Effect of Operator Experience on the Outcome of Fiber Post Cementation With Different Resin Cements

2013 ◽  
Vol 38 (5) ◽  
pp. 555-564 ◽  
Author(s):  
GM Gomes ◽  
OMM Gomes ◽  
A Reis ◽  
JC Gomes ◽  
AD Loguercio ◽  
...  
Keyword(s):  
Bond Strength ◽  
In Vitro Study ◽  
T Test ◽  
Fiber Post ◽  
Operator Experience ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Adhesive Cement ◽  
Push Out

SUMMARY Objectives To evaluate the influence of operator experience (dentist vs student) and cementation system (Adper Scotchbond Multi-Purpose [SBMP] + RelyX ARC [1]; Adper Single Bond 2 [SB] + RelyX ARC [2] and RelyX U100 [3]) on the push-out bond strength (BS) of fiber post to radicular dentin. Materials and Methods The roots of 48 extracted human maxillary central incisors were prepared and divided into six groups (n=8), according to combination of the above factors. Glass fiber posts were cemented in accordance with the instructions of the manufacturer of each cementation system. After water storage at 37°C for one week, the roots were cross-sectioned into six 1-mm thick slices and the push-out test was performed (0.5 mm/min). Data were statistically analyzed by two-way analysis of variance and Tukey tests (α=0.05). The BS results obtained by dentist and student for each cementation system were compared using the Student t-test (α=0.05). Results Higher BS means were observed for the expert operators, irrespective of the cementation system used (p=0.006). RelyX U100 showed the highest bond strength, but it did not differ from SBMP + RelyX ARC. The Student t-test revealed that only RelyX U100 was not affected by the operator's experience. Conclusion Within the limitations of this in vitro study, it can be concluded that the self-adhesive cement RelyX U100 showed the highest bond strength to the root canal in the student's group, and its performance was not affected by the operator's experience.

scholarly journals Choice of Endodontic Fiber Posts and its Influence on Dental Malpractice: An in vitro Evaluation

2017 ◽  
Vol 18 (6) ◽  
pp. 452-457
Author(s):  
Houssam Jassar ◽  
Hassan El Husseini
Keyword(s):  
Bond Strength ◽  
Low Cost ◽  
Fiber Post ◽  
Endodontically Treated Teeth ◽  
Fiber Posts ◽  
Significant Difference ◽  
Post Space ◽  
Adhesive Cement ◽  
Push Out

ABSTRACT Aims and objectives The fiber post type used in restoring endodontically treated teeth may affect the dental expert decision in the case of dental malpractice. The aim of this study was to evaluate the low-cost commercial fiber post in comparison with a higher cost or well-known documented fiber post system. Materials and methods A total of 20 premolars were selected for the study; following endodontic treatment, specimens were randomly divided into two groups of 10 specimens each according to the type of fiber post used: (1) Low-cost commercial fiber post (OYAPost, Taper Lucent, OYARICOM) and (2) higher cost well-known fiber post (Rely X Fiber post, 3M ESPE). Both fiber posts were cemented using self-adhesive cement (Rely X Unicem). Samples were subjected to push-out bond strength and to failure analysis. One-way analysis of variance was used (p < 0.005). Results There was no significant difference between the bond strength of the two tested groups (p > 0.05), while statistically significant difference (p < 0.05) was noted between the different post space regions (cervical, middle, and apical). Conclusion Based on the evidence from the study, it can be concluded that the type of fiber post should not affect the dental expert decision in the case of dental malpractice/lawsuit. Clinical significance All types of low-cost fiber posts may behave similarly to other higher cost or well-documented fiber posts. How to cite this article Ayoub F, Jassar H, El Husseini H, Salameh Z. Choice of Endodontic Fiber Posts and its Influence on Dental Malpractice: An in vitro Evaluation. J Contemp Dent Pract 2017;18(6):452-457.

CAD/CAM Milled Glass Fiber Posts: Adaptation and Mechanical Behavior in Flared Root Canals

2021 ◽  
Author(s):  
MER Gama ◽  
GS Balbinot ◽  
GC Ferreira ◽  
EG Mota ◽  
VCB Leitune ◽  
...  
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Fiber Post ◽  
Root Canals ◽  
Fiber Posts ◽  
Cad Cam ◽  
Glass Fiber Posts ◽  
Glass Fiber Post ◽  
Post And Core ◽  
Push Out

SUMMARY This study aimed to evaluate the cementation and mechanical behavior of flared root canals restored with CAD/CAM milled glass fiber post-and-core systems. Sixty-six endodontically treated human canines with a flared root canal were divided into three different groups according to the type of post: GPF received prefabricated posts; GREL received relined glass fiber posts, and GMILLED received CAD/CAM milled glass fiber posts. Cementation was performed with self-adhesive resin cement. The samples were submitted to x-ray microcomputed tomography analysis for the analysis of voids and gaps. The roots were sectioned and submitted to the push-out bond strength test. The load-to-fracture was evaluated in post-and-core systems. GMILLED presented lower void and lower gap volumes when compared to GPF and GREL. On the load-to-fracture test, GREL presented statistically significant higher values than GMILLED. GPF values had no statistically significant difference from the two other groups. On the push-out bond strength test, GPF presented statistically significant lower values when compared to GREL and GMILLED. The most common failure pattern was between dentin and cement in all groups. CAD/CAM milled glass fiber post-and-core systems presented an enhanced adaptation of glass fiber posts to flared root canal systems. Their results were comparable to relined posts in bond strength, while load-to-fracture-results for GMILLED were lower than those for GPF.

scholarly journals Influence of the Cement Film Thickness on the Push-Out Bond Strength of Glass Fiber Posts Cemented in Human Root Canals

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Natália Araújo Silva Prado ◽  
Reinaldo de Souza Ferreira ◽  
Marcos Henrique de Pinho Maurício ◽  
Sidnei Paciornik ◽  
Mauro Sayão de Miranda
Keyword(s):  
Bond Strength ◽  
Film Thickness ◽  
Glass Fiber ◽  
Shear Bond Strength ◽  
Root Canals ◽  
Fiber Posts ◽  
Before And After ◽  
Glass Fiber Posts ◽  
Adhesive Cement ◽  
Push Out

The present study evaluated the influence of the cement film thickness on the push-out bond strength of glass fiber posts in the cervical, medium, and apical thirds of root canal spaces. Thirty roots were randomly divided into three groups, according to the fiber post system’s drills: (G1) #2; (G2) #3; (G3) #4. The posts were cemented using a self-adhesive cement, and a small amount of powdered Rhodamine B was used as a stain. Images of both sides of each slice were obtained before and after the push-out test. To determine the cement thickness, a macro routine was developed using the software KS 400. The data were analyzed statistically using Kruskal-Wallis and Dunn’s test. G2 (14.62±5.15 MPa) showed statistically higher bond strength values than G1 (10.04±5.13 MPa) and G3 (7.68±6.14 MPa). All groups presented higher bond strength values in the apical third. The bur diameter significantly influenced the results of the shear bond strength for the push-out test. The slight increase in the cement thickness allowed an increase in the values of shear bond strength when compared to very thin or very thick cement films.

scholarly journals Influence of Relining Post on the Bond Strength of Resin Cements

2015 ◽  
Vol 16 (7) ◽  
pp. 559-564 ◽  
Author(s):  
Matheus Coelho Bandéca ◽  
Adriano Augusto Melo de Mendonça ◽  
Etevaldo Matos Maia Filho ◽  
Fausto da Silva Bramante ◽  
Darlon Martins Lima ◽  
...  
Keyword(s):  
Bond Strength ◽  
Resin Cement ◽  
The Self ◽  
Fiber Post ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Fiber Posts ◽  
Significant Difference ◽  
Adhesive Cement ◽  
Push Out

ABSTRACT This study evaluated the influence of relining fiber posts on the bond strength (BS) of resin cements in the root canal. Forty bovine teeth were divided in four groups (n = 10)G1 (ARC)—fiber post cemented with resin cement RelyX ARC; G2 (ARC+Z350)—relined fiber post cemented with RelyX ARC; G3 (U200)—fiber post cemented with self-adhesive cement RelyX U200; G4 (U200+Z350)—relined fiber post cemented with RelyX U200. The roots were sectioned in six 1.2-mm slices and the push-out test was performed. Data were analyzed by three-way analysis of variance (ANOVA), and Tukey's test (α = 0.05). For the conventional resin cement, there was no significant difference between groups G1-ARC (15.5 ± 3.8) and G2-ARC+Z350 (16.1 ± 4.5). For the self-adhesive cement, the results revealed higher BS values for relined posts G4-U200 + Z350 (19.9 ± 7.9) as compared to non-relined posts G3-U200 (14.4 ± 4.5). For both cements, in groups of relined posts, the apical and the cervical thirds presented similar BS. Relining enhances the performance of the self-adhesive resin cement, and the interaction between relining and root third influences the BS to the conventional resin cement. How to cite this article Conde DM, Rodrigues VP, de Fátima Carvalho Souza S, Bauer JRO, da Silva Bramante F, Lima SNL, Filho EMM, Bandeca MC, de Mendonça AAM, Lima DM. Influence of Relining Post on the Bond Strength of Resin Cements. J Contemp Dent Pract 2015;16(7):559-564.

scholarly journals Push-out bond strength of glass fiber posts luted with two resin cements

2017 ◽  
Vol 20 (4) ◽  
pp. 78
Author(s):  
Blanca Liliana Torres Léon ◽  
Vitor Lopes Franco ◽  
Emily Vivianne Freitas Silva ◽  
Leonardo Muniz ◽  
Fernando Carneiro Ribeiro
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Fiber Post ◽  
Resin Cements ◽  
Anterior Teeth ◽  
Fiber Posts ◽  
Post And Core Technique ◽  
Glass Fiber Posts ◽  
Glass Fiber Post ◽  
Push Out

<p class="CorpoA"><strong>Objective.</strong> To evaluate the bond strength of a prefabricated glass fiber post to the root dentin with two resin cements using the push-out test. <strong>Material and Methods.</strong> Thirty fiber posts (White Post ECD) were cemented in human endodontically treated anterior teeth with two resin cements (n=15): Relyx<sup>TM </sup>ARC and AllCem. The roots were transversely sectioned and divided in cervical, middle and apical thirds after 48 h of cementation. The specimens' retention was tested by push-out method. The results were analyzed by 2-way ANOVA and Tukey’s test (<em>p</em>&lt;0.05). <strong>Results.</strong> There were no significant differences in the bond strength between the resin cements. The bond strength was higher in cervical third than in middle and apical thirds for both resin cements. It was observed higher percentages of adhesive failures followed by mixed. <strong>Conclusions.</strong> Both resin cements are indicated in the cementation of glass fiber post.</p><p class="CorpoA"><strong>Keywords</strong></p><p class="CorpoA">Dental prosthesis; Post and core technique; Biomechanical phenomena.</p>

scholarly journals Influence of Er,Cr:YSGG Laser Irradiation on the Push-Out Bond Strength of Zirconia and Glass Fiber Posts with Radicular Dentin

2019 ◽  
Vol 2019 ◽  
pp. 1-5
Author(s):  
Raneem S. Alofi ◽  
Ibraheem F. Alshiddi ◽  
Yasser F. AlFawaz ◽  
Abdulaziz Alsahhaf ◽  
Khulud Abdulrahman Al-Aali ◽  
...  
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Testing Machine ◽  
Resin Cement ◽  
Cervical Region ◽  
Fiber Posts ◽  
Significant Difference ◽  
Glass Fiber Posts ◽  
Push Out

Objective. This in vitro study was designed to evaluate the influence of an Er,Cr:YSGG laser on the bond strength of zirconia and glass fiber posts with root dentin. Materials and methods. Ninety extracted single-rooted human teeth were randomized into 6 groups (n = 15/group) on the basis of different posts (zirconia/glass fiber) and Er,Cr:YSGG laser tips (axial and radial). Specimens were prepared for push-out testing with the help of a cutting machine; six slices (2 on each cervical, middle, and apical) of approximately 1 mm thickness were sectioned for all roots on a plane perpendicular to the long axis of the post. All specimens were placed into a universal testing machine with a defined 0.5 mm/min crosshead speed until the maximum failure load was obtained. Results. The highest mean push-out bond strength of the glass fiber and zirconia groups was achieved with laser treatment. The highest push-out bond strength was achieved with the axial fiber tip (7.63 ± 1.22 MPa), and the lowest was achieved with a radial fiber tip of the glass fiber group (6.98 ± 0.96 MPa). ANOVA showed a statistically significant difference between the groups (p=0.041). The mean push-out bond strength was found to be higher with an axial fiber tip for both cervical and apical segments in the glass fiber and zirconia groups (p<0.05). The independent t-test resulted in the overall highest mean push-out bond strength in the apical segments (p=0.026). Conclusion. Within the limits of the present in vitro research study, an enhancement in the push-out bond strength of resin cement, mainly in the cervical region of the root canal, was achieved after irradiation with an Er,Cr:YSGG laser using an axial fiber tip.

scholarly journals Effect of Anatomical Customization of the Fiber Post on the Bond Strength of a Self-Adhesive Resin Cement

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
Adricyla Teixeira Rocha ◽  
Leticia Machado Gonçalves ◽  
Ana Júlia de Carvalho Vasconcelos ◽  
Etevaldo Matos Maia Filho ◽  
Ceci Nunes Carvalho ◽  
...  
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Resin Cement ◽  
Control Group ◽  
Fiber Post ◽  
Adhesive Resin ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Adhesive Resin Cement ◽  
Push Out

Aim. The aim of the study was to evaluate, by means of the push-out test, the effect of the anatomical customization of the fiber post on the bond strength of a self-adhesive resin cement. Methods. Twelve endodontically treated, human, upper central incisors were randomly divided into two groups (n=6): control (glass fiber posts cemented with Relyx® U200) and customized (glass fiber posts anatomically customized with translucent composite resin cemented with Relyx U200). The roots were sectioned into three slices, cervical, middle, and apical, and photographed with a digital camera attached to a stereomicroscopic loupe. The images were analyzed by software, for evaluation of the cement line. The slices were subsequently submitted to the push-out test until the post had completely extruded, and the fracture mode was analyzed with a stereomicroscopic loupe. Results. The results showed significant differences between the groups in the different root thirds in relation to the area occupied by air bubbles (p<0.05). Bond strength, when all the thirds are considered, was 8.77 ± 4.89 MPa for the control group and 16.96 ± 4.85 MPa for the customized group. Conclusion. The customized group showed greater bond resistance than the control group and a more uniform cement layer.

Sign in / Sign up

Export Citation Format

Share Document