scholarly journals Heat transfer in a novel microwave heating device coupled with atomization feeding

2021 ◽  
pp. 288-288
Author(s):  
Shangzhi Yu ◽  
Qinglong Xie ◽  
Xiaoning Mao ◽  
Ying Duan ◽  
Yong Nie
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
High Temperature ◽  
Microwave Heating ◽  
Flow Rate ◽  
Orifice Diameter ◽  
Spray Parameters ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Spray Flow Rate

The heat transfer characteristics of the microwave heating coupled with atomization feeding were investigated using ethanol as the spray medium on a pressure swirl nozzle. The effects of spray height, flow rate and temperature on the sauter mean diameter (SMD) of atomized droplets were examined. The results showed that the droplet SMD was 12-130 ?m, which increased with the spray height and decreased with the flow rate and temperature of spray medium. Through the fitting of the experimental data, the dimensionless correlation of the droplet SMD which was based on orifice diameter, Reynolds and Ohnesorge numbers was obtained. The calculated results were basically consistent with the experimental data within 15% error. The heat transfer characteristics of atomized droplets on high-temperature surface of SiC bed heated by microwave were then investigated. The effects of spray flow rate, spray height and spray temperature on the heat transfer characteristics were examined. The power of spray heat transfer decreased with the temperature and increased with the spray flow rate and spray height. The dimensionless correlation to describe the heat transfer characteristics of atomized droplets on the high-temperature SiC surface under the microwave heating was obtained which included thermophysical properties of spray medium, spray parameters, and temperatures of the high-temperature bed surface and spray medium, with the error of ?20%. These correlations can be used to predict the SMD of the atomized droplets and the power of spray heat transfer in the microwave heating process.

scholarly journals Numerical Investigation on the Influence of Surface Flow Direction on the Heat Transfer Characteristics in a Granite Single Fracture

2021 ◽  
Vol 11 (2) ◽  
pp. 751
Author(s):  
Xuefeng Gao ◽  
Yanjun Zhang ◽  
Zhongjun Hu ◽  
Yibin Huang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Flow Rate ◽  
Flow Direction ◽  
Heat Extraction ◽  
Geothermal System ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Heat Transfer Capacity

As fluid passes through the fracture of an enhanced geothermal system, the flow direction exhibits distinct angular relationships with the geometric profile of the rough fracture. This will inevitably affect the heat transfer characteristics in the fracture. Therefore, we established a hydro-thermal coupling model to study the influence of the fluid flow direction on the heat transfer characteristics of granite single fractures and the accuracy of the numerical model was verified by experiments. Results demonstrate a strong correlation between the distribution of the local heat transfer coefficient and the fracture morphology. A change in the flow direction is likely to alter the transfer coefficient value and does not affect the distribution characteristics along the flow path. Increasing injection flow rate has an enhanced effect. Although the heat transfer capacity in the fractured increases with the flow rate, a sharp decline in the heat extraction rate and the total heat transfer coefficient is also observed. Furthermore, the model with the smooth fracture surface in the flow direction exhibits a higher heat transfer capacity compared to that of the fracture model with varying roughness. This is attributed to the presence of fluid deflection and dominant channels.

Numerical Analysis of Heat Transfer Characteristics in Microwave Heating of Magnetic Dielectrics

2011 ◽  
Vol 43 (3) ◽  
pp. 1070-1078 ◽  
Author(s):  
Zhiwei Peng ◽  
Jiann-Yang Hwang ◽  
Chong-Lyuck Park ◽  
Byoung-Gon Kim ◽  
Gerald Onyedika
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Microwave Heating ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Numerical Investigation of Heat Transfer Characteristics of Different Nanoparticles Using Modified Eulerian-Eulerian Model

2020 ◽  
Author(s):  
Muzafar Hussain ◽  
Shahbaz Tahir
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Exchangers ◽  
Single Phase ◽  
Reynolds Numbers ◽  
Operating Conditions ◽  
Phase Model ◽  
Heat Transfer Characteristics ◽  
Eulerian Model ◽  
Transfer Characteristics

Abstract Nanofluids are widely adopted nowadays to enhance the heat transfer characteristics in the solar applications because of their excellent thermophysical properties. In this paper, a modified Eulerian-Eulerian model recently developed based on experiments was validated numerically to account for the deviations from the experimental data. The modified Eulerian-Eulerian model is compared with the single-phase model, Eulerian-Eulerian models for TiO2-water at different operating conditions and deviation from the experimental data for each of the model was documented. However, the modified Eulerian-Eulerian model gave much closer results when compared to the experimental data. For the further extension of work, the modified Eulerian-Eulerian model was applied to different nanofluids in order to investigate their heat transfer characteristics. Three different nanoparticles were investigated namely Cu, MgO, and Ag and their heat transfer characteristics is calculated based on the modified Eulerian-Eulerian model as well as the single-phase model for the comparison. For lower values of Reynolds numbers, the average heat transfer coefficient was almost identical for both models with small percentage of error but for higher Reynolds numbers, the deviation got larger. Therefore, single-phase model is not appropriate for higher Reynolds numbers and modified Eulerian-Eulerian model should be used to accurately predict the heat transfer characteristics of the nanofluids at higher Reynolds numbers. From the analysis it is found that the Ag-water nanofluid have the highest heat transfer characteristics among others and can be employed in the solar heat exchangers to enhance the heat transfer characteristics and to further improve the efficiency.

Effect of Turbulent Intensity and Axial Gap on Turbine Heat Transfer Using Steady and Harmonic Models

2013 ◽  
Author(s):  
Sridhar Murari ◽  
Sunnam Sathish ◽  
Ramakumar Bommisetty ◽  
Jong S. Liu
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Flow Field ◽  
Turbulence Intensity ◽  
Pressure Coefficient ◽  
Heat Transfer Characteristics ◽  
Complex Flow ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Heat Loads

The knowledge of heat loads on the turbine is of great interest to turbine designers. Turbulence intensity and stator-rotor axial gap plays a key role in affecting the heat loads. Flow field and associated heat transfer characteristics in turbines are complex and unsteady. Computational fluid dynamics (CFD) has emerged as a powerful tool for analyzing these complex flow systems. Honeywell has been exploring the use of CFD tools for analysis of flow and heat transfer characteristics of various gas turbine components. The current study has two objectives. The first objective aims at development of CFD methodology by validation. The commercially available CFD code Fine/Turbo is used to validate the predicted results against the benchmark experimental data. Predicted results of pressure coefficient and Stanton number distributions are compared with available experimental data of Dring et al. [1]. The second objective is to investigate the influence of turbulence (0.5% and 10% Tu) and axial gaps (15% and 65% of axial chord) on flow and heat transfer characteristics. Simulations are carried out using both steady state and harmonic models. Turbulence intensity has shown a strong influence on turbine blade heat transfer near the stagnation region, transition and when the turbulent boundary layer is presented. Results show that a mixing plane is not able to capture the flow unsteady features for a small axial gap. Relatively close agreement is obtained with the harmonic model in these situations. Contours of pressure and temperature on the blade surface are presented to understand the behavior of the flow field across the interface.

Sign in / Sign up

Export Citation Format

Share Document