scholarly journals Development of High Strength, High-Strain-Rate Superplastic Magnesium Alloys.

2001 ◽  
Vol 48 (9) ◽  
pp. 779-783
Author(s):  
Mamoru Mabuchi
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Magnesium Alloys ◽  
High Strain ◽  
High Strength

High Strength and High Strain Rate Superplasticity in Magnesium Alloys

2001 ◽  
Vol 357-359 ◽  
pp. 327-332 ◽  
Author(s):  
Yugang Ma ◽  
Mamoru Mabuchi ◽  
Koji Shimojima ◽  
Yoshimitsu Yamada ◽  
Cui E Wen ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Magnesium Alloys ◽  
High Strain ◽  
High Strength

Tension and Compression Behavior of Pre-Stressed Steel Strands at High Strain Rate

2011 ◽  
Vol 82 ◽  
pp. 154-159 ◽  
Author(s):  
Anatoly M. Bragov ◽  
Ezio Cadoni ◽  
Alexandr Yu. Konstantinov ◽  
Andrey K. Lomunov
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Gauge Length ◽  
Hopkinson Pressure Bar ◽  
Dog Bone ◽  
Tension And Compression ◽  
Set Up

In this paper is described the mechanical characterization at high strain rate of the high strength steel usually adopted for strands. The experimental set-up used for high strain rates testing: in tension and compression was the Split Hopkinson Pressure Bar installed in the Laboratory of Dynamic Investigation of Materials in Nizhny Novgorod. The high strain rate data in tension was obtained with dog-bone shaped specimens of 3mm in diameter and 5mm of gauge length. The specimens were screwed between incident and transmitter bars. The specimens used in compression was a cylinder of 3mm in diameter and 5mm in length. The enhancement of the mechanical properties is quite limited compared the usual reinforcing steels.

Warm-Forging Characteristics and Microstructural Response of Medium-Carbon High-Strength Steels for High-Duty Components

2014 ◽  
Vol 611-612 ◽  
pp. 167-172 ◽  
Author(s):  
Piotr Skubisz ◽  
Łukasz Lisiecki
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Microstructure Evolution ◽  
High Strain ◽  
Deformation Behaviour ◽  
Metal Flow ◽  
High Strength Steels ◽  
High Strength ◽  
Medium Carbon ◽  
Warm Forging

Paper presents deformation behaviour and microstructural response of selected medium-carbon high-strength steels commonly used for high-duty components deformed under high-strain-rate and warm work temperature range. The investigation of material behaviour is oriented at analysis of hot and warm workability of material and microstructure evolution resultant from deformation mechanisms, strain induced recrystallization and hardening at temperatures of lower forging regime and high strain rate deformation. The effect of these factors on microstructure after forging and subsequent direct-cooling was studied. Metallographic work aided with numerical methods of simulation of the metal flow and microstructure evolution during forging were used to correlate thermo-mechanical parameters observed with microstructure and mechanical properties after forging and cooling.

scholarly journals High Strain Rate Properties of High Strength Steel Sheets

2011 ◽  
Vol 2 (4) ◽  
pp. 109-113 ◽  
Author(s):  
Akihiro Uenishi ◽  
Hiroshi Yoshida ◽  
Shigeru Yonemura ◽  
Shunji Hiwatashi ◽  
Satoshi Hirose ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Steel ◽  
High Strain ◽  
High Strength ◽  
Steel Sheets

scholarly journals High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2098 ◽  
Author(s):  
Olga Yakovtseva ◽  
Maria Sitkina ◽  
Ahmed O. Mosleh ◽  
Anastasia Mikhaylovskaya
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Superplastic Deformation ◽  
High Strain ◽  
Flow Behavior ◽  
Constant Strain Rate ◽  
Superplastic Forming ◽  
High Strength ◽  
Strain Rate Range ◽  
Strain Rates

Increasing the strain rate at superplastic forming is a challenging technical and economic task of aluminum forming manufacturing. New aluminum sheets exhibiting high strain rate superplasticity at strain rates above 0.01 s−1 are required. This study describes the microstructure and the superplasticity properties of a new high-strength Al-Zn-Mg-based alloy processed by a simple thermomechanical treatment including hot and cold rolling. The new alloy contains Ni to form Al3Ni coarse particles and minor additions of Zr (0.19 wt.%) and Sc (0.06 wt.%) to form nanoprecipitates of the L12-Al3 (Sc,Zr) phase. The design of chemical and phase compositions of the alloy provides superplasticity with an elongation of 600–800% in a strain rate range of 0.01 to 0.6/s and residual cavitation less than 2%. A mean elongation-to-failure of 400% is observed at an extremely high constant strain rate of 1 s−1. The strain-induced evolution of the grain and dislocation structures as well as the L12 precipitates at superplastic deformation is studied. The dynamic recrystallization at superplastic deformation is confirmed. The superplastic flow behavior of the proposed alloy is modeled via a mathematical Arrhenius-type constitutive model and an artificial neural network model. Both models exhibit good predictability at low and high strain rates of superplastic deformation.

Compressive Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loading

2011 ◽  
Vol 82 ◽  
pp. 57-62 ◽  
Author(s):  
Sha Sha Wang ◽  
Min Hong Zhang ◽  
Ser Tong Quek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Concrete ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Strain Rates ◽  
Compressive Behavior ◽  
High Strain Rates ◽  
Strength Concrete

This paper presents a laboratory experimental study on the effect of high strain rate on compressive behavior of plain and fiber-reinforce high-strength concrete (FRHSC) with similar strength of 80-90 MPa. Steel fibers, polyethylene fibers, and a combination of these were used in the FRHSC. A split Hopkinson pressure bar equipment was used to determine the concrete behavior at strain rates from about 30 to 300 s-1. The ratio of the strength at high strain rates to that at static loading condition, namely dynamic increase factor (DIF), of the concretes was determined and compared with that recommended by CEB-FIP code. Fracture patterns of the specimens at high strain rates are described and discussed as well. Results indicate that the CEB-FIP equation is applicable to the plain high strength concrete, but overestimates the DIF of the FRHSC at strain rates beyond a transition strain rate of 30 s-1. Based on the experimental results, a modified equation on DIF is proposed for the FRHSC.

Effect of High Strain-Rate Thermomechanical Processing on Microstructure and Mechanical Properties of Ti-10V-2Fe-3Al Alloy

2013 ◽  
Vol 845 ◽  
pp. 96-100 ◽  
Author(s):  
Piotr Skubisz ◽  
Marek Packo ◽  
Katarzyna Mordalska ◽  
Tadeusz Skowronek
Keyword(s):  
Mechanical Properties ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Thermomechanical Processing ◽  
Hot Forging ◽  
High Strength ◽  
Processing Route ◽  
Microstructure And Mechanical Properties ◽  
Processed Material

Results of beta forging of titanium alloy Ti-10V-2Fe-3Al and subsequent thermal treatment are presented, with analysis of the effect of the processing route on the final mechanical properties, correlated with microstructure of thermomechanically processed material. Investigation of response to high strain-rate hot-forging of microstructure and mechanical properties is focused on the effect of the strengthening mechanisms in the material after two common manners of deformation typical of that alloy. The effect of deformation conditions on final microstructure and mechanical properties was analyzed in three crucial stages of thermomechanical processing, e.i. after deformation, quenching and aging. In result, conclusions were formulated as for processing conditions promoting high strength and/or ductility.

Sign in / Sign up

Export Citation Format

Share Document