scholarly journals Numerical simulation of friction stir welding

2014 ◽  
Vol 18 (3) ◽  
pp. 967-978 ◽  
Author(s):  
Miroslav Mijajlovic ◽  
Dragan Milcic ◽  
Miodrag Milcic
Keyword(s):  
Numerical Simulation ◽  
Friction Stir Welding ◽  
Mechanical Energy ◽  
Parent Material ◽  
Contact Conditions ◽  
Friction Stir ◽  
Influence Of Temperature On ◽  
Mechanical Influence ◽  
Welding Technique ◽  
Good Agreement

Friction stir welding is a solid-state welding technique that utilizes thermo-mechanical influence of the rotating welding tool on parent material resulting with monolith joint-weld. On the contact of welding tool and parent material, significant stirring and deformation of parent material appears, and during this process mechanical energy is partially transformed into heat. The paper describes the software for the numerical simulation of friction stir welding developed at Mechanical Engineering Faculty, University of Nis. Numerical solution for estimation of welding plates temperature is estimated using finite difference method-explicit scheme with adaptive grid, considering influence of temperature on material's conductivity, contact conditions between welding tool and parent material, material flow around welding tool etc. The calculated results are in good agreement with the experimental results.

scholarly journals Temperature based validation of the analytical model for the estimation of the amount of heat generated during friction stir welding

2012 ◽  
Vol 16 (suppl. 2) ◽  
pp. 337-350 ◽  
Author(s):  
Dragan Milcic ◽  
Miroslav Mijajlovic ◽  
Nenad Pavlovic ◽  
Mica Vukic ◽  
Dragan Mancic
Keyword(s):  
Friction Stir Welding ◽  
Analytical Model ◽  
Material Flow ◽  
Mechanical Energy ◽  
Relative Difference ◽  
Parent Material ◽  
Contact Conditions ◽  
Friction Stir ◽  
Influence Of Temperature On ◽  
Welding Technique

Friction stir welding is a solid-state welding technique that utilizes thermomechanical influence of the rotating welding tool on parent material resulting in a monolith joint - weld. On the contact of welding tool and parent material, significant stirring and deformation of parent material appears, and during this process, mechanical energy is partially transformed into heat. Generated heat affects the temperature of the welding tool and parent material, thus the proposed analytical model for the estimation of the amount of generated heat can be verified by temperature: analytically determined heat is used for numerical estimation of the temperature of parent material and this temperature is compared to the experimentally determined temperature. Numerical solution is estimated using the finite difference method - explicit scheme with adaptive grid, considering influence of temperature on material's conductivity, contact conditions between welding tool and parent material, material flow around welding tool, etc. The analytical model shows that 60-100% of mechanical power given to the welding tool is transformed into heat, while the comparison of results shows the maximal relative difference between the analytical and experimental temperature of about 10%.

Numerical Simulation of Plunge Force During the Plunge Phase of Friction Stir Welding and Ultrasonic Assisted FSW

2008 ◽  
Author(s):  
Kwanghyun Park ◽  
Bongsuk Kim ◽  
Jun Ni
Keyword(s):  
Numerical Simulation ◽  
Friction Stir Welding ◽  
High Frequency ◽  
Hybrid Welding ◽  
Ultrasonic Vibrations ◽  
Welding Quality ◽  
Friction Stir ◽  
Ultrasonic Assisted ◽  
Welding Force ◽  
Welding Technique

Ultrasonic assisted friction stir welding (UaFSW) is an hybrid welding technique, where high frequency vibration is superimposed on the movement of a rotating tool. The benefit of using ultrasonic vibration in the FSW process refers to the reduction in the welding force and to the better welding quality. The UaFSW system is being developed and its mechanism needs to be understood using both the experiments and the numerical simulations. In this paper, FE simulations of FSW and UaFSW using ABAQUS/Explicit were carried out to examine plunge forces during the plunge phase of FSW and UaFSW, respectively. First, the simulations of the conventional FSW process were validated. Then, simulation of UaFSW process was performed by imposing sinusoidal horizontal ultrasonic vibrations on the tool.

Experiment and Simulation of Influence of Welding Parameters on Temperature in Friction Stir Welding

2010 ◽  
Vol 44-47 ◽  
pp. 76-80
Author(s):  
Lei Wang ◽  
Jian Jun Zhu
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Temperature Distribution ◽  
Welding Process ◽  
Welding Parameters ◽  
Fem Model ◽  
Friction Stir ◽  
Model Of Friction ◽  
Welding Technique ◽  
Good Agreement

Temperature distribution is the foundation to study friction stir welding technique, influence of welding parameters on temperature was studied through experiment measurement on AA2024-T4 aluminum alloy plates. An instantaneous relative linear velocity based heat source was utilized to build the FEM model of friction stir welding process, good agreement was observed between the measured and simulated thermal profiles. FEM model was also utilized to study effect of welding parameters on temperature distribution.

Effect of Porosity Content on the Weldability of Powder Metal Parts Produced by Friction Stir Welding

2007 ◽  
Vol 534-536 ◽  
pp. 789-792 ◽  
Author(s):  
Adem Kurt ◽  
Ilyas Uygur ◽  
Hakan Ates
Keyword(s):  
Friction Stir Welding ◽  
Powder Metal ◽  
Aluminum Powders ◽  
Friction Stir ◽  
Metal Parts ◽  
Constant Friction ◽  
Sintered Powder ◽  
Hardness Values ◽  
Welding Technique ◽  
Traveling Speed

Friction stir welding technique (FSW) has many advantages in terms of tool design, rotational speed and traveling speed, and can be adjusted in a precise manner. It enables heat input into the system to be controlled. In this study, Aluminum powders were compacted at 350,400 and 450 MPa pressure and sintered at 450 oC temperature for 30 minutes in Ar atmosphere. Sintered powder metal parts were joined to each other by FSW at the speed of 1800 rpm and traveling welding speed 200 mm/min under a constant friction force. The results show that the amount of porosity affects the weldability of powder metallurgy (P/M) parts. Furthermore, the porosity and microstructural evolution of the Aluminum also affected the hardness values of the tested materials.

scholarly journals Friction Stir Welding of AA2024-T3 plate – the influence of different pin types

2015 ◽  
Vol 6 (1) ◽  
pp. 51-55 ◽  
Author(s):  
D. Trimble ◽  
H. Mitrogiannopoulos ◽  
G. E. O'Donnell ◽  
S. McFadden
Keyword(s):  
Friction Stir Welding ◽  
Parent Material ◽  
Micro Hardness ◽  
Workpiece Material ◽  
Friction Stir ◽  
Hardness Tests ◽  
Weld Profile ◽  
Unaffected Parent ◽  
Line Defects ◽  
Tool Pin

Abstract. Some aluminium alloys are difficult to join using traditional fusion (melting and solidification) welding techniques. Friction Stir Welding (FSW) is a solid-state welding technique that can join two plates of material without melting the workpiece material. This proecess uses a rotating tool to create the joint and it can be applied to alumium alloys in particular. Macrostructure, microstructure and micro hardness of friction stir welded AA2024-T3 joints were studied. The influence of tool pin profile on the microstructure and hardness of these joints was examined. Square, triflute and tapered cylinder pins were used and results from each weldment are reported. Vickers micro hardness tests and grain size measurements were taken from the transverse plane of welded samples. Distinct zones in the macrostructure were evident. The zones were identified by transitions in the microstructure and hardness of weld samples. The zones identified across the sample were the the unaffected parent metal, the Heat Affected Zone (HAZ), the Thermo-Mechanicaly Affected Zone (TMAZ), and the Nugget Zone (NZ). Measured hardness values varied through each FSW zone. The hardness in each zone was below that of the parent material. The HAZ had the lowest hardness across the weld profile for each pin type tested. The cylindrical pin consistently produced tunnel and joint-line defects. Pin profiles with flat surface features and/or flutes produced consolidated joints with no defects.

Influence of Tool Geometry and Contact Condition on Friction Stir Welding of Al-Cu Laminated Composites

2013 ◽  
Vol 856 ◽  
pp. 16-21
Author(s):  
R. Beygi ◽  
Mohsen Kazeminezhad ◽  
A.H. Kokabi ◽  
S. Mohammad Javad Alvani ◽  
D. Verdera ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Material Flow ◽  
Laminated Composites ◽  
Flow Behavior ◽  
Tool Geometry ◽  
Contact Conditions ◽  
Friction Stir ◽  
Tool Geometries ◽  
Welding Procedure ◽  
Sem Analyses

In this study friction stir welding of Al-Cu laminated composites were carried out by two different tool geometries. Welding procedure was carried out from both sides of Al and Cu. Analyzing cross section of welds showed that different contact conditions between shoulder and material, offers different material flow behavior which is dependent on the tool geometry. SEM analyses showed that mixing of materials in nugget region is more pronounced in the advancing side. Also XRD results indicated that welding from Cu side, leads to intermetallic formation in mixed regions.

Sign in / Sign up

Export Citation Format

Share Document