scholarly journals Chemical Synthesis, Functionalization and Characterization of Multiwalled Carbon Nanotubes

2020 ◽  
Vol 6 (3) ◽  
pp. 905-907
Author(s):  
S.S. Gautam ◽  
G.P. Satsangi ◽  
V.R. Satsangi
Keyword(s):  
Carbon Nanotubes ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Fourier Transform Infrared Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Functionalized Mwcnts

This research work is attempted to synthesize, functionalize and to characterize multi walled carbon nanotubes (MWCNTs). The synthesis of multi walled carbon nanotubes was done by chemical vapor deposition (CVD) method. The characterization of MWCNTs was done by adopting the following techniques such as field emission scanning electron microscope, X-ray diffraction, Fourier-transform infrared spectroscopy. The crystalline quality of MWCNTs was confirmed from the analysis of X-ray diffraction pattern. FE-SEM image obtained for MWCNTs and functionalized MWCNTs and it has been seen that dimeter of most of the MWCNTs lies around 90 nm, where as, functionalized MWCNTs diameter is smaller i.e., around 35 nm only. Fourier-transform infrared spectroscopy study confirmed the presence of –COOH and H- bonded –OH in functionalized MWCNTs.

Preparation and characterization of poly(tetramethyl-p-phenylenediamine)/clay hybrids via intercalative polymerization

2003 ◽  
Vol 18 (2) ◽  
pp. 482-486 ◽  
Author(s):  
Guangming Chen ◽  
Nobuo Iyi ◽  
Taketoshi Fujita
Keyword(s):  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Thermal Behavior ◽  
Fourier Transform Infrared Spectroscopy ◽  
Interlayer Space ◽  
X Ray Diffraction ◽  
X Ray ◽  
Noncovalent Bonding ◽  
Intercalative Polymerization

New noncovalent bonding polymer/clay hybrids were prepared, including the polymer poly(tetramethyl-p-phenylenediamine) (poly-TMPD). Polymerization occurred in the interlayer space of clay mineral successively after intercalation of monomers. Two types of clay minerals with different surface properties—a hydrophilic lithium fluorotaeniolite (TN) and four kinds of organophilic fluorotaeniolites (org-TNs)—were used as the hosts. Powder x-ray diffraction results showed an increase of 0.7–1.0 nm in the basal spacings, indicating the formation of poly–TMPD in the interlayer space of the hosts. Intercalative polymerization was also supported by Fourier transform infrared spectroscopy. The orientation of the poly-TMPD and thermal behavior were also discussed.

Preparation and Characterization of Lizardite

2014 ◽  
Vol 556-562 ◽  
pp. 109-112
Author(s):  
Shu Min Zheng ◽  
Kai Ming Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Fourier Transform Infrared Spectroscopy ◽  
Hydrothermal Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Lizardite were synthesized by hydrothermal reaction in an Fe3+doped solution/environment using nanometer SiO2and MgO as precursors. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR). The results show that: the synthetic samples are lizardite with a thickness ranging from 60 nm to 200 nm in the temperature range 200°C~230°C.

Synthesis and Characterization of Novel Organomodified Nanoclays for Application in Dental Materials

2019 ◽  
Vol >15 (5) ◽  
pp. 512-524 ◽  
Author(s):  
Alexandros K. Nikolaidis ◽  
Elisabeth A. Koulaouzidou ◽  
Dimitris S. Achilias
Keyword(s):  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Fourier Transform Infrared Spectroscopy ◽  
Quaternary Ammonium ◽  
Fourier Transform Infrared ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray

Background: Nanoclays incorporated in dental resins have been previously investigated. However, limited reports are associated with nanoclays that exhibit high functionality. Objective: The aim of this study was the targeted synthesis and characterization of organomodified nanoclays with methacrylic groups suitable for incorporation in dental nanocomposite resins. Methods: Quaternary ammonium methacrylates were synthesized and characterized by means of proton nuclear magnetic resonance and Fourier-transform infrared spectroscopy. Consequently, they were inserted into the interlayer space of nanoclay through a cation exchange reaction, while silane was also used for simultaneous surface modification. The produced organomodified nanoclays were characterized by means of X-ray diffraction, Fourier-transform infrared spectroscopy and thermogravimetric analysis. Results: Fourier-transform infrared spectra confirmed the successful synthesis of the quaternary ammonium methacrylates. X-ray diffraction analysis showed that organoclays exhibited higher d001- values (up to 1.78 nm) compared to raw nanoclay (1.37 nm), indicating an accomplished intercalation in each case. X-ray diffraction spectra mainly disclosed the presence of methacrylic functional groups in all nanoclays. Thermogravimetric analysis curves verified the different thermal stability of organoclays due to the diversity of their organic modifiers. Conclusion: The experimental results showed that nanoclay was successfully modified with ammonium methacrylates and silane. Τhe combination of X-ray diffraction and thermogravimetric analysis data revealed a high degree of intercalation and methacrylated organic loading as well. These phenomena may favor a good dispersion and high polymerization degree of nanoclays with dental resin monomers, rendering them potentially useful materials for the development of advanced dental nanocomposites resins.

scholarly journals The Characteristics of Padamarang Magnesite under Calcination and Hydrothermal Treatment

2019 ◽  
Vol 29 (2) ◽  
Author(s):  
Mutia Dewi Yuniati ◽  
Feronika Cinthya Mawarni Putri Wawuru ◽  
Anggoro Tri Mursito ◽  
Iwan Setiawan ◽  
Lediyantje Lintjewas
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Fourier Transform Infrared Spectroscopy ◽  
Hydrothermal Treatment ◽  
Energy Dispersive ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Magnesite (MgCO3) is the main source for production of magnesium and its compound. In Indonesia, magnesite is quite rare and can be only found in limited amount in Padamarang Island, Southeast Sulawesi Provence. Thus the properties of magnesite and the reactivity degree of the obtained product are of technological importance. The aim of this work was to analyze the characteristics of Padamarang magnesite under calcination and hydrothermal treatment processes. The processes were carried out at various temperatures with range of 150-900°C for 30 minutes. The solids were characterized with respect to their chemical and physical properties by using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). SEM image indicates that magnesite was formed from thin and flat hexagon sheets. The FTIR and XRD analysis disclose that MgO formed at temperature above 300°C, where as the magnesite sample also lost its mass around 50%. These results demonstrate that Padamarang magnesite decomposes to magnesium oxide and carbon dioxide at high temperature.Magnesit (MgCO3) merupakan sumber utama untuk produksi magnesium dan senyawa-senyawanya. Di Indonesia, magnesit cukup jarang dan hanya dapat ditemukan dalam jumlah yang terbatas di Pulau Padamarang, Propinsi Sulawesi Tenggara. Oleh karena itu sifat magnesit dan derajat reaktivitas dari produk-produk magnesit penting untuk diketahui. Penelitian ini bertujuan untuk menganalisis karakteristik magnesit Padamarang dengan perlakuan kalsinasi dan hidrothermal.  Proses dilakukan pada temperatur yang bervariasi dari 150-900°C selama 30 menit. Sifat kimia dan fisika dari magnesit dikarakterisasi dengan menggunakan scanning electron microscopy dengan energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier-transform infrared spectroscopy (FTIR), dan X-ray diffraction (XRD). Gambar dari analisis SEM menunjukkan bahwa magnesit terbentuk dari lembaran-lembaran heksagonal yang tipis dan datar. Hasil analisis dengan FTIR dan XRD menunjukkan bahwa MgO terbentuk pada temperatur diatas 300°C, dimana sampel magnesit juga kehilangan massanya sekitar 50% pada suhu tersebut. Hal ini menunjukkan bahwa Magnesit Padamarang terdekomposisi menjadi magnesium oksida dan karbon dioksida pada temperatur tinggi.

Sign in / Sign up

Export Citation Format

Share Document