scholarly journals Mechanical and Energy Engineering The effect of titanium oxide microparticles on mechanical properties, absorption and solubility processes of a glass ionomer cement

2020 ◽  
Vol 26 (3) ◽  
pp. 160-173
Author(s):  
Howrah M.A. Abbas ◽  
Ahmed Riedh Alhamaoy ◽  
Raad Dawood Salman
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Harmful Effect ◽  
Glass Ionomer Cement ◽  
Glass Ionomer ◽  
Tio2 Particles ◽  
Biaxial Flexural Strength ◽  
Acidic Beverages ◽  
Ionomer Cement

Glass Ionomer Cement (GIC) is one of the important dental temporary filing materials. The aim of this study is to evaluate the effect of adding 3, 5 and 7 wt. % of TiO2 microparticles to conventional GIC powder (Riva Self Cure) on mechanical properties and its effect on absorption and solubility processes. TiO2 particles additives improved compressive strength and biaxial flexural strength, where the compressive strength increased with increasing in the added ratio, while the highest value of the biaxial flexural strength was at 3 wt.%. The addition of TiO2 particles improved the surface Vickers microhardness values, with highest value at 5 wt. %. On other hand TiO2 addition improves the wear resistance as additives increased. The most acidic beverages (the lowest pH value) were the most effective in increasing the absorption and solubility percentage of samples. Orange juice was more effective followed by cola and then coffee and tea were less effective. Finally, its recommended that patients should reduce drinking these acidic beverages because its harmful effect on dental fillings.

scholarly journals Mechanical Properties Enhancement of Conventional Glass Ionomer Cement by Adding Zirconium Oxide Micro and Nanoparticles

2019 ◽  
Vol 25 (2) ◽  
pp. 72-81 ◽  
Author(s):  
Ali N. Alobiedy ◽  
Ali H. Alhille ◽  
Ahmed R. Al-Hamaoy
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Wear Rate ◽  
Zirconium Oxide ◽  
Dental Materials ◽  
Glass Ionomer Cement ◽  
Nano Particles ◽  
Glass Ionomer ◽  
Biaxial Flexural Strength ◽  
Ionomer Cement

The aim of this work is to enhance the mechanical properties of the glass ionomer cement GIC (dental materials) by adding Zirconium Oxide ZrO2 in both micro and nano particles. GIC were mixed with (3, 5 and 7) wt% of both ZrO2 micro and nanoparticles separately. Compressive strength (CS), biaxial flexural strength (BFS), Vickers Microhardness (VH) and wear rate losses (WR) were investigated. The maximum compression strength was 122.31 MPa with 5 wt. % ZrO2 micro particle, while 3wt% nanoparticles give highest Microhardness and biaxial flexural strength of 88.8 VHN and 35.79 MPa respectively. The minimum wear rate losses were 3.776µg/m with 7 wt. % ZrO2 nanoparticle. GIC-containing ZrO2 micro and nanoparticles is a promising restorative material with improved mechanical properties expect wear rate losses.  

scholarly journals The Comparison of Biofilm Formation, Mechanical and Chemical Properties between Glass Ionomer Cement and Giomer

2021 ◽  
Vol 15 (1) ◽  
pp. 274-283
Author(s):  
Sylva Dinie Alinda ◽  
Anggraini Margono ◽  
Aditya Wisnu Putranto ◽  
Ike Dwi Maharti ◽  
Retno Amalina ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Surface Morphology ◽  
Biofilm Formation ◽  
Chemical Elements ◽  
Glass Ionomer Cement ◽  
Antibacterial Properties ◽  
Bacterial Biofilm ◽  
Glass Ionomer ◽  
Ionomer Cement

Aims: The aim of this study was to compare compressive strength and its correlation with the surface morphology and chemical elements of GIC and Giomer, as well as to determine the fluoride amount effect on the bacterial biofilm formation of GIC and Giomer. Background: The liability of Glass Ionomer Cement (GIC) mechanical properties is overcome with better antibacterial properties among restorative materials. Another fluoride-releasing restorative material, such as Giomer, has been discovered and is expected to overcome the issues with GIC’s mechanical properties; however, no research has been conducted related to antibacterial properties in Giomer. Objective: To compare compressive strength and its correlation with the surface morphology and chemical elements, then determine the fluoride amount effect on the bacterial biofilm formation of GIC and Giomer. Methods: Sixteen specimens of GIC and Giomer were prepared for a compressive strength measurement with the Universal Testing Machine. Sixteen specimens of GIC and Giomer were incubated for three days with the Streptococcus mutans culture at 37°C. The bacterial colonization was calculated using the Colony Forming Unit (CFU) and bacterial adhesion was calculated using a Scanning Electron Microscope (SEM). The mechanical properties’ compressive strength measurement, surface morphology, and chemical elements analyses were performed using SEM-EDX. Results: The compressive strength of Giomer was higher than GIC (P=0.001). The higher compressive strength of Giomer was reflected by a predominant regular surface, fewer voids, smaller and denser particles, and a higher content of silica and carbon. The bacterial biofilm on the surface of Giomer was higher than GIC, although there was no significant difference. GIC and Giomer have identical chemical elements: C, O, F, Na, Al, Si, P, and Ca. Conclusion: The compressive strength of Giomer is better than GIC; however, the biofilm formation of Giomer is higher than GIC, whereas GIC has a higher fluoride content but inferior in surfaces morphology characteristic

Effects of Niobium Oxide Addition on the Mechanical Properties of Glass Ionomer Cement

2015 ◽  
Vol 815 ◽  
pp. 373-378 ◽  
Author(s):  
Shi Qun Li ◽  
Bao Hui Su ◽  
Jun Guo Ran ◽  
Jun Wang ◽  
Ling Ling Yan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Vickers Hardness ◽  
Niobium Oxide ◽  
Setting Time ◽  
Sol Gel ◽  
Glass Ionomer Cement ◽  
Glass Ionomer ◽  
Ft Ir ◽  
Ionomer Cement

Aiming at inadequate mechanical properties of Glass ionomer cement (GIC) commonly used in dental clinic, commercial and melt quenched GIC powders as control groups, homemade GIC powder was prepared by sol–gel route and modified by Nb2O5. The GIC samples were characterized by X-ray Diffraction (XRD), particle size analysis, Scanning Electron Microscope (SEM) and Fourier Transform Infrared (FT-IR). The compressive strength, Vickers hardness, working and net setting time were tested. The data was analyzed by one-way ANOVA. The XRD results showed that commercial, melt quenched and sol gel GIC powders were similar amorphous. D90 of three GIC powders and Nb2O5 powder were 26 μm, 17 μm, 29 μm and 19 μm respectively. 5% Nb2O5-GIC exhibited the highest values of compressive strength and Vickers hardness, which were 112.93 Mpa, 139.48 MPa and 142.25 MPa respectively, increased 19.11%, 30.56% and 16.51% (P <0.05); the Vickers hardness were 35.15 MPa, 36.23 MPa and 37.62 MPa, increased 18.03%, 29.95% and 16.32% (P <0.05) compared to those of unmodified GICs as well. There was no significant change of the FT-IR characteristic peaks of modified GIC. The working time of three kinds of GIC were 4'58 ", 3'28" and 4'10 ", the net setting time were 5'16", 3'15 "and 4'38" (standard is 1.5-6 minutes). It was concluded that the dispersion stiffened effect of niobium oxide could improve the mechanical properties of the filling GIC without affecting the clinical operating performance.

Comparative Evaluation of Mechanical Properties of Ceramic Reinforced Glass Ionomer Cement and Type IX GIC:An Invitro Study

2019 ◽  
Vol 10 (12) ◽  
pp. 35
Author(s):  
Nagalakshmi Chowdhary ◽  
N. K. Kiran ◽  
A. Lakshmi Priya ◽  
Rajashekar Reddy ◽  
Arvind Sridhara ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Comparative Evaluation ◽  
Glass Ionomer Cement ◽  
Glass Ionomer ◽  
Ionomer Cement

scholarly journals Structural and long-term mechanical properties from a resin-modified glass ionomer cement after various delays of light-activation

2018 ◽  
Vol 37 (6) ◽  
pp. 874-879 ◽  
Author(s):  
Marianne LAGARDE ◽  
Philippe FRANCOIS ◽  
Stéphane LE GOFF ◽  
Jean-Pierre ATTAL ◽  
Elisabeth DURSUN
Keyword(s):  
Mechanical Properties ◽  
Glass Ionomer Cement ◽  
Glass Ionomer ◽  
Light Activation ◽  
Resin Modified Glass Ionomer ◽  
Ionomer Cement

scholarly journals Mechanical properties of a resin-modified glass ionomer cement for luting: effect of adding spherical silica filler

2010 ◽  
Vol 29 (3) ◽  
pp. 253-261 ◽  
Author(s):  
Lihua E ◽  
Masao IRIE ◽  
Noriyuki NAGAOKA ◽  
Takashi YAMASHIRO ◽  
Kazuomi SUZUKI
Keyword(s):  
Mechanical Properties ◽  
Glass Ionomer Cement ◽  
Glass Ionomer ◽  
Silica Filler ◽  
Spherical Silica ◽  
Resin Modified Glass Ionomer ◽  
Ionomer Cement

scholarly journals Effects of Powdery Cellulose Nanofiber Addition on the Properties of Glass Ionomer Cement

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3077 ◽  
Author(s):  
Takako Nishimura ◽  
Yukari Shinonaga ◽  
Chikoto Nagaishi ◽  
Rie Imataki ◽  
Michiko Takemura ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Cellulose Nanofibers ◽  
Glass Ionomer Cement ◽  
Chemical Properties ◽  
Fluoride Ion ◽  
Strength Testing ◽  
Glass Ionomer ◽  
Ion Release ◽  
Diametral Tensile Strength ◽  
Ionomer Cement

In this study, we aimed to evaluate the effect of the addition of powdery cellulose nanofibers (CNFs) on the mechanical properties of glass ionomer cement (GIC) without negatively affecting its chemical properties. Commercial GIC was reinforced with powdery CNFs (2–8 wt.%) and characterized in terms of flexural strength, compressive strength, diametral tensile strength, and fluoride-ion release properties. Powdery CNFs and samples subjected to flexural strength testing were observed via scanning electron microscopy. CNF incorporation was found to significantly improve the flexural, compressive, and diametral tensile strengths of GIC, and the corresponding composite was shown to contain fibrillar aggregates of nanofibers interspersed in the GIC matrix. No significant differences in fluoride-ion release properties were observed between the control GIC and the CNF-GIC composite. Thus, powdery CNFs were concluded to be a promising GIC reinforcement agent.

Sign in / Sign up

Export Citation Format

Share Document