scholarly journals Flexural Behaviour of a Cold-Formed Steel-Concrete Composite Beam with Channel Type Shear Connector – An Experimental and Analytical Study

2019 ◽  
Vol 29 (3) ◽  
pp. 228-240 ◽  
Author(s):  
Sangeetha Palanivelu
Keyword(s):  
Carrying Capacity ◽  
Composite Beam ◽  
Composite Structures ◽  
Composite Beams ◽  
Load Carrying Capacity ◽  
Shear Connectors ◽  
Finite Element Software ◽  
Load Carrying ◽  
Steel Composite ◽  
Cold Formed Steel

Abstract Steel-concrete composite structures are widely used in the current construction of bridges and multi-storey buildings. The effect of shear connectors in a cold-formed steel-composite beam was studied under flexure. The number of channel connectors in the specimen was varied and the same was compared with a specimen without shear connectors. The performance and failure of cold-formed steel-composite beams were then studied. The presence of shear connectors in the tension zone prevents the formation of cracks which are the major cause of failure in a beam subjected to bending. The load-carrying capacity is greater in a composite beam and an increase in the number of channel connectors from one to five increases the load-carrying capacity by 60 % as compared to a specimen without a connector. A composite beam with five connectors is more ductile, with a ductility factor of 14. The Composite beams were also analysed using the finite element software ANSYS and were found to have good agreement with the experimental results.

scholarly journals Experiments with Externally Prestressed Continuous Composite Girders

10.14311/240 ◽  
2001 ◽  
Vol 41 (3) ◽  
Author(s):  
M. Safan ◽  
A. Kohoutková
Keyword(s):  
Cross Sections ◽  
Carrying Capacity ◽  
Composite Beam ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Cracking Characteristics ◽  
Steel Composite ◽  
Concrete Deck ◽  
Prestressed Beam ◽  
Composite Girders

Steel-concrete composite girders have attractive potentials when applied in bridge construction. The serviceability performance of continuous composite girders is becoming more and more a deterministic parameter in the design of this type of structures. An effective method for improving this performance is to apply prestressing to control or completely eliminate concrete deck cracking caused by static and time dependent actions. Little literature has been found addressing the experimental analysis of continuous girders prestressed by means of external deviated tendons. The current research aims to investigate the behavior of a double-span steel composite beam externally prestressed by means of continuous tendons in terms of cracking characteristics, load deflection response, and load carrying capacity. The efficiency of prestressing is evaluated by comparing the results to those of a non-prestressed beam with similar cross sections and spans.

EXPERIMENTAL INVESTIGATION OF CFRP STRENGTHENED I-SHAPED COLD FORMED STEEL BEAMS

2017 ◽  
Vol 79 (5) ◽  
Author(s):  
Nahushananda Chakravarthy ◽  
Sivakumar Naganathan ◽  
Jonathan Tan Hsien Aun ◽  
Sreedhar Kalavagunta ◽  
Kamal Nasharuddin Mustapha ◽  
...  
Keyword(s):  
Carrying Capacity ◽  
Experimental Results ◽  
Steel Beams ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Length Width ◽  
Cold Formed Steel ◽  
Formed Channel ◽  
Hot Rolled ◽  
Hot Rolled Steel

Cold formed steel differ from hot rolled steel by its lesser thickness and weight. The cold formed steel applicable in roof purlin, pipe racks and wall panels etc. Due its lesser wall thickness the cold formed steel member subjected to buckling. The enhancement of load carrying capacity of the cold formed steel member can be achieved by external strengthening of CFRP. In this study cold formed channel members connected back to back to form I shaped cross section using screws. These built up beam members were 300mm, 400mm and 500mm in length with 100mm screw spacing and edge distance of 50mm were chosen for testing. CFRP fabric cut according to length, width of built up beams and wrapped outer surface of beam using epoxy resin. Experiments were carried out in two sets firstly plain built up beams and secondly CFRP wrapped beams. The test results shows that increased load carrying capacity and reduction in deflection due to CFRP strengthening. Experimental results were compared with AISI standards which are in good agreement. Experimental results shows that CFRP strengthening is economic and reliable.

Experimental investigations on the sandwich composite beams and panels with elastomeric foam core

2017 ◽  
Vol 21 (3) ◽  
pp. 865-894 ◽  
Author(s):  
AR Nazari ◽  
H Hosseini-Toudeshky ◽  
MZ Kabir
Keyword(s):  
Carrying Capacity ◽  
Sandwich Structures ◽  
Failure Mechanisms ◽  
Composite Beams ◽  
Core Material ◽  
Foam Core ◽  
Sandwich Beams ◽  
Load Carrying Capacity ◽  
The Core ◽  
Load Carrying

In this paper, the load-carrying capacity and failure mechanisms of sandwich beams and panels with elastomeric foam core and composite laminate face sheets are investigated. For this purpose, the flexural behavior of laminated composite beams and panels (applied as face sheets) is firstly investigated under three-point bending and central concentrated loads, respectively. Then, the same examination is conducted for the sandwich beams and panels, in which the proposed elastomeric foam is utilized as the core material. It is shown that the failure mechanisms which are associated to the core in the sandwich structures with crushable foams are not considered in the examined sandwich structures. The collapse of the sandwich specimens, examined here, is observed due to the failure of the skins in some steps. By multi-step collapse of these specimens via separately failure of the top and bottom skins, a considerable amount of energy is absorbed between these steps. Due to non-brittle behavior of the core material under loading, a large compression resistance is observed after failure of the top skin which led to the recovery of the load-carrying capacity in the sandwich beams. A similar behavior for the sandwich panels led to the increase of the ultimate strength after appearance of the failure lines on the top skin. The general outcomes of this investigation promise a good influence for the application of elastomeric foam as core material for sandwich structures.

Evaluation of Load Carrying Capacity of the Perforated Shear Connector with Flange Heads

2006 ◽  
Vol 326-328 ◽  
pp. 1811-1816 ◽  
Author(s):  
Young Ho Kim ◽  
Jae Ho Jung ◽  
Soon Jong Yoon ◽  
Won Sup Jang
Keyword(s):  
Carrying Capacity ◽  
Load Transfer ◽  
Shear Capacity ◽  
Load Carrying Capacity ◽  
Shear Connector ◽  
Shear Connectors ◽  
Load Carrying ◽  
Bridge Structures ◽  
Composite Bridge ◽  
New Type

In the construction of composite bridge structures, various types of shear connectors are usually used to provide an efficient load transfer and the composite action of two or more different materials. In the previous work conducted by authors, a new type of the shear connector was introduced, which is the perforated shear connector with flange heads (T-shaped perforated shear connector), and the structural behavior of the shear connector was discussed based on the results of push-out tests. For the practical design of new shear connector, it is necessary to develop the equation for the prediction of the load carrying capacity of the shear connector. In this study, the existing design equations for the Perfobond shear connector were briefly analyzed and the equation for the prediction of the shear capacity of T-shaped perforated shear connector was suggested empirically. By comparing the results obtained by the suggested equation, the existing equations for the Perfobond shear connector, and the experiment, the applicability and effectiveness of the suggested equation was estimated.

Moment redistribution in cold-formed steel sleeved and overlapped two-span purlin systems

2018 ◽  
Vol 21 (16) ◽  
pp. 2534-2552 ◽  
Author(s):  
Pinelopi Kyvelou ◽  
Chi Hui ◽  
Leroy Gardner ◽  
David A Nethercot
Keyword(s):  
Carrying Capacity ◽  
Steel Beams ◽  
Finite Element Models ◽  
Load Carrying Capacity ◽  
Structural Behaviour ◽  
Moment Redistribution ◽  
Load Carrying ◽  
Parametric Studies ◽  
Physical Tests ◽  
Cold Formed Steel

Cold-formed steel purlin systems with overlapped or sleeved connections are alternatives to continuous two-span systems and exhibit different degrees of continuity. Both connection types are highly favourable in practice since they are both strategically placed over an interior support to provide additional moment resistance and rotational capacity where the corresponding demands are at their largest, thus improving the overall structural efficiency. Until recently, full-scale testing has been the most common way of investigating the structural behaviour of such systems. In this study, numerical modelling, capable of capturing the complex contact interactions and instability phenomena, is employed. The developed finite element models are first validated against data from physical tests on cold-formed steel beams featuring sleeved and overlapped connections that have been previously reported in the literature. Following their validation, the models are employed for parametric studies, based on which the structural behaviour of the examined systems is explored, while the applicability of conventional plastic design as well as of a previously proposed design approach is investigated. Finally, the efficiency of these systems in terms of load-carrying capacity is compared with their equivalent continuous two-span systems.

Sign in / Sign up

Export Citation Format

Share Document