scholarly journals Effect of Heat Treatment on the Microstructure and Mechanical Properties of High-Strength Ti–6Al–4V–5Fe Alloy

2019 ◽  
Vol 60 (2) ◽  
pp. 269-276
Author(s):  
Zhenyu Wang ◽  
Libin Liu ◽  
Ligang Zhang ◽  
Jinwen Sheng ◽  
Di Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Microstructure And Mechanical Properties

Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15 Titanium Alloy

2021 ◽  
Vol 1016 ◽  
pp. 906-910
Author(s):  
Xin Hua Min ◽  
Cheng Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
High Strength ◽  
Slow Cooling ◽  
Microstructure And Mechanical Properties ◽  
Ta15 Titanium Alloy ◽  
The Ideal

In this paper,effect of the different forging processes on the microstructure and mechanical properties of the flat flat billets of TA15 titanium alloy was investigated.The flat billiets of 80 mm×150 mm×L sizes of TA15 titanium alloy are produced by four different forging processes.Then the different microstrure and properties of the flat billiets were obtained by heat treatment of 800 °C~850 °C×1 h~4h.The results show that, adopting the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling, the primary αphases content is just 10%, and there are lots of thin aciculate phases on the base. This microstructure has both high strength at room temperature and high temperature, while the properties between the cross and lengthwise directions are just the same. So the hot processing of the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling is choosed as the ideal processing for production of aircraft frame parts.

Microstructure and Mechanical Properties of a Nb-Microalloyed Medium Carbon Steel Treated by Quenching-Partitioning Process

2012 ◽  
Vol 531-532 ◽  
pp. 596-599
Author(s):  
Kai Zhang ◽  
Shang Wen Lu ◽  
Yao Hui Ou ◽  
Xiao Dong Wang ◽  
Ning Zhong
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Electron Microscope ◽  
Carbon Steel ◽  
Retained Austenite ◽  
High Strength ◽  
Medium Carbon Steel ◽  
Orientation Relationships ◽  
Medium Carbon ◽  
Microstructure And Mechanical Properties

The recently developed “quenching and partitioning” heat treatment and “quenching-partitioning-tempering” heat treatment are novel processing technologies, which are designed for achieving advanced high strength steels (AHSS) with combination of high strength and adequate ductility. In present study, a medium carbon steel containing Nb was subjected to the Q-P-T process, and both the microstructure and mechanical properties was studied. The experimental results show that the Nb-microalloyed steel demonstrates high tensile strength and relatively high elongation. The microstructure of the steel was investigated in terms of scanning electron microscope and transmission electron microscope, and the results indicate that the Q-P-T steel consist of fine martensite laths with dispersive carbide precipitates and the film-like interlath retained austenite. The orientation relationships between martensite and retained austenite is as well-known Kurdjurmov-Sachs relationship and Nishiyama-Wasserman relationship.

Effect of Different Heat Treatments on Microstructure and Mechanical Properties of the Martensitic Gx12CrMoVNbN9-1 Cast Steel / Wpływ Parametrów Obróbki Cieplnej Na Mikrostrukture I Własciwosci Mechaniczne Martenzytycznego Staliwa Gx12CrMoVNbn9-1

2013 ◽  
Vol 58 (1) ◽  
pp. 25-30 ◽  
Author(s):  
G. Golanski ◽  
J. Słania
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Impact Energy ◽  
Cast Steel ◽  
Lath Martensite ◽  
High Strength ◽  
Strength Properties ◽  
Microstructure And Mechanical Properties ◽  
Quenching And Tempering ◽  
Very High

The paper presents a research on the influence of multistage heat treatment with the assumed parameters of temperature and time on the microstructure and mechanical properties of high-chromium martensitic GX12CrMoVNbN9-1 (GP91) cast steel. In the as-cast state GP91 cast steel was characterized by a microstructure of lath martensite with numerous precipitations of carbides of the M23C6, M3C and NbC type, with its properties higher than the required minimum. Hardening of the examined cast steel contributes to obtaining a microstructure of partly auto-tempered martensite of very high strength properties and impact strength KV on the level of 9-15 J. Quenching and tempering with subsequent stress relief annealing of GP91 cast steel contributed to obtaining the microstructure of high-tempered lath martensite with numerous precipitations of the M23C6 and MX type of diverse size. The microstructure of GP91 cast steel received after heat treatment was characterized by strength properties (yield strength, tensile strength) higher than the required minimum and a very high impact energy KV. It has been proved that GP91 cast steel subject to heat treatment No. 2 as a result of two-time heating above the Ac3 temperature is characterized by the highest impact energy.

scholarly journals Effect of Austenization Temperature on the Microstructure in Cr-Mn-Si Steel

2019 ◽  
Vol 9 (2) ◽  
pp. 4942-4945
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Trace Elements ◽  
Polymorphic Transformation ◽  
High Strength ◽  
Heat Treatments ◽  
Thermal Treatments ◽  
Microstructure And Mechanical Properties ◽  
Bainite Structure ◽  
Strength And Plasticity

This work is a part of research on the microstructure and mechanical properties of Cr-Mn-Si steels after various thermal treatments. In order to increase the resistance of the materials against failure it is necessary to possess simultaneously high strength and plasticity at the same time. Normally, in conventional metals, this is impossible. The purpose of the present study is to trace the polymorphic transformation of the microstructure and the redistribution of the trace elements in the corresponding microstructural transformations of the steel at each stage of applied heat treatment - austenization, quenching, austempering, tempering. The chosen sequence of applied heat treatments is to obtain a bainite structure of up to 50% in order to achieve high strength and toughness of the material.

Effect of Heat Treatment on the Properties and Precipitations of High Strength Steel Plate for Construction Machinery

2014 ◽  
Vol 971-973 ◽  
pp. 240-243
Author(s):  
Tao Zhang ◽  
Hua Xing Hou ◽  
Zhao Tan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength Steel ◽  
Steel Plate ◽  
High Strength ◽  
Quenching Temperature ◽  
Tempering Temperature ◽  
Construction Machinery ◽  
Microstructure And Mechanical Properties ◽  
Tempering Resistance

The effect of heat treatment on the microstructure and mechanical properties of High Strength steel plate Q960E for construction machinery was investigated. The result shows the quenching temperature have obvious effects on the mechanical properties, DQ can improve the toughness and the enchance tempering resistance, precipitations become more and bigger with the rise of the tempering temperature.

scholarly journals Characterization of the Role of Squeeze Casting on the Microstructure and Mechanical Properties of the T6 Heat Treated 2017A Aluminum Alloy

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
S. Souissi ◽  
N. Souissi ◽  
H. Barhoumi ◽  
M. ben Amar ◽  
C. Bradai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Squeeze Casting ◽  
Applied Pressure ◽  
High Strength ◽  
Casting Process ◽  
Tensile Tests ◽  
Scanning Calorimetry ◽  
Microstructure And Mechanical Properties

In this study, the effects of squeeze casting process and T6 heat treatment on the microstructure and mechanical properties of 2017A aluminum alloy were investigated with scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDS), differential scanning calorimetry (DSC), and microhardness and tensile tests. The results showed that this alloy contained α matrix, θ-Al2Cu, and other phases. Furthermore, the applied pressure and heat treatment refines the microstructure and improve the ultimate tensile strength (UTS) to 296 MPa and the microhardness to 106 HV with the pressure 90 MPa after ageing at 180°C for 6 h. With ageing temperature increasing to 320°C for 6 h, the strength of the alloy declines slightly to 27 MPa. Then, the yield strength drops quickly when temperature reaches over 320°C. The high strength of the alloy in peak-aged condition is caused by a considerable amount of θ′ precipitates. The growth of θ′ precipitates and the generation of θ phase lead to a rapid drop of the strength when temperature is over 180°C.

Sign in / Sign up

Export Citation Format

Share Document