarly journals Efficient solar heterogeneous photocatalytic degradation of metronidazole using heterojunction semiconductors hybrid nanocomposite, layered double hydroxides

2020 ◽  
Vol 82 (12) ◽  
pp. 2837-2846
Author(s):  
Farid Aoudjit ◽  
Fouzia Touahra ◽  
Lamine Aoudjit ◽  
Ouiza Cherifi ◽  
Djamilla Halliche
Keyword(s):  
Photocatalytic Degradation ◽  
Layered Double Hydroxides ◽  
Environmental Remediation ◽  
Solar Irradiation ◽  
Precipitation Method ◽  
Catalyst Loading ◽  
X Ray ◽  
Constant Ph ◽  
Co Precipitation ◽  
Double Hydroxides

Abstract This study focuses on the synthesis of various nanocomposites with heterojunction structures, MgAl-LDH (LDH = layered double hydroxides) hybrid with semiconductor such as MoO3 and CuO. These solids were synthesized by co-precipitation method at constant pH and have been characterized extensively using atomic absorption spectroscopy (AAS), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and transmission electron microscopy-energy dispersive X-ray (TEM-EDX) methods. The catalytic activity of nanocomposites was tested in the photocatalytic degradation under solar irradiation of emerging pollutants as the pharmaceutical metronidazole (MNZ). The experimental parameters, including initial MNZ concentration, the nature of oxide incorporate in the photocatalyst, catalyst loading were explored. All the synthesized samples showed high photocatalytic performances; the highest photocatalysis efficiency was achieved with the photocatalyst dose 1.5 g/L and initial MNZ concentration of 10 mg/L at neutral pH. The photocatalytic experimental results were fitted very well to the Langmuir-Hinshelwood model. From the obtained results the calcined LDH/semiconductors could be efficient for the photocatalytic process under solar irradiation of pharmaceuticals and may contribute in environmental remediation.

scholarly journals Gas-Phase Hydrogenation of Furfural to Furfuryl Alcohol over Cu-ZnO-Al2O3 Catalysts Prepared from Layered Double Hydroxides

Catalysts ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 486
Author(s):  
Guillermo R. Bertolini ◽  
Carmen P. Jiménez-Gómez ◽  
Juan Antonio Cecilia ◽  
Pedro Maireles-Torres
Keyword(s):  
Gas Phase ◽  
Aging Time ◽  
Layered Double Hydroxides ◽  
Furfuryl Alcohol ◽  
Precipitation Method ◽  
Molar Ratio ◽  
X Ray ◽  
General Chemical ◽  
Co Precipitation ◽  
Double Hydroxides

Several layered double hydroxides (LDHs) with general chemical composition (Cu,Zn)1−xAlx(OH)2(CO3)x/2·mH2O have been synthesized by the co-precipitation method, maintaining a (M2+/M3+) molar ratio of 3, and varying the Cu2+/Zn2+ molar ratio between 0.2 and 6.0. After calcination and reduction steps, Cu/ZnO/Al2O3 catalysts were synthesized. These catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), H2 thermoprogrammed reduction (H2-TPR), N2 adsorption-desorption at −196 °C, N2O titration, X-ray photoelectron miscroscopy (XPS), NH3-thermoprogramed desorption (NH3-TPD) and CO2- thermoprogrammed desorption (CO2-TPD). The characterization data revealed that these catalysts are mainly meso-and macroporous, where Cu, ZnO and Al2O3 are well dispersed. The catalytic results show that these catalysts are active in the gas-phase hydrogenation of furfural, being highly selective to furfuryl alcohol (FOL) and reaching the highest FOL yield for the catalyst with a Cu2+/Zn2+ molar ratio of 1. In an additional study, the influence of the aging time on the synthesis of the LDHs was also evaluated. The catalytic data revealed that the use of shorter aging time in the formation of the LDH has a beneficial effect on the catalytic behavior, since more disordered structures with a higher amount of available Cu sites is obtained, leading to a higher yield towards FOL (71% after 5 h of time-on-stream at 210 °C).

scholarly journals Synthesis of hybrid materials based on layered double hydroxides

2019 ◽  
pp. 4-10
Author(s):  
Olga Nestroinaia ◽  
Oksana Ponomarenko
Keyword(s):  
Hybrid Materials ◽  
Layered Double Hydroxides ◽  
Microwave Method ◽  
Hydrothermal Conditions ◽  
Promising Direction ◽  
X Ray ◽  
Constant Ph ◽  
Co Precipitation ◽  
Double Hydroxides ◽  
Scanning Electron

The use of pesticides adversely affects not only the environment, but also human health. A promising direction in solving this problem is to obtain hybrid materials capable of controlled release of pesticides. Layered double hydroxides (LDHs) can act as a matrix. Layered double hydroxides with intercalated glyphosate anions (MgAl-Gly-LDH) were synthesized by different methods: coprecipitation at constant pH (MgAl-Gly-LDH-c), synthesis under hydrothermal conditions (MgAl-Gly-LDH-ht), microwave method (MgAl-Gly-LDH-mw) and rehydration method (MgAl-Gly-LDH-re). All the synthesized samples were analyzed by X-ray phase analysis (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and Raman spectroscopy. It is shown that the methods of co-precipitation and synthesis under hydrothermal conditions are most suitable for the synthesis of hybrid materials. Samples of MgAl-Gly-LDH-ht and MgAl-Gly-LDH-c have a well-crystallized structure, unlike the sample of MgAl-Gly-LDH-re, in which the LDH phase is practically absent.

scholarly journals Mixed Oxide Layered Double Hydroxide Materials: Synthesis, Characterization and Efficient Application for Mn2+ Removal from Synthetic Wastewater

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4089
Author(s):  
Cristina Modrogan ◽  
Simona Cǎprǎrescu ◽  
Annette Madelene Dǎncilǎ ◽  
Oanamari Daniela Orbuleț ◽  
Eugeniu Vasile ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Layered Double Hydroxides ◽  
Synthetic Wastewater ◽  
Precipitation Method ◽  
Metallic Ions ◽  
Materials Synthesis ◽  
Experimental Conditions ◽  
Edx Analysis ◽  
Co Precipitation ◽  
Double Hydroxides

Magnesium–aluminum (Mg-Al) and magnesium–aluminum–nickel (Mg-Al-Ni) layered double hydroxides (LDHs) were synthesized by the co-precipitation method. The adsorption process of Mn2+ from synthetic wastewater was investigated. Formation of the layered double hydroxides and adsorption of Mn2+ on both Mg-Al and Mg-Ni-Al LDHs were observed by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometry (EDX) analysis. XRD patterns for prepared LDHs presented sharp and symmetrical peaks. SEM studies revealed that Mg-Al LDH and Mg-Al-Ni LDH exhibit a non-porous structure. EDX analysis showed that the prepared LDHs present uniformly spread elements. The adsorption equilibrium on these LDHs was investigated at different experimental conditions such as: Shaking time, initial Mn2+ concentration, and temperatures (10 and 20 °C). The parameters were controlled and optimized to remove the Mn2+ from synthetic wastewater. Adsorption isotherms of Mn2+ were fitted by Langmuir and Freundlich models. The obtained results indicated that the isotherm data fitted better into the Freundlich model than the Langmuir model. Adsorption capacity of Mn2+ gradually increased with temperature. The Langmuir constant (KL) value of Mg-Al LDH (0.9529 ± 0.007 L/mg) was higher than Mg-Al-Ni LDH (0.1819 ± 0.004 L/mg), at 20 °C. The final adsorption capacity was higher for Mg-Al LDH (91.85 ± 0.087%) in comparison with Mg-Al-Ni LDH (35.97 ± 0.093%), at 20 °C. It was found that the adsorption kinetics is best described by the pseudo-second-order model. The results indicated that LDHs can be considered as a potential material for adsorption of other metallic ions from wastewater.

scholarly journals Photocatalytic Degradation of 2,4,6-Trichlorophenol by MgO–MgFe2O4 Derived from Layered Double Hydroxide Structures

Catalysts ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 454 ◽  
Author(s):  
Esthela Ramos-Ramírez ◽  
Francisco Tzompantzi-Morales ◽  
Norma Gutiérrez-Ortega ◽  
Héctor G. Mojica-Calvillo ◽  
Julio Castillo-Rodríguez
Keyword(s):  
Photocatalytic Degradation ◽  
Layered Double Hydroxides ◽  
X Ray Diffraction ◽  
Application Study ◽  
Toxic Compounds ◽  
X Ray ◽  
Thermally Activated ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Scanning Electron

In recent years, the search for solutions for the treatment of water pollution by toxic compounds such as phenols and chlorophenols has been increasing. Phenols and their derivatives are widely used in the manufacture of pesticides, insecticides, paper, and wood preservers, among other things. Chlorophenols are partially biodegradable but not directly photodegradable by sunlight and are extremely toxic—especially 2,4,6-trichlorophenol, which is considered to be potentially carcinogenic. As a viable proposal to be applied in the treatment of water contaminated with 2,4,6-trichlorophenol, this paper presents an application study of the thermally activated Mg/Fe layered double hydroxides as photocatalysts for the mineralization of this contaminant. Activated Mg/Fe layered double hydroxides were characterized by X-ray diffraction, thermal analysis, N2 physisorption, and scanning electron microscopy with X-ray dispersive energy. The results of the photocatalytic degradation of 2,4,6-trichlorophenol in aqueous solution showed good photocatalytic activity, with an efficiency of degradation of up to 93% and mineralization of 82%; degradation values which are higher than that of TiO2-P25, which only reached 18% degradation. The degradation capacity is attributed to the structure of the MgO–MgFe2O4 oxides derived from double laminate hydroxide Mg/Fe. A path of degradation based on a mechanism of superoxide and hollow radicals is proposed.

Enhanced catalytic phenol hydroxylation by CuZnFeAl layered double hydroxides: synergistic effects of Cu+ and oxygen vacancies

2021 ◽  
Vol 45 (1) ◽  
pp. 179-188
Author(s):  
Yong Jiang ◽  
Wenlong Xu ◽  
Jinhua Liang ◽  
Jiecan Shen ◽  
Xiaomin Fu ◽  
...  
Keyword(s):  
Layered Double Hydroxides ◽  
Oxygen Vacancies ◽  
Synergistic Effects ◽  
Phenol Oxidation ◽  
Precipitation Method ◽  
Phenol Hydroxylation ◽  
Co Precipitation ◽  
Double Hydroxides

In this work, a series of CuZnFeAl-LDH catalysts for phenol oxidation to dihydroxybenzene have been prepared through a co-precipitation method.

Effect of Doped Iron on Fluoride Sorption by Calcined MgAlFe-CO3 Layered Double Hydroxides

2013 ◽  
Vol 681 ◽  
pp. 21-25
Author(s):  
Yu Bing Pu ◽  
Jia Rui Wang ◽  
Hong Zheng ◽  
Peng Cai ◽  
Si Yuan Wu
Keyword(s):  
Layered Double Hydroxides ◽  
Synthetic Wastewater ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Fluoride Removal ◽  
Maximum Sorption Capacity ◽  
Fluoride Adsorption ◽  
Maximum Sorption ◽  
Co Precipitation ◽  
Double Hydroxides

A series of MgAlFe-CO3 layered double hydroxides (LDHs) were successfully prepared by co-precipitation method. With synthetic wastewater, the effect of doped iron on fluoride sorption by calcined MgAlFe-CO3 layered double hydroxides (CLDH) under different pH and contact time conditions was investigated. The sorption isotherm data were fitted well to Langmuir isotherm at 25 °C. The maximum sorption capacity of fluoride on CLDH increases first and then decreases with the increase of Fe/Al molar ratio and attains maximum of 71.94 mg/g when Fe/Al molar ratio is 1:2, although doped iron is unfavorable to the regeneration of original layered structure for CLDH after fluoride adsorption. No aluminium in the solution after fluoride adsorption was detected when Fe/Al molar ratio is equal to or larger than 1:2. The results indicate that CLDH with proper Fe/Al molar ratio is a promising candidate as an adsorbent material for fluoride removal from aqueous solutions.

Nanoparticles of Cu–Co alloy derived from layered double hydroxides and their catalytic performance for higher alcohol synthesis from syngas

RSC Advances ◽  
2015 ◽  
Vol 5 (72) ◽  
pp. 58804-58812 ◽  
Author(s):  
Ang Cao ◽  
Guilong Liu ◽  
Yizhi Yue ◽  
Lihong Zhang ◽  
Yuan Liu
Keyword(s):  
Layered Double Hydroxides ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Higher Alcohol Synthesis ◽  
Higher Alcohol ◽  
Alcohol Synthesis ◽  
Co Precipitation ◽  
Double Hydroxides

A series of layered double hydroxides (LDHs) with different Cu/Co ratios were prepared according to the co-precipitation method and used as catalyst precursors for higher alcohol synthesis.

Photocatalytic decolourization of methylene blue using [Zn-Al] layered double hydroxides synthesized at different molar cationic ratios

Clay Minerals ◽  
2017 ◽  
Vol 52 (2) ◽  
pp. 203-215 ◽  
Author(s):  
Kaouther Abderrazek ◽  
Najoua Frini Srasra ◽  
Ezzeddine Srasra
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Layered Double Hydroxides ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Molar Ratios ◽  
Constant Ph ◽  
Double Hydroxides

Abstract[Zn-Al] layered double hydroxides (LDH) with cationic molar ratios of R = Zn/Al 1–5 were synthesized by the coprecipitation method at constant pH = 10. The samples synthesized and their derived forms obtained after calcination at 500°C and at 900°C (denoted Zn-Al-R, Zn-Al-R-500 and Zn-Al-R-900, respectively), were characterized by X-ray diffraction (XRD), inductively coupled plasmamass spectrometry, scanning electron microscopy, energy-dispersive X-ray spectroscopy, diffuse reflectance spectroscopy and nitrogen physisorption at −196°C. The XRD study showed: (1) the presence of accessory ZnO with the LDH in samples synthesized with R ≥ 3; and (2) the lamellar structure was destroyed at 500°C which made room for a poorly ordered ZnO phase, while calcination at 900°C yielded well crystallized ZnO and ZnAl2O4. The photocatalytic activity of the calcined and the unheated samples was evaluated for the decolourization of methylene blue. The photocatalytic activity was dependent on the cationic ratio R and on the calcination temperature. The sample Zn-Al-3 displayed maximum photocatalytic activity. Calcination at 500 and 900°C improved the photocatalytic activity of LDH synthesized at R = 1 and 2.

Sign in / Sign up

Export Citation Format

Share Document