scholarly journals The Potential Wind Power Resource in Central-South of the Constanta County

2019 ◽  
Vol 15 (3) ◽  
pp. 1-12
Author(s):  
Emilian Boboc
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Extreme Values ◽  
Reanalysis Data ◽  
Value Theory ◽  
Physical Models ◽  
Structural Safety ◽  
Energy Yield ◽  
Wind Speeds ◽  
Mean Wind Speed

Abstract Usually, wind turbine generator’s structures or radio masts are located in wind exposed sites. The paper aims to investigate the wind conditions in the nearby area of Cobadin Commune, Constanta County, Romania at heights of 150-200m above the surface using global reanalysis data sets CFSR, ERA 5, ERA I and MERRA 2. Using the extreme value theory and the physical models of the datasets, the research focuses on the assessment of the maximum values that are expected for the wind speeds, but the wind statistics created can be used for a further wind or energy yield calculation. Without reaching the survival wind speed for wind turbine generators, with mean wind speed values higher than 7 m/s and considering the cut-in and cut-out wind speeds of 3 m/s, respectively 25 m/s, the site can be exploited in more than 90% of the time to generate electricity, thus, the paper is addressed to the investors in the energy of renewable sources. At the same time, the insights of the wind characteristics and the knowledge of the extreme values of the wind speed can be useful, not just for the designers, in the rational assessment of the structural safety of wind turbines, but also those evaluating the insured losses.

scholarly journals Monitoring and Modeling Roof-Level Wind Speed in a Changing City

Atmosphere ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 87
Author(s):  
Kathrin Baumann-Stanzer ◽  
Sirma Stenzel ◽  
Gabriele Rau ◽  
Martin Piringer ◽  
Felix Feichtinger ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Urban Areas ◽  
Dispersion Model ◽  
Flow Direction ◽  
Energy Yield ◽  
Wind Speeds ◽  
Small Wind Turbine ◽  
Roof Level

Results of an observational campaign and model study are presented demonstrating how the wind field at roof-level in the urban area of Vienna changed due to the construction of a new building nearby. The investigation was designed with a focus on the wind energy yield of a roof-mounted small wind turbine but the findings are also relevant for air dispersion applications. Wind speed profiles above roof top are simulated with the complex fluid dynamics (CFD) model MISKAM (Mikroskaliges Klima- und Ausbreitungsmodell, microscale climate and dispersion model). The comparison to mast measurements reveals that the model underestimates the wind speeds within the first few meters above the roof, but successfully reproduces wind conditions at 10 m above the roof top (corresponding to about 0.5 times the building height). Scenario simulations with different building configurations at the adjacent property result in an increase or decrease of wind speed above roof top depending on the flow direction at the upper boundary of the urban canopy layer (UCL). The maximum increase or decrease in wind speed caused by the alternations in building structure nearby is found to be in the order of 10%. For the energy yield of a roof-mounted small wind turbine at this site, wind speed changes of this magnitude are negligible due to the generally low prevailing wind speeds of about 3.5 m s−1. Nevertheless, wind speed changes of this order could be significant for wind energy yield in urban areas with higher mean wind speeds. This effect in any case needs to be considered in siting and conducting an urban meteorological monitoring network in order to ensure the homogeneity of observed time-series and may alter the emission and dispersion of pollutants or odor at roof level.

Pemodelan Penggunaaan Energi Turbin Angin Untuk Daerah Manado

Jurnal MIPA ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 188
Author(s):  
Alfrets Septy Wauran
Keyword(s):  
Renewable Energy ◽  
Wind Speed ◽  
Modeling And Simulation ◽  
Wind Turbine ◽  
Statistical Models ◽  
Input Data ◽  
Physical Models ◽  
Continuous Data ◽  
Wind Speed Data ◽  
Wind Speeds

Salah satu renewable energy yang berkembang terutama di Indonesia saat ini adalah turbin angin. Penelitian ini bertujuan membuat suatu pemodelan dan simulasi dari suatu tipe wind turbine dengan menggunakan data real dan kontinyu dari kecepatan angin yang ada di daerah Manado. Dengan hasil yang dibuat maka dapat diprediksi berapa besar daya yang dapat dihasilkan oleh wind turbine tersebut jika diguanakan di daerah Manado. Dengan demikian dapat dilakukan analisa selanjutnya untuk penerapan renewable energy ini dikalkulasi dengan jumlah daya yang diperlukan oleh masyarakat sehingga penggunaannya sangatlah efektif dan efisien. Pemodelan dan simulasi yang akan dilakukan berupa phisycal dan statistical model dengan menggunakan data kecepatan angin dari NASA selama 1 tahun. Software yang akan digunakan untuk pemodelan dan simulasi tersebut adalah Matlab yang dapat menggabungkan input data yang kontinyu dengan physical model. Adapun pembuatan model dan simulasi ini akan dilakukan melalui tahapan-tahapan sebagai berikut: tahapan perancangan sistem yang mencakup perangkat lunak, tahapan pembuatan model yang mencakup pembuatan perangkat lunak, tahapan pengujian sistem yang mencakup pengujian model, perangkat lunak serta simulasi sistem dengan menggunakan data kecepatan anginOne renewable energy that is developing especially in Indonesia today is wind turbines .This study aims to make a modeling and simulation of a type of wind turbine using real and continuous data from wind speeds in the Manado area. With the results made, it can be predicted how much power can be produced by the wind turbine if used in the Manado area. Thus, further analysis can be done for the application of renewable energy, which is calculated by the amount of power needed by the community so that its use is very effective and efficient. Modeling and simulation will be carried out in the form of physical and statistical models using wind speed data from NASA for 1 year. The software that will be used for modeling and simulation is Matlab which can combine continuous input data with physical models. The modeling and simulation will be carried out through the stages as follows: the stage of system design that includes software, the stage of making models that include software creation, the stage of system testing which includes testing of models, software and system simulations using wind speed data 

scholarly journals More accurate aeroelastic wind-turbine load simulations using detailed inflow information

2019 ◽  
Vol 4 (2) ◽  
pp. 303-323
Author(s):  
Mads Mølgaard Pedersen ◽  
Torben Juul Larsen ◽  
Helge Aagaard Madsen ◽  
Gunner Christian Larsen
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbulence Intensity ◽  
Atmospheric Stability ◽  
Pitot Tube ◽  
Wind Speeds ◽  
Inflow Turbulence ◽  
Mean Wind Speed ◽  
Fatigue Loads ◽  
Aeroelastic Simulations

Abstract. In this paper, inflow information is extracted from a measurement database and used for aeroelastic simulations to investigate if using more accurate inflow descriptions improves the accuracy of the simulated wind-turbine fatigue loads. The inflow information is extracted from nearby meteorological masts (met masts) and a blade-mounted five-hole pitot tube. The met masts provide measurements of the inflow at fixed positions some distance away from the turbine, whereas the pitot tube measures the inflow while rotating with the rotor. The met mast measures the free-inflow velocity; however the measured turbulence may evolve on its way to the turbine, pass beside the turbine or the mast may be in the wake of the turbine. The inflow measured by the pitot tube, in comparison, is very representative of the wind that acts on the turbine, as it is measured close to the blades and also includes variations within the rotor plane. Nevertheless, this inflow is affected by the presence of the turbine; therefore, an aerodynamic model is used to estimate the free-inflow velocities that would have occurred at the same time and position without the presence of the turbine. The inflow information used for the simulations includes the mean wind speed field and trend, the turbulence intensity, the wind-speed shear profile, atmospheric stability-dependent turbulence parameters, and the azimuthal variations within the rotor plane. In addition, instantaneously measured wind speeds are used to constrain the turbulence. It is concluded that the period-specific turbulence intensity must be used in the aeroelastic simulations to make the range of the simulated fatigue loads representative for the range of the measured fatigue loads. Furthermore, it is found that the one-to-one correspondence between the measured and simulated fatigue loads is improved considerably by using inflow characteristics extracted from the pitot tube instead of using the met-mast-based sensors as input for the simulations. Finally, the use of pitot-tube-recorded wind speeds to constrain the inflow turbulence is found to significantly decrease the variation of the simulated loads due to different turbulence realizations (seeds), whereby the need for multiple simulations is reduced.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Wind Power potential in Kigali and Western provinces of Rwanda

2015 ◽  
Vol 2 (1) ◽  
pp. 25-36
Author(s):  
Otieno Fredrick Onyango ◽  
Sibomana Gaston ◽  
Elie Kabende ◽  
Felix Nkunda ◽  
Jared Hera Ndeda
Keyword(s):  
Wind Speed ◽  
Probability Density ◽  
Wind Power ◽  
Wind Direction ◽  
Small Scale ◽  
Energy Potential ◽  
Wind Speeds ◽  
Mean Wind Speed ◽  
Wind Energy Potential ◽  
Low Wind Speeds

Wind speed and wind direction are the most important characteristics for assessing wind energy potential of a location using suitable probability density functions. In this investigation, a hybrid-Weibull probability density function was used to analyze data from Kigali, Gisenyi, and Kamembe stations. Kigali is located in the Eastern side of Rwanda while Gisenyi and Kamembe are to the West. On-site hourly wind speed and wind direction data for the year 2007 were analyzed using Matlab programmes. The annual mean wind speed for Kigali, Gisenyi, and Kamembe sites were determined as 2.36m/s, 2.95m/s and 2.97m/s respectively, while corresponding dominant wind directions for the stations were ,  and  respectively. The annual wind power density of Kigali was found to be  while the power densities for Gisenyi and Kamembe were determined as and . It is clear, the investigated regions are dominated by low wind speeds thus are suitable for small-scale wind power generation especially at Kamembe site.

Probabilistic Analysis of List Data for the Estimation of Extreme Design Loads for Wind Turbine Components

2003 ◽  
Author(s):  
M. D. Pandey ◽  
H. J. Sutherland
Keyword(s):  
Wind Turbine ◽  
Sampling Error ◽  
Field Measurements ◽  
Structural Data ◽  
Value Theory ◽  
Extreme Value ◽  
Sampling Errors ◽  
Extreme Loads ◽  
Mean Wind Speed ◽  
Design Loads

Robust estimation of wind turbine design loads for service lifetimes of 30 to 50 years that are based on field measurements of a few days is a challenging problem. Estimating the long-term load distribution involves the integration of conditional distributions of extreme loads over the mean wind speed and turbulence intensity distributions. However, the accuracy of the statistical extrapolation is fairly sensitive to both model and sampling errors. Using measured inflow and structural data from the LIST program, this paper presents a comparative assessment of extreme loads using three distributions: namely, the Gumbel, Weibull and Generalized Extreme Value distributions. The paper uses L-moments, in place of traditional product moments, to reduce the sampling error. The paper discusses the application of extreme value theory and highlights its practical limitations. The proposed technique has the potential of improving estimates of the design loads for wind turbines.

scholarly journals Calibration of Reanalysis Data against Wind Measurements for Energy Production Estimation of Building Integrated Savonius-Type Wind Turbine

2020 ◽  
Vol 10 (24) ◽  
pp. 9017
Author(s):  
Andoni Gonzalez-Arceo ◽  
Maitane Zirion-Martinez de Musitu ◽  
Alain Ulazia ◽  
Mario del Rio ◽  
Oscar Garcia
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Energy Production ◽  
Cost Effective ◽  
Reanalysis Data ◽  
Small Scale ◽  
Wide Range ◽  
Wind Measurements ◽  
Scale Experiment ◽  
Wind Resource

In this work, a cost-effective wind resource method specifically developed for the ROSEO-BIWT (Building Integrated Wind Turbine) and other Building Integrated Wind Turbines is presented. It predicts the wind speed and direction at the roof of an previously selected building for the past 10 years using reanalysis data and wind measurements taken over a year. To do so, the reanalysis wind speed data is calibrated against the measurements using different kinds of quantile mapping, and the wind direction is predicted using random forest. A mock-up of a building and a BIWT were used in a wind tunnel to perform a small-scale experiment presented here. It showed that energy production is possible and even enhanced over a wide range of attack angles. The energy production estimations made with the best performing kind of calibration achieved an overall relative error of 6.77% across different scenarios.

scholarly journals Numerical Simulation of the Aeroelastic Response of Wind Turbines in Typhoons Based on the Mesoscale WRF Model

2019 ◽  
Vol 12 (1) ◽  
pp. 34
Author(s):  
Long Wang ◽  
Cheng Chen ◽  
Tongguang Wang ◽  
Weibin Wang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Direction ◽  
Flow Direction ◽  
Wrf Model ◽  
Normal Operation ◽  
Average Wind Speed ◽  
Aeroelastic Response ◽  
Response Characteristics ◽  
Wind Speeds

A new simulation method for the aeroelastic response of wind turbines under typhoons is proposed. The mesoscale Weather Research and Forecasting (WRF) model was used to simulate a typhoon’s average wind speed field. The measured power spectrum and inverse Fourier transform method were coupled to simulate the pulsating wind speed field. Based on the modal method and beam theory, the wind turbine model was constructed, and the GH-BLADED commercial software package was used to calculate the aerodynamic load and aeroelastic response. The proposed method was applied to assess aeroelastic response characteristics of a commercial 6 MW offshore wind turbine under different wind speeds and direction variation patterns for the case study of typhoon Hagupit (2008), with a maximal wind speed of 230 km/h. The simulation results show that the typhoon’s average wind speed field and turbulence characteristics simulated by the proposed method are in good agreement with the measured values: Their difference in the main flow direction is only 1.7%. The scope of the wind turbine blade in the typhoon is significantly larger than under normal wind, while that under normal operation is higher than that under shutdown, even at low wind speeds. In addition, an abrupt change in wind direction has a significant impact on wind turbine response characteristics. Under normal operation, a sharp variation of the wind direction by 90 degrees in 6 s increases the wind turbine (WT) vibration scope by 27.9% in comparison with the case of permanent wind direction. In particular, the maximum deflection of the wind tower tip in the incoming flow direction reaches 28.4 m, which significantly exceeds the design standard safety threshold.

scholarly journals Analysis of the Patent of a Protective Cover for Vertical-Axis Wind Turbines (VAWTs): Simulations of Wind Flow

2020 ◽  
Vol 12 (18) ◽  
pp. 7818
Author(s):  
Jose Alberto Moleón Baca ◽  
Antonio Jesús Expósito González ◽  
Candido Gutiérrez Montes
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
High Speed ◽  
Experimental Tests ◽  
Weather Conditions ◽  
Vertical Axis ◽  
Good Alternative ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines

This paper presents a numerical and experimental analysis of the patent of a device to be used in vertical-axis wind turbines (VAWTs) under extreme wind conditions. The device consists of two hemispheres interconnected by a set of conveniently implemented variable section ducts through which the wind circulates to the blades. Furthermore, the design of the cross-section of the ducts allows the control of the wind speed inside the device. These ducts are intended to work as diffusers or nozzles, depending on the needs of the installation site. Simulations were performed for the case of high-speed external wind, for which the ducts act as diffusers to reduce wind speed and maintain a well-functioning internal turbine. Four different patent designs were analyzed, focusing on turbine performance and generated power. The results indicate that the patent allows the generation of electric power for a greater range of wind speeds than with a normal wind turbine. The results support that this patent may be a good alternative for wind power generation in geographic areas with extreme weather conditions or with maintained or strong gusty wind. Experimental tests were carried out on the movement of the blades using the available model. Finally, the power curve of the model of this wind turbine was obtained.

scholarly journals Study on the Influence of Baseline Control System on the Fragility of Large-Scale Wind Turbine considering Seismic-Aerodynamic Combination

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Chenyang Yuan ◽  
Jing Li ◽  
Jianyun Chen ◽  
Qiang Xu ◽  
Yunfei Xie
Keyword(s):  
Control System ◽  
Wind Speed ◽  
Wind Turbine ◽  
Large Scale ◽  
Fragility Curves ◽  
Operating Conditions ◽  
Ground Acceleration ◽  
Wind Speeds ◽  
Speed Range ◽  
Wind Actions

The purpose of this paper is to explore the effect of the baseline control system (BCS) on the fragility of large-scale wind turbine when seismic and wind actions are considered simultaneously. The BCS is used to control the power output by regulating rotor speed and blade-pitch angle in real time. In this study, the fragility analysis was performed and compared between two models using different peak ground acceleration, wind speeds, and specified critical levels. The fragility curves with different wind conditions are obtained using the multiple stripe analysis (MSA) method. The calculation results show that the probability of exceedance specified critical level increases as the wind speed increases in model 1 without considering BCS, while does not have an obvious change in the below-rated wind speed range and has a significant decrease in the above-rated wind speed range in model 2 with considering BCS. The comparison depicts that if the BCS is neglected, the fragility of large-scale wind turbine will be underestimated in around the cut-in wind speed range and overestimated in the over-rated wind speed range. It is concluded that the BCS has a great effect on the fragility especially within the operating conditions when the rated wind speed is exceeded, and it should be considered when estimating the fragility of wind turbine subjected to the interaction of seismic and aerodynamic loads.

Sign in / Sign up

Export Citation Format

Share Document