scholarly journals An Improved Fixation Method for Transmission Electron Microscopy for the Histological Study of the Lens

1991 ◽  
Vol 68 (5) ◽  
pp. 295-298 ◽  
Author(s):  
Hideki SAKAI ◽  
Kuniaki TAKATA ◽  
Minoru FUKUDA ◽  
Takaaki FUJIWARA ◽  
Hiroshi HIRANO
2019 ◽  
Author(s):  
Michaela Wenzel ◽  
Marien P. Dekker ◽  
Biwen Wang ◽  
Maroeska J. Burggraaf ◽  
Wilbert Bitter ◽  
...  

AbstractTransmission electron microscopy (TEM) is an important imaging technique in bacterial research and requires ultrathin sectioning of resin embedding of cell pellets. This method consumes milli- to deciliters of culture and results in sections of randomly orientated cells. For rod-shaped bacteria, this makes it exceedingly difficult to find longitudinally cut cells, which precludes large-scale quantification of morphological phenotypes. Here, we describe a new fixation method using either thin agarose layers or carbon-coated glass surfaces that enables flat embedding of bacteria. This technique allows for the observation of thousands of longitudinally cut rod-shaped cells per single section and requires only microliter culture volumes. We successfully applied this technique to Gram-positive Bacillus subtilis, Gram-negative Escherichia coli, the tuberculosis vaccine strain Mycobacterium bovis BCG, and the cell wall-lacking mycoplasma Acholeplasma laidlawii. To assess the potential of the technique to quantify morphological phenotypes, we examined cellular changes induced by a panel of different antibiotics. Surprisingly, we found that the ribosome inhibitor tetracycline causes significant deformations of the cell membrane. Further investigations showed that the presence of tetracycline in the cell membrane changes membrane organization and affects the peripheral membrane proteins MinD, MinC, and MreB, which are important for regulation of cell division and elongation. Importantly, we could show that this effect is not the result of ribosome inhibition but is a secondary antibacterial activity of tetracycline that has defied discovery for more than 50 years.SignificanceBacterial antibiotic resistance is a serious public health problem and novel antibiotics are urgently needed. Before a new antibiotic can be brought to the clinic, its antibacterial mechanism needs to be elucidated. Transmission electron microscopy is an important tool to investigate these mechanisms. We developed a flat embedding method that enables examination of many more bacterial cells than classical protocols, enabling large-scale quantification of phenotypic changes. Flat embedding can be adapted to most growth conditions and microbial species and can be employed in a wide variety of microbiological research fields. Using this technique, we show that even well-established antibiotics like tetracycline can have unknown additional antibacterial activities, demonstrating how flat embedding can contribute to finding new antibiotic mechanisms.


2011 ◽  
Vol 101 (7) ◽  
pp. 894-900 ◽  
Author(s):  
H. H. Edwards ◽  
M. R. Bonde

For over 30 years, it has been known that Phakopsora pachyrhizi is unusual in that it penetrates from urediniospores directly through the leaf cuticle without entering stomates. This unusual mode of penetration suggests that disease resistance mechanisms might exist for soybean rust that do not exist for most rust diseases. As a result, we decided to conduct a histological study using transmission electron microscopy to further elucidate the mechanisms of penetration and early establishment of P. pachyrhizi in soybean leaves. Based on our study, it was concluded that P. pachyrhizi utilizes primarily mechanical force, perhaps with the aid of digestive enzymes, to penetrate the cuticle on the leaf surface. However, the lack of deformation lines in micrographs indicated that digestive enzymes, without mechanical force, are used by the penetration hypha to penetrate the outer and inner epidermal cell walls. Digestive enzymes, again indicated by the lack of deformation lines, are used by haustorial mother cells to breach the walls of mesophyll cells to form haustoria. The possibility exists for eventual determination of the precise roles of pressure and digestive enzymes in the development of soybean rust and elucidation of some of the determinants of resistance and susceptibility to this important plant disease.


Author(s):  
G. G. Shaw

The morphology and composition of the fiber-matrix interface can best be studied by transmission electron microscopy and electron diffraction. For some composites satisfactory samples can be prepared by electropolishing. For others such as aluminum alloy-boron composites ion erosion is necessary.When one wishes to examine a specimen with the electron beam perpendicular to the fiber, preparation is as follows: A 1/8 in. disk is cut from the sample with a cylindrical tool by spark machining. Thin slices, 5 mils thick, containing one row of fibers, are then, spark-machined from the disk. After spark machining, the slice is carefully polished with diamond paste until the row of fibers is exposed on each side, as shown in Figure 1.In the case where examination is desired with the electron beam parallel to the fiber, preparation is as follows: Experimental composites are usually 50 mils or less in thickness so an auxiliary holder is necessary during ion milling and for easy transfer to the electron microscope. This holder is pure aluminum sheet, 3 mils thick.


Author(s):  
R. W. Anderson ◽  
D. L. Senecal

A problem was presented to observe the packing densities of deposits of sub-micron corrosion product particles. The deposits were 5-100 mils thick and had formed on the inside surfaces of 3/8 inch diameter Zircaloy-2 heat exchanger tubes. The particles were iron oxides deposited from flowing water and consequently were only weakly bonded. Particular care was required during handling to preserve the original formations of the deposits. The specimen preparation method described below allowed direct observation of cross sections of the deposit layers by transmission electron microscopy.The specimens were short sections of the tubes (about 3 inches long) that were carefully cut from the systems. The insides of the tube sections were first coated with a thin layer of a fluid epoxy resin by dipping. This coating served to impregnate the deposit layer as well as to protect the layer if subsequent handling were required.


Author(s):  
S. Fujishiro

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.


Author(s):  
Nakazo Watari ◽  
Yasuaki Hotta ◽  
Yoshio Mabuchi

It is very useful if we can observe the identical cell elements within the same sections by light microscopy (LM), transmission electron microscopy (TEM) and/or scanning electron microscopy (SEM) sequentially, because, the cell fine structure can not be indicated by LM, while the color is; on the other hand, the cell fine structure can be very easily observed by EM, although its color properties may not. However, there is one problem in that LM requires thick sections of over 1 μm, while EM needs very thin sections of under 100 nm. Recently, we have developed a new method to observe the same cell elements within the same plastic sections using both light and transmission (conventional or high-voltage) electron microscopes.In this paper, we have developed two new observation methods for the identical cell elements within the same sections, both plastic-embedded and paraffin-embedded, using light microscopy, transmission electron microscopy and/or scanning electron microscopy (Fig. 1).


Author(s):  
R.R. Russell

Transmission electron microscopy of metallic/intermetallic composite materials is most challenging since the microscopist typically has great difficulty preparing specimens with uniform electron thin areas in adjacent phases. The application of ion milling for thinning foils from such materials has been quite effective. Although composite specimens prepared by ion milling have yielded much microstructural information, this technique has some inherent drawbacks such as the possible generation of ion damage near sample surfaces.


Sign in / Sign up

Export Citation Format

Share Document