Study of theoretical and wind tunnel results on flight performance degradation due to leading edge rime ice accretion

Author(s):  
ROBERT GRIFFITHS ◽  
KENNETH KORKAN
2020 ◽  
Vol 92 (6) ◽  
pp. 827-836 ◽  
Author(s):  
Prasad G. ◽  
Bruce Ralphin Rose J.

Purpose The purpose of this paper is to analyse an actual representation of ice accretions, which are important during the certification process. Design/methodology/approach Ice accretion experiments are conducted in a low-speed subsonic wind tunnel testing facility to evaluate the influence of various ice shapes around the airfoil sections. Ice accumulation changes the shapes of local airfoil sections and thereby affects the aerodynamic performance characteristics of the considered NACA 23012 profile. The ice profiles are impregnated using balsa wood with glace, horn and mixed ice accretion cases for the detailed experimental investigation. Findings Computational fluid dynamics analysis is done to compute the influence of different ice shapes on the aerodynamic coefficients (Cl and Cd) while ice accretion occurs at the leading edge of the airfoil sections. It is observed that the Cl and Cd modified immediately more than 40% as compared to the clean wing configuration. In the same fashion, the skin friction coefficient also abruptly changes for different ice shapes that have the potential to induce flutter at the critical speed of the airplane. The computational solutions are further validated through wind tunnel experiments and recent literature concerning certification for flight in icing conditions. Social implications The ice accretion study on the aerodynamic surfaces can also be extended for wind turbine blades installed at different cold regions around the globe. Further, the propeller icing influences the entire rotorcraft aerodynamics at low temperature conditions and the findings of this study are strongly connected with such problems. Originality/value The aerodynamic characteristics of the baseline airfoil are greatly affected by the ice accretion problem. Although flight through icing condition endures for a short duration, the takeoff path and decision speed are determined based on airplane drag as per federal aviation regulations. Hence, the proposed study is focussed on a cost-effective approach to predict the effect of ice accretion to achieve optimum performance.


Author(s):  
Mingqi Huang ◽  
Honggang Yuan ◽  
Liangquan Wang ◽  
Xianmin Peng ◽  
Qinglin Liu

Helicopter rotor performance can be significantly altered by ice accretion which directly degrades the handling qualities and safety during flight. To obtain understanding into the effect of ice accretion on a helicopter rotor in forward flight under different icing environments, an experimental campaign was conducted in an icing wind tunnel using a rotor model with diameter at 2 m. Research was emphasized on revealing effect of liquid water content and static temperature on the rotor performance degradation. The dynamic thrust and torque of the rotor were measured by a six-component balance. Ice shape of the airfoils at specific rotor blade spanwise locations was obtained through the ice cutting process; meanwhile, the entire ice topology on the blade was scanned by means of the three-dimensional scanning technique. Results showed that ice was mainly accreted on the leading edge and lower surface of the blade. The static temperature of a icing cloud has a noticeable effect on the regime of accreted ice. The ice formation was transparent glaze at −8°C and transformed to milky rime when changed the static temperature to −20°C. Comparing to rime ice, the glaze ice on the blade is more influential to the rotor performance degradation. Particular attention is given to the fact that under extreme icing conditions, over 30% degradation of transient rotor thrust was observed.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Rachel M. Starkweather ◽  
Svetlana V. Poroseva ◽  
David T. Hanson

AbstractAn important role that the leading-edge cross-section shape plays in the wing flight performance is well known in aeronautics. However, little is known about the shape of the leading-edge cross section of an insect’s wing and its contribution to remarkable qualities of insect flight. In this paper, we reveal, in the first time, the shape of the leading-edge cross section of a cicada’s wing and analyze its variability along the wing. We also identify and quantify similarities in characteristic dimensions of this shape in the wings of three different cicada species.


2021 ◽  
pp. 0309524X2110071
Author(s):  
Usman Butt ◽  
Shafqat Hussain ◽  
Stephan Schacht ◽  
Uwe Ritschel

Experimental investigations of wind turbine blades having NACA airfoils 0021 and 4412 with and without tubercles on the leading edge have been performed in a wind tunnel. It was found that the lift coefficient of the airfoil 0021 with tubercles was higher at Re = 1.2×105 and 1.69×105 in post critical region (at higher angle of attach) than airfoils without tubercles but this difference relatively diminished at higher Reynolds numbers and beyond indicating that there is no effect on the lift coefficients of airfoils with tubercles at higher Reynolds numbers whereas drag coefficient remains unchanged. It is noted that at Re = 1.69×105, the lift coefficient of airfoil without tubercles drops from 0.96 to 0.42 as the angle of attack increases from 15° to 20° which is about 56% and the corresponding values of lift coefficient for airfoil with tubercles are 0.86 and 0.7 at respective angles with18% drop.


2020 ◽  
Vol 12 ◽  
pp. 175682932097798
Author(s):  
Han Bao ◽  
Wenqing Yang ◽  
Dongfu Ma ◽  
Wenping Song ◽  
Bifeng Song

Bionic micro aerial vehicles have become popular because of their high thrust efficiency and deceptive appearances. Leading edge or trailing edge devices (such as slots or flaps) are often used to improve the flight performance. Birds in nature also have leading-edge devices, known as the alula that can improve their flight performance at large angles of attack. In the present study, the aerodynamic performance of a flapping airfoil with alula is numerically simulated to illustrate the effects of different alula geometric parameters. Different alula relative angles of attack β (the angle between the chord line of the alula and that of the main airfoil) and vertical distances h between the alula and the main airfoil are simulated at pre-stall and post-stall conditions. Results show that at pre-stall condition, the lift increases with the relative angle of attack and the vertical distance, but the aerodynamic performance is degraded in the presence of alula compared with no alula, whereas at post-stall condition, the alula greatly enhances the lift. However, there seems to be an optimal relative angle of attack for the maximum lift enhancement at a fixed vertical distance considering the unsteady effect, which may indicate birds can adjust the alula twisting at different spanwise positions to achieve the best flight performance. Different alula geometric parameters may affect the aerodynamic force by modifying the pressure distribution along the airfoil. The results are instructive for design of flapping-wing bionic unmanned air vehicles.


1992 ◽  
Vol 114 (2) ◽  
pp. 119-124 ◽  
Author(s):  
C. P. Butterfield ◽  
George Scott ◽  
Walt Musial

Horizontal axis wind turbine (HAWT) performance is usually predicted by using wind tunnel airfoil performance data in a blade element momentum theory analysis. This analysis assumes that the rotating blade airfoils will perform as they do in the wind tunnel. However, when stall-regulated HAWT performance is measured in full-scale operation, it is common to find that peak power levels are significantly greater than those predicted. Pitch-controlled rotors experience predictable peak power levels because they do not rely on stall to regulate peak power. This has led to empirical corrections to the stall predictions. Viterna and Corrigan (1981) proposed the most popular version of this correction. But very little insight has been gained into the basic cause of this discrepancy. The National Renewable Energy Laboratory (NREL), funded by the DOE, has conducted the first phase of an experiment which is focused on understanding the basic fluid mechanics of HAWT aerodynamics. Results to date have shown that unsteady aerodynamics exist during all operating conditions and dynamic stall can exist for high yaw angle operation. Stall hysteresis occurs for even small yaw angles and delayed stall is a very persistent reality in all operating conditions. Delayed stall is indicated by a leading edge suction peak which remains attached through angles of attack (AOA) up to 30 degrees. Wind tunnel results show this peak separating from the leading edge at 18 deg AOA. The effect of this anomaly is to raise normal force coefficients and tangent force coefficients for high AOA. Increased tangent forces will directly affect HAWT performance in high wind speed operation. This report describes pressure distribution data resulting from both wind tunnel and HAWT tests. A method of bins is used to average the HAWT data which is compared to the wind tunnel data. The analysis technique and the test set-up for each test are described.


2018 ◽  
Vol 72 ◽  
pp. 01007 ◽  
Author(s):  
Faizan Afzal ◽  
Muhammad S. Virk

This paper describes a brief overview of main issues related to atmospheric ice accretion on wind turbines installed in cold climate region. Icing has significant effects on wind turbine performance particularly from aerodynamic and structural integrity perspective, as ice accumulates mainly on the leading edge of the blades that change its aerodynamic profile shape and effects its structural dynamics due to added mass effects of ice. This research aims to provide an overview and develop further understanding of the effects of atmospheric ice accretion on wind turbine blades. One of the operational challenges of the wind turbine blade operation in icing condition is also to overcome the process of ice shedding, which may happen due to vibrations or bending of the blades. Ice shedding is dangerous phenomenon, hazardous for equipment and personnel in the immediate area.


Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2682 ◽  
Author(s):  
Guang-Hui Ding ◽  
Bing-He Ma ◽  
Jin-Jun Deng ◽  
Wei-Zheng Yuan ◽  
Kang Liu

A micro-floating element wall shear stress sensor with backside connections has been developed for accurate measurements of wall shear stress under the turbulent boundary layer. The micro-sensor was designed and fabricated on a 10.16 cm SOI (Silicon on Insulator) wafer by MEMS (Micro-Electro-Mechanical System) processing technology. Then, it was calibrated by a wind tunnel setup over a range of 0 Pa to 65 Pa. The measurements of wall shear stress on a smooth plate were carried out in a 0.6 m × 0.6 m transonic wind tunnel. Flow speed ranges from 0.4 Ma to 0.8 Ma, with a corresponding Reynold number of 1.05 × 106~1.55 × 106 at the micro-sensor location. Wall shear stress measured by the micro-sensor has a range of about 34 Pa to 93 Pa, which is consistent with theoretical values. For comparisons, a Preston tube was also used to measure wall shear stress at the same time. The results show that wall shear stress obtained by three methods (the micro-sensor, a Preston tube, and theoretical results) are well agreed with each other.


Sign in / Sign up

Export Citation Format

Share Document