scholarly journals Heat transfer performance and friction factor of various nanofluids in a double-tube counter flow heat exchanger

2020 ◽  
Vol 24 (6 Part A) ◽  
pp. 3601-3612
Author(s):  
Dan Zheng ◽  
Jin Wang ◽  
Yu Pang ◽  
Zhanxiu Chen ◽  
Bengt Sunden
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Flow Resistance ◽  
Heat Transfer Performance ◽  
Weight Fraction ◽  
Transfer Performance ◽  
Tube Heat Exchanger ◽  
High Heat Transfer

Experimental research was conducted to reveal the effects of nanofluids on heat transfer performance in a double-tube heat exchanger. With nanoparticle weight fraction of 0.5-2.0% and Reynolds number of 4500-14500, the flow resistance and heat transfer were analyzed by using six nanofluids, i.e., CuO-water, Al2O3-water, Fe3O4-water, ZnO-water, SiC-water, SiO2-water nanofluids. Results show that SiC-water nanofluid with a weight concentration of 1.5% provides the best improvement of heat transfer performance. 1.0% CuO-water and 0.5% SiO2-water nanofluids have lower friction factors in the range of Reynolds number from 4500-14500 compared to the other nanofluids. Based on test results of heat transfer performance and flow resistance, the 1.0% CuO-water nanofluid shows a great advantage due to a relatively high heat transfer performance and a low friction factor. Finally, empirical formulae of Nusselt numbers for various nanofluids were established based on experimental data tested in the double-tube heat exchanger.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

scholarly journals Effect of Magnetic Nanofluids on the Performance of a Fin-Tube Heat Exchanger

2021 ◽  
Vol 11 (19) ◽  
pp. 9261
Author(s):  
Yun-Seok Choi ◽  
Youn-Jea Kim
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Magnetic Fields ◽  
Heat Transfer Performance ◽  
Permanent Magnets ◽  
Convective Heat Transfer Coefficient ◽  
Transfer Performance ◽  
Tube Heat Exchanger ◽  
Improve Heat Transfer ◽  
Fin Tube

As electrical devices become smaller, it is essential to maintain operating temperature for safety and durability. Therefore, there are efforts to improve heat transfer performance under various conditions, such as using extended surfaces and nanofluids. Among them, cooling methods using ferrofluid are drawing the attention of many researchers. This fluid can control the movement of the fluid in magnetic fields. In this study, the heat transfer performance of a fin-tube heat exchanger, using ferrofluid as a coolant, was analyzed when external magnetic fields were applied. Permanent magnets were placed outside the heat exchanger. When the magnetic fields were applied, a change in the thermal boundary layer was observed. It also formed vortexes, which affected the formation of flow patterns. The vortex causes energy exchanges in the flow field, activating thermal diffusion and improving heat transfer. A numerical analysis was used to observe the cooling performance of heat exchangers, as the strength and number of the external magnetic fields were varying. VGs (vortex generators) were also installed to create vortex fields. A convective heat transfer coefficient was calculated to determine the heat transfer rate. In addition, the comparative analysis was performed with graphical results using contours of temperature and velocity.

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

2016 ◽  
Author(s):  
Yan Wang ◽  
Xiang Ling
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Parallel Microchannels

The heat transfer performance of fluid flowing in a microchannel was experimentally studied, to meet the requirement of extremely high heat flux removal of microelectronic devices. There were 10 parallel microchannels with rectangular cross-section in the stainless steel plate, which was covered by a glass plate to observe the fluid flowing behavior, and another heating plate made of aluminum alloy was positioned behind the microchannel. Single phase heat transfer and fluid flow downstream the microchannel experiments were conducted with both deionized water and ethanol. Besides experiments, numerical models were also set up to make a comparison with experimental results. It is found that the pressure drop increases rapidly with enlarging Reynolds number (200), especially for ethanol. With comparison, the flow resistance of pure water is smaller than ethanol. Results also show that the friction factor decreases with Reynolds number smaller than the critical value, while increases the velocity, the friction factor would like to keep little changed. We also find that the water friction factors obtained by CFD simulations in parallel microchannels are much larger than experiment results. With heat flux added to the fluid, the heat transfer performance can be enhanced with larger Re number and the temperature rise could be weaken. Compared against ethanol, water performed much better for heat removal. However, with intensive heat flux, both water and ethanol couldn’t meet the requirement and the temperature at outlet would increase remarkably, extremely for ethanol. These findings would be helpful for thermal management design and optimization.

Measurements of Thermal Performance of the Regenerator of a Cryocooler with a high Number of Transfer Units Value

1996 ◽  
Vol 210 (4) ◽  
pp. 341-352 ◽  
Author(s):  
P-H Chen ◽  
Z-C Chang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Friction Factor ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Transfer Performance ◽  
Thomson Effect ◽  
Empirical Correlations ◽  
External Tube ◽  
Improved Model

Hundreds of stacked wire screens are used in the regenerator matrix of a common cryocooler. The number of transfer units of such a matrix (denoted as NTUm) may well exceed 60. However, most of the earlier studies reported are limited to studies of regenerators with NTUm values less than 60, as the single-blow method was employed to measure the NTUm value of the regenerator matrix. Furthermore, in these earlier studies, the effect of heat transfer from the working fluid to the external tube and the Joule-Thomson effect were neglected. In the present study, three regenerators having high NTUm values have been constructed and a transient single-blow technique has been employed to measure the friction factor and the heat transfer performance of these regenerators. In addition, an improved model has been adopted to correct the shortcomings of the earlier studies. Empirical correlations have been provided for the relation between the friction factor and Reynolds number and between the Nusselt number and Reynolds number. The correlation with smaller NTUm values agreed well with those reported in earlier studies.

scholarly journals Optimization of a micro-channel structure of an elliptical louver fin

2019 ◽  
Vol 23 (4) ◽  
pp. 2429-2436
Author(s):  
Fengye Yang ◽  
Guanghui Zhou ◽  
Pengfei Zhao ◽  
Enhai Liu ◽  
Haijun Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Performance Evaluation ◽  
Flow Resistance ◽  
Heat Transfer Performance ◽  
Channel Structure ◽  
Transfer Performance ◽  
Micro Channel ◽  
Comprehensive Performance ◽  
D Model

The influence of the louver fin?s structure on the heat transfer performance of a parallel flow gas cooler is studied, and a 3-D model for an elliptical louver fin is simulated for analysis of the heat transfer and flow resistance characteristics of the fin. The micro-channel structure of the fin is optimized to give the best comprehensive performance evaluation by suitable choice of fin?s thickness and the space between the adjacent louvers for given range of Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document