Observer-Based Control of Drilling Mode in Rotary Drilling Systems

2021 ◽  
Author(s):  
Maksim V. Faronov ◽  
Ilia G. Polushin
Keyword(s):  
Rotary Drilling

Effect of K-wire Reuse and Drill Mode on Heat Generation in Bone

Hand ◽  
2021 ◽  
pp. 155894472110031
Author(s):  
Muturi G. Muriuki ◽  
Arun K. Reddy ◽  
Alex Tauchen ◽  
Robert M. Havey ◽  
Avinash G. Patwardhan ◽  
...  
Keyword(s):  
Cell Death ◽  
Cortical Bone ◽  
Heat Generation ◽  
Kirschner Wire ◽  
Heat Exposure ◽  
Critical Temperatures ◽  
Rotary Drilling ◽  
External Cooling ◽  
K Wires ◽  
Oscillating Mode

Background We examined the effect of Kirschner wire (K-wire) reuse and use of oscillating mode on heat generation within cortical bone. Methods Two trocar-tipped K-wires were drilled through the diaphysis of each of 30 human metacarpals and phalanges: one K-wire was inserted in rotary mode and another in oscillating mode. Each wire was reused once. Thermocouples placed within the dorsal and volar bone adjacent to the K-wire drill path measured temperatures throughout each test. Results Peak cortex temperatures were 25°C to 164°C. Rotary drilling achieves peak temperatures quicker (31 ± 78 seconds vs 44 ± 78 seconds, P = .19) than oscillating drilling, but insertion time is also less, resulting in lower overall heat exposure. This effect is also seen when the K-wire is reused (34 ± 70 seconds vs 41 ± 85 seconds, P = .4). The length of time that cortical bone was exposed to critical temperatures (47°C or more) was significantly higher when a wire was reused (36 ± 72 seconds vs 43 ± 82 seconds, P = .008). Peak temperatures greater than 70°C (a temperature associated with instantaneous cell death) were observed on many occasions. Conclusions Overall heat exposure may be higher if a K-wire is reused or inserted in oscillating mode. In the absence of external cooling, K-wire insertion into cortical bone can easily expose bone to temperatures that exceed 70°C and may increase the risk of osteonecrosis.

The Forties and Brimmond Fields, Blocks 21/10, 22/6a, UK North Sea

2003 ◽  
Vol 20 (1) ◽  
pp. 557-561 ◽  
Author(s):  
A. Carter ◽  
J. Heale
Keyword(s):  
North Sea ◽  
Low Cost ◽  
New Technology ◽  
Horizontal Wells ◽  
Oil Price ◽  
3D Seismic ◽  
Rotary Drilling ◽  
Geological Society ◽  
Recoverable Reserves ◽  
Infill Drilling

AbstractThis paper updates the earlier account of the Forties Field detailed in Geological Society Memoir 14 (Wills 1991), and gives a brief description of the Brimmond Field, a small Eocene accumulation overlying Forties (Fig. 1).The Forties Field is located 180 km ENE of Aberdeen. It was discovered in 1970 by well 21/10-1 which encountered 119 m of oil bearing Paleocene sands at a depth of 2131 m sub-sea. A five well appraisal programme confirmed the presence of a major discovery including an extension into Block 22/6 to the southeast. Oil-in-place was estimated to be 4600 MMSTB with recoverable reserves of 1800 MM STB. The field was brought onto production in September 1975. Plateau production of 500 MBOD was reached in 1978, declining from 1981 to 77 MBOD in 1999.In September 1992 a programme of infill drilling commenced, which continues today. The earlier infill targets were identified using 3D seismic acquired in 1988. Acquisition of a further 3D survey in 1996 has allowed the infill drilling programme to continue with new seismic imaging of lithology, fluids and saturation changes. The performance of the 1997 drilling showed that high step-out and new technology wells, including multi-lateral and horizontal wells, did not deliver significantly better targets than drilling in previous years.In line with smaller targets, and in the current oil price environment, low cost technology is being developed through the 1999 drilling programme. Through Tubing Rotary Drilling (TTRD) is currently seen as the most promising way of achieving a step

Evaluation of Belleville Springs and Damping Through Static Cyclic Loading “Hysteresis” for pVARD Optimization: Part-I

2021 ◽  
Author(s):  
Abdelsalam Abugharara ◽  
Stephen Butt
Keyword(s):  
Data Analysis ◽  
Cyclic Loading ◽  
Dynamic Compression ◽  
Range Data ◽  
Compression Tests ◽  
Rotary Drilling ◽  
Static Compression ◽  
Drilling Performance ◽  
Wide Range ◽  
Compression Hysteresis

Abstract One unconventional application that researchers have been investigating for enhancing drilling performance, has been implemented through improving and stabilizing the most effective downhole drilling parameters including (i) increasing downhole dynamic weight on bit (DDWOB), (ii) stabilizing revolution per minutes (rpm), (iii) minimizing destructive downhole vibrations, among many others. As one portion of a three-part-research that consists of a comprehensive data analysis and evaluation of a static compression hysteresis, dynamic compression hysteresis, and corresponding drilling tests, this research investigates through static cyclic loading “Hysteresis” of individual and combined springs and damping the functionality of the passive Vibration Assisted Rotary Drilling (pVARD) tool that could be utilized towards enhancing the drilling performance. Tests are conducted on the two main pVARD tool sections that include (i) Belleville springs, which represent the elasticity portion and (ii) the damping section, which represents the viscous portion. Firstly, tests were conducted through static cyclic loading “Hysteresis” of (i) a mono elastic, (ii) a mono viscus, and (iii) dual elastic-viscus cyclic loading scenarios for the purpose of further examining pVARD functionality. For performing static compression tests, a calibrated geomechanics loading frame was utilized, and various spring stacking of different durometer damping were tested to seek a wide-range data and to provide a multi-angle analysis. Results involved analyzing loading and displacement relationships of individual and combined springs and damping are presented with detailed report of data analysis, discussion, and conclusions.

Sign in / Sign up

Export Citation Format

Share Document