wLEACH: Real-time Meteorological Data based Wind LEACH

Author(s):  
Chaudhari Monali ◽  
Bhaskar A. A

Introduction: Nowadays, Wireless Sensor Network (WSN) plays an important role in various fields. The limited power capability of the sensor nodes in the WSN brings constraints on the performance of the network. Low energy adaptive clustering hierarchy (LEACH) is a promising protocol for WSN that suffers from higher energy consumption. Objective: The primary objective of this study is to give an alternate harvesting resource power to sensor nodes in the LEACH algorithm which can be equally capable of providing the same or some time better results. Method: This study is based on real-time meteorological data. A real-time wind speed data is taken for the starting of a day to the end of the day on an hourly basis from the weather forecast. Now to convert this rotational energy into electrical energy, we used two types of wind turbines. For the proposed methodology, a micro wind turbine generator and 300watt wind turbine are used. Then this converted electrical energy is given to sensor nodes. For the clustering, the wind power operated nodes are given maximum preference to be elected as the cluster heads based on real-time wind meteorological data. We consider 10 wind-powered sensor nodes. As we increase the number of wind-powered sensor nodes in the network the performance is increased in terms of a lifetime but then increases the complexity of the network. Theses wind-powered nodes remain alive in the network. Since the deployment of the sensor nodes is random each simulation runs for 5 times and the average of first node dead, half node dead and last node dead is considered. Results: The experimental results for the micro wind turbine generator are compared based on with and without the MPPT controller. MPPT controller gives the maximum power by using the tip speed ratio control, power signal feedback control, and hill climb search control method. Therefore, the network lifetime should be higher for the MPPT based wind generator. Network lifetime and Energy consumption are compared for a micro wind turbine generator and 300watt wind turbine. Finally, the performance of the proposed system is compared with the modified solar LEACH implemented using real-time meteorological data. Conclusion: This paper has investigated the wind-based LEACH which uses the real-time meteorological data for the selection of the cluster head. Two types of wind generators are considered for the implementation and it is found that the performance of the commercial 300W wind turbine and the micro wind turbine with and without MPPT are almost similar since the data from both wind turbines are given on hourly basis. The performance of the wLEACH is compared with the sLEACH which shows that the network lifespan of the wLEACH is also nearly same compared to the sLEACH. But it is found that wind power generation is cheaper and efficient than solar power generation. So, this proposed wLEACH provides a cost-efficient solution.

2013 ◽  
Vol 2 (2) ◽  
pp. 69-74 ◽  
Author(s):  
A.K. Rajeevan ◽  
P.V. Shouri ◽  
Usha Nair

A wind turbine generator output at a specific site depends on many factors, particularly cut- in, rated and cut-out wind speed parameters. Hence power output varies from turbine to turbine. The objective of this paper is to develop a mathematical relationship between reliability and wind power generation. The analytical computation of monthly wind power is obtained from weibull statistical model using cubic mean cube root of wind speed. Reliability calculation is based on failure probability analysis. There are many different types of wind turbinescommercially available in the market. From reliability point of view, to get optimum reliability in power generation, it is desirable to select a wind turbine generator which is best suited for a site. The mathematical relationship developed in this paper can be used for site-matching turbine selection in reliability point of view.


Author(s):  
Zenachew Muluneh Hailemariam ◽  
Roberto Leidhold ◽  
Gebremichael Teame Tesfamariam

Author(s):  
FRANSISCO DANANG WIJAYA ◽  
I WAYAN ADIYASA ◽  
EKRAR WINATA

ABSTRAKRasio elektrifikasi di Indonesia belum mencapai 100%, penyebabnya antara lain masalah lokasi di daerah terpencil atau kepulauan dan mahalnya biaya operasi PLTD. Salah satu solusi adalah membangkitkan listrik berbasis energi terbarukan setempat. Tahap awal pemanfaatan energi terbarukan perlu dihitung faktor kapasitas (CF). Tujuan penelitian ini menganalisis CF untuk PLTB dengan metode perhitungan analitik berbasis potensi energi angin, spesifikasi teknologi PLTB dan PLTD, profil beban dan energi listrik yang dapat diproduksi untuk pengembangan sistem hibrida dengan mengambil kasus di Elat Pulau Serau Maluku. Hasil perhitungan CF untuk 5 teknologi PLTB yang berbeda dengan variasi ketinggian di Elat telah diverifikasi dengan simulasi menggunakan perangkat lunak HOMER dengan nilai rerata galat -0,030. Semakin tinggi PLTB, nilai CF semakin besar dengan konstanta 0,0030.Kata kunci: elektrifikasi, faktor kapasitas, PLTB, PLTD, sistem hibrida ABSTRACTThe electrification ratio in Indonesia has not reached 100%, the causes include problems with the location in remote areas or islands and the high operating costs of diesel power plant (DPP). One solution is to generate electricity based on local renewable energy. The initial stage of utilizing renewable energy needs to calculate the capacity factor (CF). The purpose of this research is to analyze CF for wind turbine generator (WTG) with analytical calculation methods based on wind energy potential, technology specifications of WTG and DPP, load profiles and electrical energy that can be produced for hybrid system development by taking the case in Elat Serau Island, Maluku. The results of CF calculations for 5 different WTG technologies with altitude variations in Elat have been verified by simulation using HOMER software with a mean error value of -0.030. The higher the WTG, the greater the CF value with a constant of 0.0030.Keywords: electrification, capacity factor, diesel power plant, wind turbine generator, hybrid system


1983 ◽  
Author(s):  
W.F. Sandusky ◽  
J.W. Buck ◽  
D.S. Renne ◽  
D.L. Hadley ◽  
O.B. Abbey ◽  
...  

2014 ◽  
Vol 564 ◽  
pp. 758-763
Author(s):  
N.A. Hamid ◽  
M.F. Suparin ◽  
T. Gokila ◽  
L.S. Ewe

This paper reports on the design cost and scaling model of a small scale superconducting wind turbine generator, where the levelized cost of energy (COE) was calculated. The proposed design of the wind turbine is based on the vertical axis wind turbine (VAWT) type that drives the superconducting generator. VAWT was chosen due to its ability to operate under low wind speed. Wind turbine using superconducting generator was proposed since it is able to enhance magnetic flux within the stator of the generator and consequently improve the performance of the generator. Once the design has been accomplished, all the cost of parts and components must be accounted and contributes to the overall cost of generating electrical energy from the superconducting wind turbine generator. The cost elements include the initial capital cost (ICC), balance of station (BOS), operation and maintenance (O&M), levelized replacement cost (LRC) and annual energy production (AEP). The calculated levelized COE shows that the cost of generating electricity using superconducting wind turbine generator is lower than generating electricity from conventional sources.


Author(s):  
Toshiaki Kanemoto ◽  
Hiromi Mitarai ◽  
Koichi Kubo ◽  
Noboru Aoki ◽  
Nobuyuki Esaki ◽  
...  

Wind is clean, renewable, and homegrown energy source of electric power generation, and has been positively/effectively utilized to cope with the warming global environment. The conventional turbines with large-sized wind rotor generate high output at moderate wind. The power generation of the small-sized wind rotor is low but is suitable for weak wind. That is, the size of the wind rotor must be correctly/appropriately selected in conformity with the wind circumstances. Moreover, the turbines must be equipped with the brake and/or the pitch control mechanisms, in general, to suppress the abnormal rotation and the generated overload at the stronger wind, and to keep good quality of the electric power. To overcome above weak points, the authors have invented the superior wind turbine generator, as shown in Fig. 1. This unit was called “Intelligent Wind Turbine Generator” by the authors, as the rotational speeds of the tandem wind rotors are adjusted pretty well in cooperation with the two armatures of the generator in response to the wind speed. This unit is composed of the large–sized wind rotor, the small-sized wind rotor and the peculiar generator with the inner and the outer armatures without the conventional stator. The front and the rear wind rotors drive the inner and the outer armatures respectively as shown in Fig.1. The rotational torque is counter balanced between the inner and the outer armatures of the generator. The rotational direction and the speed of both wind rotors/armatures are free, and automatically determined in response to the wind circumstance. The superior power generation of the proposed wind turbine generator was verified in the previous report. Continuously, this paper shows the effects of the front wind rotor profiles, the axial distance and the diameter ratio between both wind rotors on the turbine characteristics, in accompanying with the flow conditions around the tandem wind rotors-were experimentally investigated and shows the characteristics of the superior generator.


Sign in / Sign up

Export Citation Format

Share Document