scholarly journals Treatment of Iraqi Municipal Wastewater by up-flow Anaerobic Sludge Blanket Reactor UASB

2021 ◽  
Vol 39 (1A) ◽  
pp. 130-136
Author(s):  
Khairi R. Kalash ◽  
Majid A. Dixon ◽  
Hussein IR. Sultan ◽  
Raad A. Ali
Keyword(s):  
Volatile Fatty Acids ◽  
Municipal Wastewater ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Load ◽  
Anaerobic Sludge ◽  
Treated Effluent ◽  
Load Rate ◽  
Anaerobic Sludge Blanket ◽  
Organic Load Rate

In this work, the Upflow Anaerobic Sludge Blanket “UASB” reactor treated effluent wastewater to investigate the process performance on a pilot plant scale. Municipal wastewater at high and medium strength with different organic load rate OLR (0.6-9) kg COD m-3day-1 with the flow of 20 l/h, up-flow velocity 0.4 m/h, hydraulic retention time HRT 9 h at a temperature of (20-30 ºC) was evaluated. The wastewater concentration, including TSS, COD was measured, and the removal efficiencies of chemical oxygen demand (COD) and total suspended solid TSS were calculated and summarized as 45-85% and 70-75%, respectively, depending on organic load rate OLR. Effluent volatile fatty acids VFA was measured, and the results were in the range between 12-90 mg/L depending on OLR with a slight change in pH (8.3-8.4), which means the conversion of COD to methane and increase ammonia concentration.

Treatment of slaughterhouse wastewater in upflow anaerobic sludge blanket reactor

2011 ◽  
Vol 63 (5) ◽  
pp. 877-884 ◽  
Author(s):  
P. Mijalova Nacheva ◽  
M. Reyes Pantoja ◽  
E. A. Lomelí Serrano
Keyword(s):  
Volatile Fatty Acids ◽  
Removal Rate ◽  
Additional Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Load ◽  
Anaerobic Sludge ◽  
Yield Coefficient ◽  
Slaughterhouse Wastewater ◽  
Anaerobic Sludge Blanket

The performance of an upflow anaerobic sludge blanket (UASB) reactor operated at ambient temperature (20.9–25.2°C) was analysed for the treatment of slaughterhouse wastewater previously pre-treated for solid separation. The experimental work was carried out in a reactor with 15 L effective volume. Four organic loads were applied and the process performance was evaluated. The COD removal rate increased with the load rise from 4 to 15 kg COD.m−3.d−1. Removal efficiencies of 90% were obtained with a load of 15 kg COD.m−3.d−1. The entrapment of suspended solids in the sludge blanket was greater in proportion during the first two stages due to the low upflow velocities used when loads of 4 and 7 kg COD.m−3.d−1 were evaluated. This phenomenon did not affect the structure of the biological grains or their methanogenic activity. More than 50% of the organic nitrogen was degraded, causing a 3% increase of ammonia concentration. The concentrations of the volatile fatty acids were not high and the wastewater alkalinity was enough to prevent acidification. The yield coefficient of methane production increased with the load rise, reaching 0.266 m3/kg CODremoved at 15 kg COD.m−3.d−1 organic load. The UASB reactor is a good option for the biological treatment of pre-treated slaughterhouse wastewater. However, additional treatment is required in order to accomplish the water quality requirements in discharges to water bodies.

scholarly journals Carbamazepine removal from low-strength municipal wastewater using a combined UASB-MBR treatment system

2021 ◽  
Vol 83 (8) ◽  
pp. 1920-1931
Author(s):  
M. J. Moya-Llamas ◽  
A. Trapote ◽  
D. Prats
Keyword(s):  
Volatile Fatty Acids ◽  
Municipal Wastewater ◽  
Biogas Production ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Load ◽  
Anaerobic Sludge ◽  
Operational Parameters ◽  
Low Strength ◽  
The Impact

Abstract An Upflow Anaerobic Sludge Blanket reactor combined with a two-stage membrane bioreactor were operated for 193 days in order to evaluate the biological removal of carbamazepine (CBZ) from low-strength municipal wastewater. The system worked in three different organic load stages (0.7 ± 0.1 kg COD·m−3·d−1, 0.4 ± 0.1 kg COD·m−3·d−1 and 0.1 ± 0.0 kg COD·m−3·d−1) to assess the impact of the influent OLR on operational parameters such as anaerobic and aerobic sludge retention time (SRT), acidity, volatile fatty acids (VFAs), biomass activity or biogas production. The highest carbamazepine removals were achieved during the anaerobic stage (UASB reactor), reaching averages of 48.9%, 48.0% and 38.2% operating at high, medium and low OLR, respectively. The aerobic treatment (MBR) served as post-treatment, improving the removals, and the global UASB-MBR system reached averages of 70.0%, 59.6% and 49.8% when the influent was at medium and low OLR, respectively. The results demonstrate the potential of combined biological systems on the removal of recalcitrant pharmaceuticals.

scholarly journals A VFA-based controller for anaerobic digestion of industrial winery wastewater

2018 ◽  
Vol 78 (9) ◽  
pp. 1871-1878 ◽  
Author(s):  
Gustavo Vargas-Morales ◽  
Rolando Chamy ◽  
Santiago García-Gen
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Variable Gain ◽  
Winery Wastewater ◽  
Empirical Function ◽  
Anaerobic Sludge Blanket

Abstract A variable-gain controller for anaerobic digestion of industrial winery wastewater is presented. A control law using both volatile fatty acids (VFA) and methane production rate as controlled variables and organic loading rate (OLR) as manipulated variable is defined. The process state is quantitatively estimated by an empirical function comparing VFA measurements against a setpoint value; then, it is modified with a second empirical function that compares the methane flow rate with a maximum capacity reference, and finally it is adjusted with a third factor considering the actual hydraulic retention time. The variable-gain function determines the extent of the OLR change applied to the system. The controller was successfully validated in a 95 L upflow-anaerobic-sludge-blanket (UASB) reactor, treating industrial wine wastewater at OLR ranged between 2.0 and 39.2 g COD/L d for 120 days at mesophilic conditions. Higher performance was achieved contrasted with a conventional strategy carried out in a parallel UASB unit.

scholarly journals Acclimatization Process on Hybrid Upflow Anaerobic Sludge Blanket Reactor (HUASBR) using Bioball as Growth Media with OLR Variation for Treating Tofu Wastewater

2018 ◽  
Vol 34 (6) ◽  
pp. 3100-3105
Author(s):  
Nyimas Yanqoritha ◽  
Muhammad Turmuzi ◽  
Irvan Irvan ◽  
Fatimah Batubara ◽  
Ilmi Ilmi
Keyword(s):  
Removal Efficiency ◽  
Biogas Production ◽  
Liquid Waste ◽  
Upflow Anaerobic Sludge Blanket ◽  
Organic Load ◽  
Anaerobic Sludge ◽  
Growth Media ◽  
Anaerobic Process ◽  
Load Rate ◽  
Anaerobic Sludge Blanket

Wastewater of tofu industry contains very high organic content, then anaerobic process is the most suitable for degrading this liquid waste. The hybrid upflow anaerobic sludge blanket reactor (HUASBR) was applied in this study because it has the advantage in ensuring good contact between biomass and substrate where a suspension medium and anaerobic filter are able to withstand more biomass in the attached media. Processing Anaerobic process is carried out with the help of bacteria where bacteria need seeding and acclimatization. Acclimatization is the process of adaptation of microorganisms to wastewater to be treated. This adaptation process is carried out by adding waste water from the smallest concentration to the actual concentration. The purpose of this study is to determine the effect of variations in organic load rate (OLR) on the acclimatization process in removing COD, biogas production in accordance with the pH of the anaerobic degradation process so that the optimal process of the acclimatization process can be obtained. In this study, the acclimatization process took 200 days with variation of OLR in the range of 1.5 - 5.9 kg COD m-3 d-1 at HRT 24 hours and flow rate up (Vup) of 0.08 m/h. The objective of OLR variation was to evaluate acclimatization process on the HUASBR performance during process optimization. The highest biogas production and removal efficiency of COD were achieved in pH range of 6.5 - 7.6. While, the highest COD removal efficiency obtained was 86.57% on the 140th day and biogas production 7700 ml for OLR 4.8 kg COD m-3d-1 at HRT 24 h. Consequently, the optimum OLR for treating the tofu wastewater could be achieved up to 4.8 kg COD m-3d-1 and HRT 24h.

Comparison of start-up of an upflow anaerobic sludge blanket reactor and a polyurethane carrier reactor

1996 ◽  
Vol 34 (5-6) ◽  
pp. 509-515 ◽  
Author(s):  
Huub J. Gijzen ◽  
Frank Kansiime
Keyword(s):  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Operational Conditions ◽  
Start Up ◽  
And Performance ◽  
Anaerobic Sludge Blanket

The start-up and performance of an Upflow Anaerobic Sludge Blanket (UASB) reactor and a Polyurethane Carrier Reactor (PCR) was investigated under similar operational conditions. The presence of polyurethane cubes as a carrier material in the PCR resulted in fast reactor start-up due to quick immobilization of methanogenic associations. Start-up of the UASB was slower compared to the PCR, which was mainly reflected in a lower biogas production and acetate degradation efficiency. However, when enough biomass had accumulated in the UASB reactor after 15 weeks of operation, the performance of the two reactors was almost the same in terms of biogas production and volatile fatty acids degradation. Efficient VFA degradation (about 90%) and biogas production (5.2 l/l.d) were achieved at an organic loading rate of 13.2 g/l.d) and HRT of 6 h. When hydraulic retention time was subsequently reduced from 6 to 2 h, the performance of the UASB reactor was better than that of the PCR. The inferior performance of the PCR may have been attributed to channelling of the influent in the reactor at high liquid flow rate.

scholarly journals Microbial Removal of Pb(II) Using an Upflow Anaerobic Sludge Blanket (UASB) Reactor

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 512
Author(s):  
Jeremiah Chimhundi ◽  
Carla Hörstmann ◽  
Evans M. N. Chirwa ◽  
Hendrik G. Brink
Keyword(s):  
Treatment Process ◽  
Removal Rate ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Anaerobic Sludge ◽  
Reduction Potentials ◽  
Oxidation Reduction ◽  
Anaerobic Sludge Blanket ◽  
Microbial Removal ◽  
Maximum Removal

The main objective of this study was to achieve the continuous biorecovery and bioreduction of Pb(II) using an industrially obtained consortia as a biocatalyst. An upflow anaerobic sludge blanket reactor was used in the treatment process. The bioremediation technique that was applied made use of a yeast extract as the microbial substrate and Pb(NO3)2 as the source of Pb(II). The UASB reactor exhibited removal efficiencies of between 90 and 100% for the inlet Pb concentrations from 80 to 2000 ppm and a maximum removal rate of 1948.4 mg/(L·d) was measured. XRD and XPS analyses of the precipitate revealed the presence of Pb0, PbO, PbS and PbSO4. Supporting experimental work carried out included growth measurements, pH, oxidation–reduction potentials and nitrate levels.

KINETIC MODELS FOR PREDICTION OF COD EFFLUENT FROM UPFLOW ANAEROBIC SLUDGE BLANKET (UASB) REACTOR FOR CANNERY SEAFOOD WASTEWATER TREATMENT

2016 ◽  
Vol 78 (5-6) ◽  
Author(s):  
Sunwanee Jijai ◽  
Chairat Siripatana ◽  
Sompong O-Thong ◽  
Norli Ismail
Keyword(s):  
Palm Oil ◽  
Kinetic Models ◽  
Second Order ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Anaerobic Sludge ◽  
Substrate Removal ◽  
Reactor Kinetic ◽  
Palm Oil Mill ◽  
Anaerobic Sludge Blanket

The three identical lab-scale upflow anaerobic sludge blanket (UASB) reactors were operated continuously for treating cannery seafood wastewater at seven hydraulic retention times (HRTs) of 5, 4, 3, 2, 1, 0.5 and 0.25 days. The different of granule sizes from three sources: a cassava factory (CS), a seafood factory (SS), and a palm oil mill (PS), average sizes in the range 1.5-1.7, 0.7-1.0 and 0.1-0.2 mm respectively were used as inocula for anaerobic digestion. The UASB-R1 used only granules from seafood factory (R1-SS), the UASB-R2 used mixed granules from seafood with cassava factory (R2-SS+CS) and the UASB-R3 used mixed granules from seafood factory with palm oil mill (R3-SS+PS). In this study selected mathematical models including Monod, Contois, Grau second-order and modified Stover-Kicannon kinetic models were applied to determine the substrate removal kinetics of UASB reactor. Kinetic parameters were determined through linear regression using experimental data obtained from the steady-state experiment and subsequently used to predict effluent COD. The results showed that Grau second-order and modified Stover-Kicannon kinetic models were more suitable than that of others for predicting the effluent COD, with high the correlation coefficient (R2). In addition, the UASB-R2 from mixed granules with cassava factory (SS+CS) gave the best performance and highest coefficient value.

Sign in / Sign up

Export Citation Format

Share Document