PROCESS OF CAVITY FORMATION AND COLLAPSE UNDER VARIOUS HYDRAULIC FORCES WITH THEIR COUNTERMEASURE TO INTERNAL EROSION

2019 ◽  
Vol 75 (2) ◽  
pp. I_937-I_942
Author(s):  
Kenta KUDAI ◽  
Shinji SASSA ◽  
Soonbo YANG ◽  
Shoya GOTO
Keyword(s):  
Internal Erosion ◽  
Cavity Formation

A TEM study of the effect of oxygen on nanocavity formation and precipitation in rapid - solidified Fe-16Ni-9Cr stainless steels

1994 ◽  
Vol 52 ◽  
pp. 700-701
Author(s):  
S. Wisutmethangoon ◽  
T. F. Kelly ◽  
J.E. Flinn
Keyword(s):  
Stainless Steels ◽  
High Mobility ◽  
Hot Extrusion ◽  
Extrusion Ratio ◽  
Gas Atomization ◽  
Cavity Formation ◽  
Nucleation Sites ◽  
Heat Treated ◽  
Different Types ◽  
Effect Of Oxygen

Vacancies are introduced into the crystal phase during quenching of rapid solidified materials. Cavity formation occurs because of the coalescence of the vacancies into a cluster. However, because of the high mobility of vacancies at high temperature, most of them will diffuse back into the liquid phase, and some will be lost to defects such as dislocations. Oxygen is known to stabilize cavities by decreasing the surface energy through a chemisorption process. These stabilized cavities, furthermore, act as effective nucleation sites for precipitates to form during aging. Four different types of powders with different oxygen contents were prepared by gas atomization processing. The atomized powders were then consolidated by hot extrusion at 900 °C with an extrusion ratio 10,5:1. After consolidation, specimens were heat treated at 1000 °C for 1 hr followed by water quenching. Finally, the specimens were aged at 600 °C for about 800 hrs. TEM samples were prepared from the gripends of tensile specimens of both unaged and aged alloys.

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

scholarly journals Electromagnetic profiling of Owena Dam, Southwestern Nigeria, using very-low-frequency radio fields

2016 ◽  
Vol 63 (4) ◽  
pp. 237-250 ◽  
Author(s):  
Cyril Okpoli ◽  
Raphael Tijani
Keyword(s):  
Low Frequency ◽  
Soil Mass ◽  
Internal Erosion ◽  
Dam Failure ◽  
Real Component ◽  
Southwestern Nigeria ◽  
Very Low Frequency ◽  
Embankment Dams ◽  
Fractured Zones ◽  
Basement Structures

AbstractVery low frequency (VLF) was used to assess variations in overburden composition, bedrock lithology and the concealed basement structures within the bedrock of Owena Dam in Igbara-Oke of the Precambrian Basement Complex of Southwestern Nigeria. Five VLF-electromagnetic (EM) traverses were occupied at 5 m intervals. The VLF normal and filtered real component anomalies identify major geological interfaces suspected to be faults/fractured zones. The points of crossover between the real and imaginary components delineate the fractured zones, which were identified as areas of possible seepage (piping and sloughing). The internal erosion (permeability) of soil mass eventually leads to the formation of an open conduit in the soil, which may lead to failure of the embankment/dam. The fractured zones are suspected to be present at all traverses. In total, 21 fractured zones were identified along the dam embankment, with the deepest occurrence at Traverse 5. These seepage zones cause heterogeneity in the subsurface composition, which could lead to dam failure. The result of the study suggests that VLF is an adequate method of monitoring seepages in embankment dams.

scholarly journals Dam Breach Simulation with the Material Point Method

Computation ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 8
Author(s):  
Chendi Cao ◽  
Mitchell Neilsen
Keyword(s):  
Material Point Method ◽  
Mixture Theory ◽  
Material Point ◽  
Point Method ◽  
Internal Erosion ◽  
Dam Breach ◽  
New Model ◽  
Hencky Strain ◽  
The Impact ◽  
Soil And Water

Dam embankment breaches caused by overtopping or internal erosion can impact both life and property downstream. It is important to accurately predict the amount of erosion, peak discharge, and the resulting downstream flow. This paper presents a new model based on the material point method to simulate soil and water interaction and predict failure rate parameters. The model assumes that the dam consists of a homogeneous embankment constructed with cohesive soil, and water inflow is defined by a hydrograph using other readily available reach routing software. The model uses continuum mixture theory to describe each phase where each species individually obeys the conservation of mass and momentum. A two-grid material point method is used to discretize the governing equations. The Drucker–Prager plastic flow model, combined with a Hencky strain-based hyperelasticity model, is used to compute soil stress. Water is modeled as a weakly compressible fluid. Analysis of the model demonstrates the efficacy of our approach for existing examples of overtopping dam breach, dam failures, and collisions. Simulation results from our model are compared with a physical-based breach model, WinDAM C. The new model can capture water and soil interaction at a finer granularity than WinDAM C. The new model gradually removes the granular material during the breach process. The impact of material properties on the dam breach process is also analyzed.

scholarly journals Analysis of Morphokinetic Parameters of Feline Embryos Using a Time-Lapse System

Animals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 748
Author(s):  
Joanna Kochan ◽  
Agnieszka Nowak ◽  
Barbara Kij ◽  
Sylwia Prochowska ◽  
Wojciech Niżański
Keyword(s):  
Embryo Development ◽  
Embryo Quality ◽  
Time Lapse ◽  
Blastocyst Stage ◽  
Cavity Formation ◽  
Non Invasive ◽  
Morphokinetic Parameters ◽  
Morphological Defects ◽  
Development In Vitro

The aim of this study was to analyze the morphokinetic parameters of feline embryos using a time lapse system. Oocytes matured in vitro were fertilized (IVF) and in vitro cultured in a time lapse-system (Primo Vision®, Gothenburg, Sweden). The first cell division of embryos occurred between 17 h post insemination (hpi) and 38 hpi, with the highest proportion of embryos (46%) cleaving between 21 and 24 hpi. The timing of the first cleavage significantly affected further embryo development, with the highest development occurring in embryos that cleaved at 21–22 hpi. Embryos that cleaved very early (17–18 hpi) developed poorly to the blastocyst stage (2%) and none of the embryos that cleaved later than 27 hpi were able to reach the blastocyst stage. Morphological defects were observed in 48% of the embryos. There were no statistically significant differences between the timing intervals of the first cleavage division and the frequency of morphological defects in embryos. Multiple (MUL) morphological defects were detected in more than half (56%) of the abnormal embryos. The most frequent single morphological defects were cytoplasmic fragmentation (FR) (8%) and blastomere asymmetry (AS) (6%). Direct cleavage (DC) from 1–3 or 3–5 blastomeres, reverse cleavage (RC) and vacuoles were rarely observed (2–3%). The timing of blastocyst cavity formation is a very good indicator of embryo quality. In our study, blastocyst cavity formation occurred between 127–167 hpi, with the highest frequency of hatching observed in blastocysts that cavitated between 142–150 hpi. Blastocysts in which cavitation began after 161 h did not hatch. In conclusion, the timing of the first and second cleavage divisions, the timing of blastocyst cavity formation and morphological anomalies can all be used as early and non-invasive indicators of cat embryo development in vitro.

Sign in / Sign up

Export Citation Format

Share Document