STUDY OF THE REDUCTION OF THE SERPENTINITOS PARTICLE SIZE TO INCREASE THE EFFICIENCY OF THE PROCESSES OF MINERAL CARBONATION

2018 ◽  
Author(s):  
Natalia Ribeiro Galina ◽  
Gretta Larisa Aurora Arce Ferrufino ◽  
Carlos Manuel Romero Luna ◽  
Ivonete Ávila
Keyword(s):  
Particle Size ◽  
Mineral Carbonation

scholarly journals Influencing Factors of the Mineral Carbonation Process of Iron Ore Mining Waste in Sequestering Atmospheric Carbon Dioxide

2021 ◽  
Vol 13 (4) ◽  
pp. 1866
Author(s):  
Noor Allesya Alis Ramli ◽  
Faradiella Mohd Kusin ◽  
Verma Loretta M. Molahid
Keyword(s):  
Carbon Dioxide ◽  
Particle Size ◽  
Chemical Composition ◽  
Iron Ore ◽  
Divalent Cations ◽  
Mining Industry ◽  
Mining Waste ◽  
Aluminum Silicate ◽  
Mineral Carbonation ◽  
Carbonation Process

Mining waste may contain potential minerals that can act as essential feedstock for long-term carbon sequestration through a mineral carbonation process. This study attempts to identify the mineralogical and chemical composition of iron ore mining waste alongside the effects of particle size, temperature, and pH on carbonation efficiency. The samples were found to be alkaline in nature (pH of 6.9–7.5) and contained small-sized particles of clay and silt, thus indicating their suitability for mineral carbonation reactions. Samples were composed of important silicate minerals needed for the formation of carbonates such as wollastonite, anorthite, diopside, perovskite, johannsenite, and magnesium aluminum silicate, and the Fe-bearing mineral magnetite. The presence of Fe2O3 (39.6–62.9%) and CaO (7.2–15.2%) indicated the potential of the waste to sequester carbon dioxide because these oxides are important divalent cations for mineral carbonation. The use of small-sized mine-waste particles enables the enhancement of carbonation efficiency, i.e., particles of <38 µm showed a greater extent of Fe and Ca carbonation efficiency (between 1.6–6.7%) compared to particles of <63 µm (0.9–5.7%) and 75 µm (0.7–6.0%). Increasing the reaction temperature from 80 °C to 150–200 °C resulted in a higher Fe and Ca carbonation efficiency of some samples between 0.9–5.8% and 0.8–4.0%, respectively. The effect of increasing the pH from 8–12 was notably observed in Fe carbonation efficiency of between 0.7–5.9% (pH 12) compared to 0.6–3.3% (pH 8). Ca carbonation efficiency was moderately observed (0.7–5.5%) as with the increasing pH between 8–10. Therefore, it has been evidenced that mineralogical and chemical composition were of great importance for the mineral carbonation process, and that the effects of particle size, pH, and temperature of iron mining waste were influential in determining carbonation efficiency. Findings would be beneficial for sustaining the mining industry while taking into account the issue of waste production in tackling the global carbon emission concerns.

scholarly journals How Ph.D. Students Start a Research

2021 ◽  
pp. 41-54
Author(s):  
Muhammad Imran Rashid
Keyword(s):  
Particle Size ◽  
Xrd Analysis ◽  
Ph Measurement ◽  
Mineral Carbonation ◽  
Size Measurement ◽  
Particle Size Measurement ◽  
Measuring Techniques ◽  
Basic Need ◽  
Personal Research ◽  
Tga Analysis

In education pedagogy, its necessary to prioritize tasks and jobs. Learn operating the reactor or required apparatus but most important first. Regarding measuring techniques (PSD measurement, pH measurement, XRD, SEM/EDS), learn more basic and fundamental techniques first followed by complimentary techniques. Regarding mineral carbonation, operation of reactor is a basic need followed by particle size measurement using Malvern Mastersizer and powders samples XRD analysis and identifying the phases and verifying those phases through TGA analysis. This article illustrates author personal research of 4 initial 4 months duration. Month wise progress is presented in this article in an interesting way.

Microstructural characterization of laser-melted/roller-quenched dicalcium silicate

1988 ◽  
Vol 46 ◽  
pp. 582-583
Author(s):  
C. J. Chan ◽  
K. R. Venkatachari ◽  
W. M. Kriven ◽  
J. F. Young
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Shape Change ◽  
Microstructural Characterization ◽  
Particle Size Effect ◽  
Dicalcium Silicate ◽  
Laser Melting ◽  
Uniform Size ◽  
Cell Shape Change ◽  
Wide Range

Dicalcium silicate (Ca2SiO4) is a major component of Portland cement. It has also been investigated as a potential transformation toughener alternative to zirconia. It has five polymorphs: α, α'H, α'L, β and γ. Of interest is the β-to-γ transformation on cooling at about 490°C. This transformation, accompanied by a 12% volume increase and a 4.6° unit cell shape change, is analogous to the tetragonal-to-monoclinic transformation in zirconia. Due to the processing methods used, previous studies into the particle size effect were limited by a wide range of particle size distribution. In an attempt to obtain a more uniform size, a fast quench rate involving a laser-melting/roller-quenching technique was investigated.The laser-melting/roller-quenching experiment used precompacted bars of stoichiometric γ-Ca2SiO4 powder, which were synthesized from AR grade CaCO3 and SiO2xH2O. The raw materials were mixed by conventional ceramic processing techniques, and sintered at 1450°C. The dusted γ-Ca2SiO4 powder was uniaxially pressed into 0.4 cm x 0.4 cm x 4 cm bars under 34 MPa and cold isostatically pressed under 172 MPa. The γ-Ca2SiO4 bars were melted by a 10 KW-CO2 laser.

Analytical Electron Microscopy study of two vehicle-aged automotive exhaust catalysts having dissimilar activities

1989 ◽  
Vol 47 ◽  
pp. 272-273
Author(s):  
Sooho Kim ◽  
M. J. D’Aniello
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Noble Metal ◽  
Catalyst Deactivation ◽  
Analytical Electron Microscopy ◽  
Microscopy Study ◽  
Metal Particles ◽  
Automotive Exhaust ◽  
Exhaust Catalysts ◽  
Analytical Electron

Automotive catalysts generally lose-agtivity during vehicle operation due to several well-known deactivation mechanisms. To gain a more fundamental understanding of catalyst deactivation, the microscopic details of fresh and vehicle-aged commercial pelleted automotive exhaust catalysts containing Pt, Pd and Rh were studied by employing Analytical Electron Microscopy (AEM). Two different vehicle-aged samples containing similar poison levels but having different catalytic activities (denoted better and poorer) were selected for this study.The general microstructure of the supports and the noble metal particles of the two catalysts looks similar; the noble metal particles were generally found to be spherical and often faceted. However, the average noble metal particle size on the poorer catalyst (21 nm) was larger than that on the better catalyst (16 nm). These sizes represent a significant increase over that found on the fresh catalyst (8 nm). The activity of these catalysts decreases as the observed particle size increases.

Effect of particle size on erosion measurements and predictions in annular flow for an elbow

Wear ◽  
2020 ◽  
pp. 203579
Author(s):  
G. Haider ◽  
M. Othayq ◽  
J. Zhang ◽  
R.E. Vieira ◽  
S.A. Shirazi
Keyword(s):  
Particle Size ◽  
Annular Flow ◽  
Effect Of Particle Size
Sign in / Sign up

Export Citation Format

Share Document