scholarly journals High Performance Multistring Converter Topology for Three-Phase Grid Tied 200 kW Photovoltaic Generating System

2017 ◽  
Vol 1 (2) ◽  
Author(s):  
Mohammad Rustam M. L. ◽  
F. Danang Wijaya
Keyword(s):  
Power Efficiency ◽  
High Performance ◽  
Reactive Power ◽  
Simulation Method ◽  
Operating Conditions ◽  
Total System ◽  
Voltage Reference ◽  
Pv System ◽  
Three Phase ◽  
Converter Topology

Under various external conditions, grid connected PV system performance is strongly affected by the topology that is used to connect a PV system with grid. This research aims to design a multistring based converter topology for three-phase grid connected 200 kW PV system that has a high performance in various operating conditions. Research was done by a simulation method using Matlab-Simulink with performance being evaluated including the generated power, efficiency, power quality in accordance with grid requirements, as well as the power flow. In the simulation, multistring converter topology was designed using two dc-dc boost multistring converters connected in parallel to a centralized of three-phase three-level NPC inverter with the size of the string being shorter and more parallel strings as well as the maximum voltage of the PV array of 273.5 V close to dc voltage reference of 500 V. Each dc-dc boost multistring converter have individual MPPT controllers. The simulation results showed that this multistring converter topology had a high performance in various operating conditions. This due to more power generated by the NPC inverter (> 190 kW) at the time of high power generation on the STC conditions (1000 W/m2, 25 oC), the lowest efficiency of the total system is 95.08 % and the highest efficiency of the total system is 99.4 %, the quality of the power generated in accordance with the requirements of grid, as well as the inverter put more active power to the grid and less reactive power to the grid. The response of the inverter slightly worse for loads with greater reactive power and unbalanced.

scholarly journals Design of Super Twisting Sliding Mode Controller for a Three-Phase Grid-connected Photovoltaic System under Normal and Abnormal Conditions

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3773
Author(s):  
Kamran Zeb ◽  
Tiago Davi Curi Busarello ◽  
Saif Ul Islam ◽  
Waqar Uddin ◽  
Kummara Venkata Guru Raghavendra ◽  
...  
Keyword(s):  
Steady State ◽  
Dynamic Behavior ◽  
Reactive Power ◽  
Sliding Mode ◽  
Operating Conditions ◽  
Photovoltaic System ◽  
Frequency Variation ◽  
Sliding Mode Controller ◽  
Pv System ◽  
Three Phase

The novelty behind the research in this paper is to investigate the Super Twisting Sliding Mode Controller (ST-SMC) for efficiently injecting both active and reactive power under normal and abnormal operating conditions for a three-phase grid-connected photovoltaic (PV) system. The ST-SMC is aimed to inject sinusoidal current to the grid with low Total Harmonic Distortion (THD), to avoid chattering with easy real implementation, and to enhance the quality of disturbance rejection and sensitivity to parameter variation. The test under normal conditions includes initialization, steady state behavior, dynamic behavior, and interrupting the injection of acting and reactive power while the abnormal conditions consists of voltage sag, voltage swell, frequency variation, DC-link variation, and inclusion of 5th harmonics, etc. The phase lock loop used for synchronization is based on a synchronous reference frame that works well under distorted grids and nonideal. Automatic code is generated in PSIM 9.1 for hardware implementation in the DSP board TMS32F28335 from Texas Instruments while code composer studio 6.2.0 is used for debugging. The real time testing is executed using Typhoon Hardware in Loop (HIL) 402 device on the DSP board. The results authenticate the fastness, effectiveness, and robustness for both steady state and dynamic behavior under various scenarios of the designed controller.

scholarly journals Modeling and Design of the Vector Control for a Three-Phase Single-Stage Grid-Connected PV System with LVRT Capability according to the Spanish Grid Code

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2899 ◽  
Author(s):  
Alexis B. Rey-Boué ◽  
N. F. Guerrero-Rodríguez ◽  
Johannes Stöckl ◽  
Thomas I. Strasser
Keyword(s):  
Vector Control ◽  
Reactive Power ◽  
Low Voltage ◽  
Single Stage ◽  
Photovoltaic System ◽  
Lookup Table ◽  
Voltage Sags ◽  
Pv System ◽  
Low Voltage Ride Through ◽  
Three Phase

This article deals with the vector control in dq axes of a three-phase grid-connected photovoltaic system with single-stage topology and low-voltage-ride-through capability. The photovoltaic generator is built using an array of several series-parallel Suntech PV modules and is modeled as a Lookup Table (two-dimensional; 2-D). The requirements adopted when grid voltage sags occur are based in both the IEC 61400-21 European normative and the allowed amount of reactive power to be delivered according to the Spanish grid code, which avoids the disconnection of the inverter under grid faults by a limitation in the magnitude of the three-phase output inverter currents. For this, the calculation of the positive- and negative-sequences of the grid voltages is made and a conventional three-phase Phase-Locked Loop is used for the inverter-grid synchronization, allowing the control of the active and reactive powers solely with the dq components of the inverter currents. A detailed enhanced flowchart of the control algorithm with low-voltage-ride-through capability is presented and several simulations and experiments using Matlab/SIMULINK and the Controller Hardware-in-the-Loop simulation technique, respectively, are run for several types of one- and three-phase voltage sags in order to validate its behavior.

scholarly journals Decoupled Control of Three Phase Grid Connected Solar PV System

2019 ◽  
Vol 9 (2) ◽  
pp. 4218-4222
Keyword(s):  
Solar Energy ◽  
Power Factor ◽  
Control Strategy ◽  
Reactive Power ◽  
Standard Test ◽  
Effective Control ◽  
Solar Pv ◽  
Pv System ◽  
Three Phase ◽  
Decoupled Control

A reliable grid connected Photovoltaic (PV) system require effective control schemes for efficient use of solar energy. This paper presents a three-phase grid tied PV system with decoupled real and reactive power control to achieve desired power factor with Maximum Power Point Tracking (MPPT) controller to get maximum solar energy. The synchronous reference frame (dq) control along with decoupling concept is used to control the DC-AC inverter output, while the Phase Locked Loop (PLL) synchronization technique is used to monitor and synchronize the voltage and current at the grid side. The DC-DC converter with Incremental Conductance (InC) based MPPT model is also designed in this paper due to better accuracy compared to Perturb & Observe (P&O) algorithm. The simulation is performed in MATLAB/SIMULINK and a 31.5 kW PV system is modelled to get 30 kW power with the help of MPPT at Standard Test Conditions (STC). Any power factor value between 0.85 lagging to 0.9 leading can be obtained by changingreference q current in this inverter control strategy. The simulation results show that the change of reactive powerdoes not affecttheactive power values of the system, which verifies the effectiveness of the decoupled control strategy of the inverter.

scholarly journals Fuzzy Logic Control for Low-Voltage Ride-Through Single-Phase Grid-Connected PV Inverter

Energies ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4796 ◽  
Author(s):  
Eyad Radwan ◽  
Mutasim Nour ◽  
Emad Awada ◽  
Ali Baniyounes
Keyword(s):  
Fuzzy Logic ◽  
Output Power ◽  
Single Phase ◽  
Reactive Power ◽  
Low Voltage ◽  
Operating Conditions ◽  
Pv System ◽  
Utilization Factor ◽  
Low Voltage Ride Through ◽  
Active And Reactive Power

This paper presents a control scheme for a photovoltaic (PV) system that uses a single-phase grid-connected inverter with low-voltage ride-through (LVRT) capability. In this scheme, two PI regulators are used to adjust the power angle and voltage modulation index of the inverter; therefore, controlling the inverter’s active and reactive output power, respectively. A fuzzy logic controller (FLC) is also implemented to manage the inverter’s operation during the LVRT operation. The FLC adjusts (or de-rates) the inverter’s reference active and reactive power commands based on the grid voltage sag and the power available from the PV system. Therefore, the inverter operation has been divided into two modes: (i) Maximum power point tracking (MPPT) during the normal operating conditions of the grid, and (ii) LVRT support when the grid is operating under faulty conditions. In the LVRT mode, the de-rating of the inverter active output power allows for injection of some reactive power, hence providing voltage support to the grid and enhancing the utilization factor of the inverter’s capacity. The proposed system was modelled and simulated using MATLAB Simulink. The simulation results showed good system performance in response to changes in reference power command, and in adjusting the amount of active and reactive power injected into the grid.

Experimental Analysis on the Operating Performance of Induction Motor with Unbalance Power Supply Conditions

2014 ◽  
Vol 635-637 ◽  
pp. 1404-1407
Author(s):  
Yuan Xing Zhang ◽  
Fei Li ◽  
Ya Li Shen ◽  
Lei Juan Yang ◽  
Jie Li ◽  
...  
Keyword(s):  
Induction Motor ◽  
Power Supply ◽  
Power Efficiency ◽  
Single Phase ◽  
Reactive Power ◽  
Phase Voltage ◽  
Three Phase ◽  
Unbalanced Voltage ◽  
Negative Sequence Current ◽  
Domestic Appliances

Problems of power quality have been increasingly concerned by the researchers, as the domestic appliances we are usually used are single-phase load, which mainly causes the unbalance of three-phase voltage of power supply. If the induction motor is supplied by three-phase unbalanced voltage, the currents, active and reactive power, efficiency, and losses are affected as the negative-sequence current appears, this paper is emphasized on the induction motor’s characteristics when its’ power supply is three-phase unbalanced voltage by experimental research.

scholarly journals Enhanced Control Scheme for a Three-Phase Grid-Connected PV Inverter under Unbalanced Fault Conditions

Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1247
Author(s):  
Saeid Abbasi ◽  
Ali Asghar Ghadimi ◽  
Amir Hossein Abolmasoumi ◽  
Mohammad Reza Miveh ◽  
Francisco Jurado
Keyword(s):  
Reactive Power ◽  
Control Strategies ◽  
Active Power ◽  
Reactive Control ◽  
Pv System ◽  
Pv Inverter ◽  
Three Phase ◽  
Control Scheme ◽  
Double Grid ◽  
Unbalanced Grid

This paper presents an improved control strategy to cancel the double grid frequency oscillations in the active power, reactive power, and DC-link voltage of a three-phase grid-connected photovoltaic (PV) system under unbalanced grid condition. To achieve these goals, an enhanced positive–negative-sequence control (PNSC) to remove oscillations of active power and an instantaneous active–reactive control (IARC) to mitigate the fluctuations of active and reactive power, simultaneously, are suggested. These methods are also effective to reduce the oscillations of the DC-link voltage. To track the desired unbalanced or harmonic reference currents, improved proportional resonant (PR) current controllers have been designed using the Bode frequency analysis. Simulation studies are carried out via Matlab/Simulink® software to verify the effectiveness of the suggested control strategies.

scholarly journals Solar Pv Fed Grid Connected System With Reactive Power And Harmonics Compensation

2021 ◽  
Vol 12 (3) ◽  
pp. 3417-3428
Author(s):  
M.Balasubramanian Et.al
Keyword(s):  
Distribution System ◽  
Power Efficiency ◽  
Reactive Power ◽  
Renewable Energy Sources ◽  
Solar Pv ◽  
Synchronous Reference Frame ◽  
Three Phase ◽  
Full Power ◽  
Solar Powered ◽  
Power Point

The aim of this paper is to use renewable energy sources to meet the demand for electricity. For DC-AC conversion, a solar-powered three-phase grid-connected system with a boost (DC-DC) converter and three-phase inverter is used. The updated Perturb and Observe (P&O) Algorithm is used to map the solar photovoltaic system's maximum power point. Synchronous Reference Frame-Phase Locked Loop Theory is used to compensate for harmonic and reactive power. This proposed grid-connected system is used to improve the system's power efficiency as well as extract the full power and feed it to the distribution system. Using Matlab tools, the simulation result demonstrates reasonable efficiency.

scholarly journals Nonlinear Robust Backstepping Control for Three-Phase Grid-Connected PV Systems

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Mohamed Habib Boujmil ◽  
Afef Badis ◽  
Mohamed Nejib Mansouri
Keyword(s):  
Control Strategy ◽  
Control Structure ◽  
Control Process ◽  
Backstepping Control ◽  
Operating Conditions ◽  
Cascade Control ◽  
Control Technique ◽  
Pv System ◽  
Pv Systems ◽  
Three Phase

This paper proposes a cascade control structure for three-phase grid-connected Photovoltaic (PV) systems. The PV system consists of a PV Generator, DC/DC converter, a DC link, a DC/AC fully controlled inverter, and the main grid. For the control process, a new control strategy using nonlinear Backstepping technique is developed. This strategy comprises three targets, namely, DC/DC converter control; tight control of the DC link voltage; and delivering the desired output power to the active grid with unity power factor (PF). Moreover, the control process relies mainly on the formulation of stability based on Lyapunov functions. Maximizing the energy reproduced from a solar power generation system is investigated as well by using the Perturb and Observe (P&O) algorithm. The Energetic Macroscopic Representation (EMR) and its reverse Maximum Control Structure (MCS) are used to provide, respectively, an instantaneous average model and a cascade control structure. The robust proposed control strategy adapts well to the cascade control technique. Simulations have been conducted using Matlab/Simulink software in order to illustrate the validity and robustness of the proposed technique under different operating conditions, namely, abrupt changing weather condition, sudden parametric variations, and voltage dips, and when facing measurement uncertainties. The problem of controlling the grid-connected PV system is addressed and dealt by using the nonlinear Backstepping control.

The Role of Dissolved and Nascent Air in Oil-Hydraulic Systems

2000 ◽  
Author(s):  
Hansjoerg Stern
Keyword(s):  
Steady State ◽  
High Performance ◽  
Transient Behavior ◽  
Operating Conditions ◽  
Phase System ◽  
Hydraulic Systems ◽  
Three Phase ◽  
Significant Damage ◽  
Water Hydraulic

Abstract In modern, high performance hydraulic systems the transient behavior of dissolving, dissolved and nascent air under changing dynamic conditions of pressure and temperature is emerging as an increasingly important factor, capable of creating undesirable operating conditions. The paper discusses the question of how to predict the performance of pump inlets and valve discharges, where we have known for some time that cavitation and cavitation-like conditions exist and can cause significant damage. The steady state conditions at which nascent air evolves from saturated air-in-oil solutions is normally one or two orders of magnitude above the vapor pressure of the system fluid. To what extent, therefore, is “cavitation” in these systems an air-oil problem? Or is it an oil-vapor problem that is analogous to cavitation in water hydraulic pumps and turbines? Or have we created the combination of the two, a three-phase system of liquid, gas and vapor?

Sign in / Sign up

Export Citation Format

Share Document