scholarly journals Thermal-hydraulic performance of TiO2-water nanofluids in an offset strip fin heat exchanger

2021 ◽  
pp. 63-63
Author(s):  
Emre Elibol ◽  
Oguz Turgut
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Single Phase ◽  
Volume Concentration ◽  
Three Dimensional ◽  
Evaluation Criteria ◽  
Reynolds Numbers ◽  
Tio2 Nanoparticle ◽  
Flow And Heat Transfer ◽  
Offset Strip Fin

The flow and heat transfer characteristics of the TiO2-water nanofluid assuming as a single-phase in the rectangular offset strip fin structure for different Reynolds number (500-1000) and TiO2 nanoparticle volume concentration values (0%-4%) were investigated numerically under three-dimensional, steady state and laminar flow conditions. Simulations were also performed for 1% and 4% nanoparticle volume concentrations of Al2O3-water nanofluid, and the results were compared with those of TiO2-water nanofluid. Results show that when the TiO2-water nanofluid is used, the heat transfer rate, heat transfer coefficient and Nusselt number increase with increasing both Reynolds number and nanoparticle volume concentration, and parallel to these, both pressure loss and pumping power increase. Considering the values of the performance evaluation criteria (PEC) number, it is clear that the use of TiO2-water nanofluid in offset strip fin structure at all Reynolds numbers examined between 1%-4% volume concentration values is quite advantageous. It is observed that TiO2-water nanofluid is much superior to Al2O3-water considering the PEC number. When the Reynolds number is 1000 and the volume concentration value of the TiO2 nanoparticle is 4%, the PEC number value is found to be 1.19, that is, there is a 19% increase compared to water. It is considered that the results of this study can be used as important data on the design of automobile radiators, air-conditioning and defense.

Direct Numerical Simulation of Flow and Heat Transfer From a Sphere in a Uniform Cross-Flow

2000 ◽  
Vol 123 (2) ◽  
pp. 347-358 ◽  
Author(s):  
P. Bagchi ◽  
M. Y. Ha ◽  
S. Balachandar
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Vortex Shedding ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Temperature Fields ◽  
Flow And Heat Transfer

Direct numerical solution for flow and heat transfer past a sphere in a uniform flow is obtained using an accurate and efficient Fourier-Chebyshev spectral collocation method for Reynolds numbers up to 500. We investigate the flow and temperature fields over a range of Reynolds numbers, showing steady and axisymmetric flow when the Reynolds number is less than 210, steady and nonaxisymmetric flow without vortex shedding when the Reynolds number is between 210 and 270, and unsteady three-dimensional flow with vortex shedding when the Reynolds number is above 270. Results from three-dimensional simulation are compared with the corresponding axisymmetric simulations for Re>210 in order to see the effect of unsteadiness and three-dimensionality on heat transfer past a sphere. The local Nusselt number distribution obtained from the 3D simulation shows big differences in the wake region compared with axisymmetric one, when there exists strong vortex shedding in the wake. But the differences in surface-average Nusselt number between axisymmetric and three-dimensional simulations are small owing to the smaller surface area associated with the base region. The shedding process is observed to be dominantly one-sided and as a result axisymmetry of the surface heat transfer is broken even after a time-average. The one-sided shedding also results in a time-averaged mean lift force on the sphere.

Numerical Investigation on Turbulence Statistics and Heat Transfer of a Circular Jet Impinging on a Roughened Flat Plate

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Abdulrahman Alenezi ◽  
Abdulrahman Almutairi ◽  
Hamad Alhajeri ◽  
Abdulaziz Gamil ◽  
Faisal Alshammari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Roughness Element ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Target Plate ◽  
Cross Sectional ◽  
Flow Physics ◽  
Baseline Case

Abstract A detailed heat transfer numerical study of a three-dimensional impinging jet on a roughened isothermal surface is presented and is investigated from flow physics vantage point under the influence of different parameters. The effects of the Reynolds number, roughness location, and roughness dimension on the flow physics and heat transfer parameters are studied. Additionally, the relations between average heat transfer coefficient (AHTC) and flow physics including pressure, wall shear and flow vortices with thermodynamic nonequilibrium are offered. This paper studies the effect of varying both location and dimension of the roughness element which took the shape of square cross-sectional continuous ribs to deliver a favorable trade-off between total pressure loss and heat transfer rate. The roughness element was tested for three different radial locations (R/D) = 1, 1.5, and 2 and at each location its height (i.e., width) (e) was changed from 0.25 to 1 mm in incremental steps of 0.25. The study used a jet angle (α) of 90 deg, jet-to-target distance (H/D = 6), and Re ranges from 10,000 to 50,000, where H is the vertical distance between the target plate and jet exit. The results show that the AHTC can be significantly affected by changing the geometry and dimensions of the roughness element. This variation can be either an augmentation of, or decrease in, the (HTC) when compared with the baseline case. An enhancement of 12.9% in the AHTC was achieved by using optimal location and dimensions of the roughness element at specific Reynolds number. However, a diminution between 10% and 30% in (AHTC) was attained by the use of rib height e = 1 mm at Re = 50k. The variation of both rib location and height showed better contribution in increasing heat transfer for low-range Reynolds numbers.

LES Investigation of Flow and Heat Transfer in a Channel With Dimples and Protrusions

2007 ◽  
Author(s):  
Mohammad A. Elyyan ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Reynolds Numbers ◽  
The Other ◽  
Secondary Effect ◽  
Flow Acceleration ◽  
Heat Transfer Augmentation ◽  
Flow And Heat Transfer ◽  
Separated Shear Layer ◽  
Dimple Surface

LES calculations are conducted for flow in a channel with dimples and protrusions on opposite walls with both surfaces heated at three Reynolds numbers, ReH = 220, 940, and 9300 ranging from laminar, weakly turbulent to fully turbulent, respectively. Turbulence generated by the separated shear layer in the dimple and along the downstream rim of the dimple is primarily responsible for heat transfer augmentation on the dimple surface. On the other hand, augmentation on the protrusion surface is mostly driven by flow impingement and flow acceleration between protrusions, while the turbulence generated in the wake has a secondary effect. Heat transfer augmentation ratios of 0.99 at ReH = 220, 2.9 at ReH = 940, and 2.5 at ReH = 9300 are obtained. Both skin friction and form losses contribute to pressure drop in the channel, with form losses increasing from 45% to 80% with an increase in the Reynolds number. Friction coefficient augmentation ratios of 1.67, 4.82 and 6.37 are obtained at ReH = 220, 940, and 9300, respectively. Based on the geometry studied, it is found that dimples and protrusions may not be viable heat transfer augmentation surfaces when the flow is steady and laminar.

Computation of Flow and Heat Transfer in Rotating Rectangular Channels (AR=4:1) With Pin-Fins by a Reynolds Stress Turbulence Model

2006 ◽  
Vol 129 (6) ◽  
pp. 685-696 ◽  
Author(s):  
Guoguang Su ◽  
Hamn-Ching Chen ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Rotation Number ◽  
Rectangular Channel ◽  
Density Ratio ◽  
Three Dimensional ◽  
Diameter Ratio ◽  
Mean Velocity ◽  
Flow And Heat Transfer ◽  
Pin Fins

Computations with multi-block chimera grids were performed to study the three-dimensional turbulent flow and heat transfer in a rotating rectangular channel with staggered arrays of pin-fins. The channel aspect ratio (AR) is 4:1, the pin length to diameter ratio (H∕D) is 2.0, and the pin spacing to diameter ratio is 2.0 in both the stream-wise (S1∕D) and span-wise (S2∕D) directions. A total of six calculations have been performed with various combinations of rotation number, Reynolds number, and coolant-to-wall density ratio. The rotation number and inlet coolant-to-wall density ratio varied from 0.0 to 0.28 and from 0.122 to 0.20, respectively, while the Reynolds number varied from 10,000 to 100,000. For the rotating cases, the rectangular channel was oriented at 150deg with respect to the plane of rotation to be consistent with the configuration of the gas turbine blade. A Reynolds-averaged Navier-Stokes (RANS) method was employed in conjunction with a near-wall second-moment turbulence closure for detailed predictions of mean velocity, mean temperature, and heat transfer coefficient distributions.

Periodic Fluid Flow and Heat Transfer in a Square Cavity Due to an Insulated or Isothermal Rotating Cylinder

2009 ◽  
Vol 131 (11) ◽  
Author(s):  
Y.-C. Shih ◽  
J. M. Khodadadi ◽  
K.-H. Weng ◽  
A. Ahmed
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convection Heat Transfer ◽  
Reynolds Numbers ◽  
Rotating Cylinder ◽  
Flow Fields ◽  
Square Cavity ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Rotating Objects

The periodic state of laminar flow and heat transfer due to an insulated or isothermal rotating cylinder object in a square cavity is investigated computationally. A finite-volume-based computational methodology utilizing primitive variables is used. Various rotating objects (circle, square, and equilateral triangle) with different sizes are placed in the middle of a square cavity. A combination of a fixed computational grid and a sliding mesh was utilized for the square and triangle shapes. For the insulated and isothermal objects, the cavity is maintained as differentially heated and isothermal enclosures, respectively. Natural convection heat transfer is neglected. For a given shape of the object and a constant angular velocity, a range of rotating Reynolds numbers are covered for a Pr=5 fluid. The Reynolds numbers were selected so that the flow fields are not generally affected by the Taylor instabilities (Ta<1750). The periodic flow field, the interaction of the rotating objects with the recirculating vortices at the four corners, and the periodic channeling effect of the traversing vertices are clearly elucidated. The simulations of the dynamic flow fields were confirmed against experimental data obtained by particle image velocimetry. The corresponding thermal fields in relation to the evolving flow patterns and the skewness of the temperature contours in comparison to the conduction-only case were discussed. The skewness is observed to become more marked as the Reynolds number is lowered. Transient variations of the average Nusselt numbers of the respective systems show that for high Re numbers, a quasiperiodic behavior due to the onset of the Taylor instabilities is dominant, whereas for low Re numbers, periodicity of the system is clearly observed. Time-integrated average Nusselt numbers of the insulated and isothermal object systems were correlated with the rotational Reynolds number and shape of the object. For high Re numbers, the performance of the system is independent of the shape of the object. On the other hand, with lowering of the hydraulic diameter (i.e., bigger objects), the triangle and the circle exhibit the highest and lowest heat transfers, respectively. High intensity of the periodic channeling and not its frequency is identified as the cause of the observed enhancement.

Thermal-Hydraulic Performance of SiC-Water and Al2O3-Water Nanofluids in the Minichannel

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Ji Zhang ◽  
Yanhua Diao ◽  
Yaohua Zhao ◽  
Yanni Zhang
Keyword(s):  
Heat Transfer ◽  
Single Phase ◽  
Volume Concentration ◽  
Working Fluid ◽  
Al2o3 Nanoparticles ◽  
Particle Sizes ◽  
Enhance Heat Transfer ◽  
Flow And Heat Transfer ◽  
Effective Particle Size ◽  
Effective Particle

The single-phase flow and heat transfer behaviors of SiC and Al2O3 nanoparticles dispersed in water were studied experimentally in a multiport minichannel flat tube (MMFT). The volume concentrations of the two nanofluids ranged from 0.001% to 1%. Their effective particle sizes, thermal conductivities, and viscosities were also measured. Results indicated that these nanofluids as a working fluid could enhance heat transfer but increase pressure drop and the Nusselt number by up to 85%. The two nanofluids exhibited a common optimal volume concentration of 0.01% for heat transfer. Effective particle size was also found to have a significant effect on heat transfer.

Transient Leading to Periodic Fluid Flow and Heat Transfer in a Differentially-Heated Cavity Due to an Insulated Rotating Object

2007 ◽  
Author(s):  
Y.-C. Shih ◽  
J. M. Khodadadi ◽  
K.-H. Weng ◽  
H. F. Oztop
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convection Heat Transfer ◽  
Reynolds Numbers ◽  
High Heat ◽  
Thermal Fields ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
Transient Variations ◽  
Rotating Objects

Computational analysis of transient phenomenon followed by the periodic state of laminar flow and heat transfer due to an insulated rotating object in a square cavity is investigated. A finite-volume-based computational methodology utilizing primitive variables is used. Various rotating objects (circle, square and equilateral triangle) with different sizes are placed in the middle of the cavity. A combination of a fixed computational grid with a sliding mesh was utilized for the square and triangle shapes. The cavity is maintained as a differentially-heated enclosure and the motionless insulated object is set in rotation at time t = 0. Natural convection heat transfer is neglected. For a given shape of the object and a constant angular velocity, a range of rotating Reynolds numbers are covered for a Pr = 5 fluid. The Reynolds numbers were selected so that the flow fields are not generally affected by the Taylor instabilities (Ta &lt; 1750). The evolving flow field and the interaction of the rotating objects with the recirculating vortices at the four corners are elucidated. The corresponding thermal fields in relation to the evolving flow patterns and the skewness of the temperature contours in comparison to conduction-only case were discussed. The skewness is observed to become more marked as the Reynolds number is lowered. At the same time, similarity of the thermal fields for various shapes for the same Reynolds number varifies the appropriate selection of the hydraulic diameter. Transient variations of the average Nusselt numbers on the two walls show that for high Re numbers, a quasi-periodic behavior due to the onset of the Taylor instabilities is dominant, whereas for low Re numbers, periodicity of the system is clearly observed. Time-integrated average Nusselt number of the cavity is correlated to the rotational Reynolds number and shape of the object. The triangle object clearly gives rise to high heat transfer followed by the square and circle objects.

Numerical Study of Flow and Heat Transfer Characteristics of Impinging Jets

2010 ◽  
Author(s):  
Tarek M. Abdel-Salam
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Numerical Study ◽  
Three Dimensional ◽  
Impinging Jets ◽  
Two Dimensional ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

This study presents results for flow and heat transfer characteristics of two-dimensional rectangular impinging jets and three-dimensional circular impinging jets. Flow geometries under consideration are single and multiple impinging jets issued from a plane wall. Both confined and unconfined configurations are simulated. Effects of Reynolds number and the distance between the jets are investigated. Results are obtained with a finite volume computational fluid dynamics (CFD) code. Structured grids are used in all cases of the present study. Turbulence is treated with a two equation k-ε model. Different jet velocities have been examined corresponding to Reynolds numbers of 5,000 to 20,000. Results of the three-dimensional cases show that Reynolds number has no effect on the velocity distribution of the center jet. Results of both two-dimensional and three-dimensional cases show that Reynolds number highly affects the heat transfer and values of the Nusselt number. The maximum Nusselt number was always found at the stagnation point of the center jet.

Sign in / Sign up

Export Citation Format

Share Document