CFD Benchmarking of Heat Transfer and Pressure Drop Predictions in a Pin Fin Channel

2015 ◽  
Author(s):  
Royce Fernandes ◽  
Mark A. Ricklick
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Pin Fin

Assessment of heat transfer and pressure drop of metal foam-pin-fin heat sink

2021 ◽  
Vol 170 ◽  
pp. 107109
Author(s):  
Mohanad A. Alfellag ◽  
Hamdi E. Ahmed ◽  
Mohammed Gh. Jehad ◽  
Marwan Hameed
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Metal Foam ◽  
Pin Fin

A Study on Flow Boiling in Microchannel With Piranha Pin Fin

2015 ◽  
Author(s):  
X. Yu ◽  
C. Woodcock ◽  
Y. Wang ◽  
J. Plawsky ◽  
Y. Peles
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Transfer Performance ◽  
Flow Boiling ◽  
Transfer Performance ◽  
Flow Conditions ◽  
Pin Fin ◽  
Flow And Heat Transfer

In this paper we reported an advanced structure, the Piranha Pin Fin (PPF), for microchannel flow boiling. Fluid flow and heat transfer performance were evaluated in detail with HFE7000 as working fluid. Surface temperature, pressure drop, heat transfer coefficient and critical heat flux (CHF) were experimentally obtained and discussed. Furthermore, microchannels with different PPF geometrical configurations were investigated. At the same time, tests for different flow conditions were conducted and analyzed. It turned out that microchannel with PPF can realize high-heat flux dissipation with reasonable pressure drop. Both flow conditions and PPF configuration played important roles for both fluid flow and heat transfer performance. This study provided useful reference for further PPF design in microchannel for flow boiling.

Heat Transfer and Pressure Drop in a Pin Fin Heat Sink Using Nanofluids as Coolant

2015 ◽  
Vol 1105 ◽  
pp. 253-258 ◽  
Author(s):  
Weerapun Duangthongsuk ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Electric Heater ◽  
Uniform Heat Flux ◽  
Heat Transfer Area ◽  
Pin Fin ◽  
Aluminum Material

This research presents an experimental investigation on the heat transfer performance and pressure drop characteristics of a heat sink with miniature square pin fin structure using nanofluids as coolant. ZnO-water nanofluids with particle concentrations of 0.2, 0.4 and 0.6 vol.% are used as working fluid and then compared with the data for water-cooled heat sink. Heat sink made from aluminum material with dimension around 28 x 33 x 25 mm (width x length x thickness). The heat transfer area and hydraulic diameter of the each flow channel is designed at 1,565 mm2and 1.2 mm respectively. Uniform heat flux at the bottom of heat sink is achieved using an electric heater. The experimental data illustrate that the thermal performance of heat sink using nanofluids as coolant is average 14% higher than that of the water-cooled heat sink. For pressure drop, the data show that the pressure drop of nanofluids is a few percent larger than that of the water-cooled heat sink.

scholarly journals Experimental Investigation of Embedded Micropin-Fins for Single-Phase Heat Transfer and Pressure Drop

2018 ◽  
Vol 140 (2) ◽  
Author(s):  
Chirag R. Kharangate ◽  
Ki Wook Jung ◽  
Sangwoo Jung ◽  
Daeyoung Kong ◽  
Joseph Schaadt ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Friction Factor ◽  
Integrated Circuit ◽  
Single Phase ◽  
Absolute Error ◽  
Heat Fluxes ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pin Fin

Three-dimensional (3D) stacked integrated circuit (IC) chips offer significant performance improvement, but offer important challenges for thermal management including, for the case of microfluidic cooling, constraints on channel dimensions, and pressure drop. Here, we investigate heat transfer and pressure drop characteristics of a microfluidic cooling device with staggered pin-fin array arrangement with dimensions as follows: diameter D = 46.5 μm; spacing, S ∼ 100 μm; and height, H ∼ 110 μm. Deionized single-phase water with mass flow rates of m˙ = 15.1–64.1 g/min was used as the working fluid, corresponding to values of Re (based on pin fin diameter) from 23 to 135, where heat fluxes up to 141 W/cm2 are removed. The measurements yield local Nusselt numbers that vary little along the heated channel length and values for both the Nu and the friction factor do not agree well with most data for pin fin geometries in the literature. Two new correlations for the average Nusselt number (∼Re1.04) and Fanning friction factor (∼Re−0.52) are proposed that capture the heat transfer and pressure drop behavior for the geometric and operating conditions tested in this study with mean absolute error (MAE) of 4.9% and 1.7%, respectively. The work shows that a more comprehensive investigation is required on thermofluidic characterization of pin fin arrays with channel heights Hf < 150 μm and fin spacing S = 50–500 μm, respectively, with the Reynolds number, Re < 300.

scholarly journals Boiling Heat Transfer From an Array of Round Jets With Hybrid Surface Enhancements

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Matthew J. Rau ◽  
Suresh V. Garimella ◽  
Ercan M. Dede ◽  
Shailesh N. Joshi
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Flat Surface ◽  
Microporous Layer ◽  
Maximum Heat ◽  
Flow Rates ◽  
Pin Fin ◽  
Pin Fins ◽  
Single Jet

The effect of a variety of surface enhancements on the heat transfer achieved with an array of impinging jets is experimentally investigated using the dielectric fluid HFE-7100 at different volumetric flow rates. The performance of a 5 × 5 array of jets, each 0.75 mm in diameter, is compared to that of a single 3.75 mm diameter jet with the same total open orifice area, in single-and two-phase operation. Four different target copper surfaces are evaluated: a baseline smooth flat surface, a flat surface coated with a microporous layer, a surface with macroscale area enhancement (extended square pin–fins), and a hybrid surface on which the pin–fins are coated with the microporous layer; area-averaged heat transfer and pressure drop measurements are reported. The array of jets enhances the single-phase heat transfer coefficients by 1.13–1.29 times and extends the critical heat flux (CHF) on all surfaces compared to the single jet at the same volumetric flow rates. Additionally, the array greatly enhances the heat flux dissipation capability of the hybrid coated pin–fin surface, extending CHF by 1.89–2.33 times compared to the single jet on this surface, with a minimal increase in pressure drop. The jet array coupled with the hybrid enhancement dissipates a maximum heat flux of 205.8 W/cm2 (heat input of 1.33 kW) at a flow rate of 1800 ml/min (corresponding to a jet diameter-based Reynolds number of 7800) with a pressure drop incurred of only 10.9 kPa. Compared to the single jet impinging on the smooth flat surface, the array of jets on the coated pin–fin enhanced surface increased CHF by a factor of over four at all flow rates.

Lateral-Flow Effect on Endwall Heat Transfer and Pressure Drop in a Pin-Fin Trapezoidal Duct of Various Pin Shapes

2000 ◽  
Vol 123 (1) ◽  
pp. 133-139 ◽  
Author(s):  
Jenn-Jiang Hwang ◽  
Chau-Ching Lu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Flow Rate ◽  
Lateral Flow ◽  
Transfer Enhancement ◽  
Pin Fin ◽  
Flow Reynolds Number ◽  
Outlet Flow ◽  
Flow Through

The effects of lateral-flow ejection 0<ε<1.0, pin shapes (square, diamond, and circular), and flow Reynolds number (6000<Re<40,000) on the endwall heat transfer and pressure drop for turbulent flow through a pin-fin trapezoidal duct are studied experimentally. A staggered pin array of five rows and five columns is inserted in the trapezoidal duct, with the same spacings between the pins in the streamwise and spanwise directions: Sx/d=Sy/d=2.5. Three different-shaped pins of length from 2.5<l/d<4.6 span the distance between two endwalls of the trapezoidal duct. Results reveal that the pin-fin trapezoidal duct with lateral-flow rate of ε=0.3-0.4 has a local minimum endwall-averaged Nusselt number and Euler number for all pin shapes investigated. The trapezoidal duct of lateral outlet flow only (ε=1.0) has the highest endwall heat transfer and pressure drop. Moreover, the square pin results in a better heat transfer enhancement than the diamond pin, and subsequently than the circular pin. Finally, taking account of the lateral-flow rate and the flow Reynolds number, the work develops correlations of the endwall-averaged heat transfer with three different pin shapes.

Sign in / Sign up

Export Citation Format

Share Document