scholarly journals Puncture Impact Test on Glass Plate Fitted with Shatterproof Window Film

2021 ◽  
Vol 70 (11) ◽  
pp. 796-801
Author(s):  
Tomohisa KOJIMA ◽  
Mitsuo NOTOMI ◽  
Tomoaki TSUJI
Keyword(s):  
Impact Test ◽  
Glass Plate ◽  
Window Film

scholarly journals Effective energy applied to a glass plate during an impact test

2019 ◽  
Vol 130 ◽  
pp. 11-18 ◽  
Author(s):  
J.A. Parra ◽  
J. Alonso ◽  
A. Pacios ◽  
M.C. Huerta
Keyword(s):  
Impact Test ◽  
Glass Plate ◽  
Effective Energy

Effects of compression during formation on the microstructure of composite hydroxylapatite/plaster implants for bone reconstruction

1988 ◽  
Vol 46 ◽  
pp. 750-751
Author(s):  
J. Hanker ◽  
K. Cowden ◽  
R. Noecker ◽  
P. Yates ◽  
N. Georgiade ◽  
...  
Keyword(s):  
Cosmetic Surgery ◽  
Glass Plate ◽  
Surgical Reconstruction ◽  
Equal Weight ◽  
Sintered Ceramic ◽  
Setting Times ◽  
Excess Water ◽  
Mixture Prior ◽  
Mechanical Strengths ◽  
Calcium Sulfate Hemihydrate

Composites of plaster of Paris (PP) and hydroxylapatite (HA) particles are being applied for the surgical reconstruction of craniofacial bone defects and for cosmetic surgery. Two types of HA particles are being employed, the dense sintered ceramic (DHA) and the porous, coralline hydroxylapatite (PHA) particles. Excess water is expressed out of the moistened HA/PP mixture prior to implantation and setting by pressing it in a non-tapered syringe against a glass plate. This results in implants with faster setting times and greater mechanical strengths. It was therefore of interest to compare samples of the compressed versus noncompressed mixtures to see whether or not any changes in their microstructure after setting could be related to these different properties.USG Medical Grade Calcium Sulfate Hemihydrate (which has the lowest mortar consistency of any known plaster) was mixed with an equal weight of Interpore 200 particles (a commercial form of PHA). After moistening with a minimum amount of water, disc-shaped noncompressed samples were made by filling small holes (0.339 in. diameter x 0.053 in. deep) in polypropylene molds with a microspatula.

Crack divergence phenomena in tempered glass

2020 ◽  
Vol 13 (3) ◽  
pp. 115-129
Author(s):  
Shin’ichi Aratani
Keyword(s):  
Optimal Design ◽  
High Speed ◽  
Glass Plate ◽  
Acute Angle ◽  
Divergence Angle ◽  
High Speed Photography ◽  
Tempered Glass ◽  
Thick Glass

High speed photography using the Cranz-Schardin camera was performed to study the crack divergence and divergence angle in thermally tempered glass. A tempered 3.5 mm thick glass plate was used as a specimen. It was shown that two types of bifurcation and branching existed as the crack divergence. The divergence angle was smaller than the value calculated from the principle of optimal design and showed an acute angle.

Use of thermomechanical pulp fibers from waste woods for making eco-friendly cushioning material

TAPPI Journal ◽  
2010 ◽  
Vol 9 (7) ◽  
pp. 15-21 ◽  
Author(s):  
JI-YOUNG LEE ◽  
CHUL-HWAN KIM ◽  
JEONG-MIN SEO ◽  
HO-KYUNG CHUNG ◽  
KYUNG-KIL BACK ◽  
...  
Keyword(s):  
Impact Test ◽  
Product Distribution ◽  
Expanded Polystyrene ◽  
Thermomechanical Pulp ◽  
Fiber Structure ◽  
Pulp Fibers ◽  
Cationic Starch ◽  
Thermal Insulating ◽  
Surface Sizing ◽  
The Impact

Eco-friendly cushioning materials were made with thermomechanical pulps (TMPs) from waste woods collected from local mountains in Korea, using a suction-forming method without physical pressing. The TMP cushions had superior shock-absorbing performance, with lower elastic moduli than expanded polystyrene (EPS) or molded pulp. Even though the TMP cushions made using various suction times had many voids in their inner fiber structure, their apparent densities were a little higher than that of EPS and much lower than that of molded pulp. The addition of cationic starch contributed to an increase in the elastic modulus of the TMP cushions without increasing the apparent density, an effect which was different from that of surface sizing with starch. In the impact test, the TMP cushions showed a more ductile pattern than the brittle EPS. The porosity of the TMP cushion was a little less than that of EPS and much greater than that of molded pulp. The porous structure of the TMP cushions contributed to their excellent thermal insulating capacity, which was equivalent to that of EPS. In summary, the TMP packing cushions showed great potential for surviving external impacts during product distribution.

XABO 355

Alloy Digest ◽  
2017 ◽  
Vol 66 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Physical Properties ◽  
Flat Plate ◽  
Structural Steel ◽  
Tensile Properties ◽  
Impact Test ◽  
Steel Grade ◽  
Minimum Yield

Abstract XABO 355 (minimum yield strength of 355 MPa, or 51 ksi, for thicknesses up to 35 mm, or 1.4 in.) is a thermomechanically rolled structural steel. This datasheet applies to thermomechanically rolled flat plate products in thicknesses up to 60 mm (2.4 in.). This steel grade is distinguished by testing by notch-bar impact test to –20 deg C (-4 deg F) minimum. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on forming and joining. Filing Code: SA-777. Producer or source: ThyssenKrupp Steel Europe AG.

Sign in / Sign up

Export Citation Format

Share Document